

HC ohm tester
Battery Management System
- Size
- 27.1 × 48.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 30
- Nets
- 37
- Pads
- 118
- Tracks, vias
- 235, 128
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 11 May 2025
- Updated
- 15 Sep 2026
Overview
HC ohm tester is an open-source printed circuit board by Gregification, from the Gregification/BeeMS repository on GitHub, published under the MIT licence. It is a 2-layer board of 27.1 × 48.3 mm with 30 parts on 37 nets, routed with 235 tracks and 128 vias.
It is built around the AP63205WU, ISO7730FQDBQQ1 and NTMFS0D8N03C. Its parts include 7 capacitors, 6 ICs, 6 connectors, 4 resistors and 2 transistors. It belongs with the power boards of this library.
Main components
3AP63205WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC ConvertersISO7730FQDBQQ1
SSOP-16-40℃~+125℃ 0 100Mbps 100kV/us 3 3 Fail-safe output SSOP-16 Digital Isolators ROHSTexas InstrumentsDigital IsolatorsNTMFS0D8N03C
DFN-5(5.9x4.9)-55℃~+175℃ 1 N-channel 1.15mΩ@4.5V 110nC@10V 122pF 2.2V 30V 337A 4nF 54W 7.69nF N-Channel DFN-5(5.9x4.9) MOSFETs ROHSonsemiMOSFETs
README
README.mdBeeMS
Battery Management System (BMS)
a work in progress
BMS for University Of Texas At Arlington's FSAE Race team's E27 vehicle.
point of contact for this repo is George Boone
Development
- Code Composer Studio 12
- dependency on Driver Lib
- projects are stand alone, no dependencies on other projects in this repo.
- Kicad 9
- common symbol and footprint library shared amongst all Kicad projects. "zzLocal".
goerge (Gorge Albrecht) is not in any way involved or associated with this project. that account was accidentally listed as a contributor because of a typo in the spelling of george (George Boone).
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 22u | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C3, C4, C5, C7 |
| 4 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2, JP3, JP4 |
| 4 | ~50k | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2, R3, R6 |
| 3 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J2, J3 |
| 2 | 100n | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C6 |
| 2 | MCP3550-50-EMS | Package_SO:MSOP-8_3x3mm_P0.65mm | U1, U2 |
| 1 | 10u | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2 |
| 1 | 2N3904 | Package_TO_SOT_THT:TO-92_Inline | Q1 |
| 1 | 4.7u | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | AP63205WU | Package_TO_SOT_SMD:TSOT-23-6 | U3 |
| 1 | AZ1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | Conn_01x08_Pin | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J5 |
| 1 | DCPS+ | MountingHole:MountingHole_3mm_Pad_TopBottom | J4 |
| 1 | ISO7730FQDBQQ1 | HC_ohm_tester:DBQ16_TEX-M | U6 |
| 1 | ISO7731FQDBQQ1 | HC_ohm_tester:DBQ16_TEX-M | U4 |
| 1 | NTMFS0D8N03C | Package_SO:ONSemi_SO-8FL_488AA | Q3 |
| 1 | ~ | MountingHole:MountingHole_3mm_Pad_TopBottom | J6 |
More from Gregification/BeeMS
12- 2 layers319.7 × 58.4 mm

- 2 layers60 × 100 mm

- 2 layers50 × 110.1 mm

- 2 layers50 × 105 mm

- 2 layers78.7 × 81.8 mm

- 2 layers60 × 60 mm

- 2 layers

- 2 layers22.6 × 60.7 mm

- 2 layers34.4 × 55.3 mm

- 2 layers27.9 × 48.8 mm

- 2 layers57.5 × 38.3 mm

- 2 layers394.2 × 72.6 mm

Similar boards
- 2 layers28.3 × 14.3 mm

Tap Photosensor PCB
VoronDesign/Voron-Tap
Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:
18 parts716GPL-3.0 - 6 layers84 × 98 mm

FujiNet-5200-Rev0
FujiNetWIFI/fujinet-hardware
Schematics and design files for FujiNet hardware
145 parts142 - 2 layers65 × 70 mm

Openradfan
andrekuehne/openradfan
An ESPHome-driven controller for radiator fans to improve heat output
49 parts29MIT - 4 layers96 × 172 mm

- 4 layers355 × 160 mm

LiBCM
doppelhub/Honda_Insight_LiBCM
Replacement BCM for G1 Honda Insight Lithium Conversion
717 parts25CC-BY-SA-4.0 - 2 layers82.5 × 140 mm

QCamPCR
GaudiLabs/qPocketPCR
Quantitative PCR machine detecting fluorescence using a camera
113 parts22GPL-3.0 - 2 layers28.8 × 14.3 mm

Tap Photosensor PCB
Qballjos/Voron-2.4-Otopus-pro-SB2209-U2C-CAN
Voron 2.4 R2 with ,Stealthburner, Voron Tap, Bambu lab Hotend. Octopus pro with TMC2209 UART, EBB SB2209 v1.0 and U2C v2.1 running klipper
12 parts21 - 2 layers130 × 53 mm

TougherPowerMeter FeatherWing
ahillbom/TougherPowerMonitor-HW
Triple-channel power monitor based on INA3221 and TPS1HB08A with some filtering for tougher conditions. Compatible with Arduino Nano and Feathers.
85 parts19MIT
Questions
How big is the HC ohm tester PCB?
It measures 27.1 × 48.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the HC ohm tester use?
30 parts, built around the AP63205WU, ISO7730FQDBQQ1 and NTMFS0D8N03C. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HC ohm tester KiCad files?
From the Gregification/BeeMS repository on GitHub, at the commit this page was made from: the board is hardware/HC ohm tester/HC ohm tester.kicad_pcb and its schematic hardware/CAN DC SS switch/CAN DC SS switch.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the HC ohm tester design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).