2 layers82.5 × 101.6 mm
2 layers109.4 × 106.3 mm
Flame detect pcb
gtetil/flame-detect-pcb- Size
- 109.4 × 106.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 170
- Nets
- 120
- Pads
- 467
- Tracks, vias
- 2,054, 95
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 29 Oct 2017
- Updated
- 4 Apr 2018
Overview
Flame detect pcb is an open-source printed circuit board by gtetil, from the gtetil/flame-detect-pcb repository on GitHub. It is a 2-layer board of 109.4 × 106.3 mm with 170 parts on 120 nets, routed with 2,054 tracks and 95 vias.
It is built around the ATMEGA328P-AU, MCP2551-I/SN and LM358, with the MCP2515T-I/SO-HX, BZT52C5V1-TP and MMBT2907 among its other parts. Its parts include 67 resistors, 28 capacitors, 27 diodes, 9 transistors and 8 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
MCP2551-I/SN
SOIC-8-40℃~+85℃ 1Mbps 365uA 4.5V~5.5V 75mA CAN Transceiver SOIC-8 CAN Transceivers ROHSMicrochip TechnologyCAN Transceivers
LM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational Amplifier
MCP2515T-I/SO-HX
SOP-18SOP-18 CAN Controllers ROHSZHHXDZCAN Controllers
BZT52C5V1-TP
SOD-123-65℃~+150℃ 1 Independent 2uA@2V 4.8V~5.4V 480Ω 5.1V 500mW 60Ω SOD-123 Zener Diodes ROHSMicro Commercial ComponentsZener Diodes
MMBT2907
SOT-231 PNP 1uA 225mW 400 400mV 5V 600mA 60V PNP SOT-23 Bipolar (BJT) ROHSYONGYUTAIBipolar (BJT)MMBT2222
SOT-231 NPN 1uA 300mV 300mW 400 40V 600mA 6V NPN SOT-23 Bipolar (BJT) ROHSYONGYUTAIBipolar (BJT)
Parts
170| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | CONN_01X01 | flame-detect-pcb:KEYSTONE_SPADE_TERM_(1287) | CAN_HI_1, CAN_HI_2, CAN_LO_1, CAN_LO_2, FLAME_1, FLAME_2, FLAME_3, FLAME_4, FLAME_5, FLAME_6, FLAME_7, FLAME_8, GND_1, GND_2, V_IN_1, V_IN_2 |
| 10 | 10K | Resistors_SMD:R_0805 | R3, R4, R18, R19, R35, R36, R49, R50, R63, R64 |
| 9 | 1M | Resistors_SMD:R_0805 | R10, R12, R27, R29, R31, R43, R45, R57, R59 |
| 9 | BAV21W-7-F | Diodes_SMD:D_SOD-123 | D1, D2, D3, D8, D10, D15, D16, D21, D22 |
| 9 | LED | LEDs:LED_1206 | D6, D7, D13, D14, D19, D20, D25, D26, D27 |
| 8 | 10nF | Capacitors_SMD:C_0805 | C12, C13, C16, C17, C20, C21, C24, C25 |
| 8 | 13K | Resistors_SMD:R_0805 | R11, R13, R30, R32, R44, R46, R58, R60 |
| 8 | 1nF | Capacitors_SMD:C_0805 | C14, C15, C18, C19, C22, C23, C26, C27 |
| 8 | 240R | Resistors_SMD:R_0805 | R20, R21, R37, R38, R51, R52, R65, R66 |
| 8 | 3M | Resistors_SMD:R_0805 | R14, R17, R33, R34, R47, R48, R61, R62 |
| 8 | 470K | Resistors_SMD:R_0805 | R6, R7, R22, R23, R39, R40, R53, R54 |
| 8 | 5.1M | Resistors_SMD:R_0805 | R8, R9, R24, R25, R41, R42, R55, R56 |
| 8 | BZT52C5V1-TP | Diodes_SMD:D_SOD-123 | D4, D5, D11, D12, D17, D18, D23, D24 |
| 8 | MMBT2907 | TO_SOT_Packages_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 6 | 0.1uF | Capacitors_SMD:C_0805 | C1, C2, C5, C10, C11, C28 |
| 4 | 22pF | Capacitors_SMD:C_0805 | C6, C7, C8, C9 |
| 4 | CONN_01X01 | flame-detect-pcb:PEM_STANDOFF_THRU_(SMTSOB-116-12ET) | GND_3, GND_4, GND_5, GND_6 |
| 4 | LM358 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U1, U2, U3, U4 |
| 3 | CONN_01X01 | flame-detect-pcb:SPARE_THROUGH_HOLE | DIO7, DIO8, DIO9 |
| 2 | 47uF | Capacitors_SMD:CP_Elec_6.3x5.3 | C3, C4 |
| 2 | Crystal | Crystals:Crystal_SMD_HC49-SD | XTAL1, XTAL2 |
| 1 | 10M | Resistors_SMD:R_0805 | R16 |
| 1 | 10k | Resistors_SMD:R_0805 | R15 |
| 1 | 120R | Resistors_SMD:R_0805 | R5 |
| 1 | 1K | Resistors_SMD:R_0805 | R67 |
| 1 | 1k | Resistors_SMD:R_0805 | R28 |
| 1 | 5.1K | Resistors_SMD:R_0805 | R1 |
| 1 | 560R | Resistors_SMD:R_0805 | R2 |
| 1 | 680R | Resistors_SMD:R_0805 | R26 |
| 1 | ATMEGA328P-AU | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | U6 |
| 1 | CONN_01X02 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm_SMD_Pin1Right | CAN_TERM_1 |
| 1 | CONN_01X04 | Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mm_SMD_Pin1Right | SERIAL_1 |
| 1 | CONN_02X03 | Pin_Headers:Pin_Header_Straight_2x03_Pitch2.54mm_SMD | ICSP_1 |
| 1 | DIP_SW_3 | Buttons_Switches_SMD:SW_DIP_x3_W8.61mm_Slide_LowProfile | CAN_ADDR_1 |
| 1 | D_Schottky | flame-detect-pcb:DO-214AB | D9 |
| 1 | LM3480-5.0 | TO_SOT_Packages_SMD:SOT-23 | U5 |
| 1 | MCP2515T-I/SO | Housings_SOIC:SOIC-18W_7.5x11.6mm_Pitch1.27mm | U7 |
| 1 | MCP2551-I/SN | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U8 |
| 1 | MMBT2222 | TO_SOT_Packages_SMD:SOT-23 | Q17 |
| 1 | Polyfuse | Resistors_SMD:R_1812 | F1 |
| 1 | TRANSFORMER_(42TL013-RC) | flame-detect-pcb:TRANSFORMER_(42TL013-RC) | T1 |
Similar boards
- 2 layers91 × 77.5 mm
- 2 layers114.9 × 76 mm
Protected power entry
absmach/synth
Open-source circuit compiler for engineers and AI agents
84 parts29Apache-2.0 - 4 layers228.6 × 110.7 mm
Driver test
thewonderidiot/lachesis
Portable, safe readers for Apollo Guidance Computer core rope memory modules
225 parts4MIT - 2 layers160 × 100 mm
Mains 18V TEC
scular-HCC/DualLaserPDHDriver
Dual laster Pound-Dreaver-Hall driver setup. 1550 nm DFBs. Q=10^-5. Less than 20 GHz difference
88 parts - 4 layers118 × 117 mm
Cm4-robot
Twisted-Fields/acorn-robot-electronics
PCB hardware designs in KICAD for Acorn, the precision farming rover from Twisted Fields.
268 parts81 - 2 layers52 × 36 mm
CyphalPicoBase CAN
generationmake/CyphalPicoBase-CAN
Board for the Raspberry Pi Pico to connect via CAN using OpenCyphal and UCANPHY Micro
62 parts5CERN-OHL-W-2.0 - 4 layers45 × 63.8 mm
Questions
How big is the Flame detect pcb PCB?
It measures 109.4 × 106.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Flame detect pcb use?
170 parts, built around the ATMEGA328P-AU, MCP2551-I/SN, LM358 and MCP2515T-I/SO-HX. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flame detect pcb KiCad files?
From the gtetil/flame-detect-pcb repository on GitHub, at the commit this page was made from: the board is flame-detect-pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flame detect pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask gtetil before reusing the design.