

Mx track
Draft repo or Chunky v13 aka Zert9 MX_track
- Size
- 180.4 × 157.2 mm
- Copper layers
- 4
- Thickness
- 1.59 mm
- Parts
- 300
- Nets
- 226
- Pads
- 2,905
- Tracks, vias
- 2,882, 562
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 24 Mar 2022
- Updated
- 24 Mar 2022
Overview
Mx track is an open-source printed circuit board by freznel10, from the freznel10/Zerf9 repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 180.4 × 157.2 mm with 300 parts on 226 nets, routed with 2,882 tracks and 562 vias.
It is built around the STM32F411CEU6, W25Q128JVSIQ and SRV05-4, with the SN74LV1T34DBVR-TP, TLV75733PDBVR-MS and SK6812MINI-E among its other parts. Its parts include 66 capacitors, 59 diodes, 25 switches, 22 resistors and 16 connectors. It belongs with the STM32 boards of this library.
Main components
12STM32F411CEU6
UFQFPN-48(7x7)-40℃~+85℃ 1.7V~3.6V 100MHz 128KB 12bit 32 Bit 36 512KB ARM Cortex-M4 Built-in FLASH UFQFPN-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)SN74LV1T34DBVR-TP
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V CMOS CMOS Power-off protection Unidirectional SOT-23-5 Translators, Level Shifters ROHSTECH PUBLICTranslators, Level ShiftersTLV75733PDBVR-MS
SOT-23-5SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIUncategorisedSK6812MINI-E
SMD-40℃~+85℃ 0.6mA 1.78mm 120mcd~240mcd 120° 160mcd~320mcd 1kHz 2.8mm 2000V 3.2mm 3.7V~5.5V 460nm~470nm 515nm~525nm 620nm~625nm 800Kbit/s 815mcd~1275mcd Semi-transparent lens SMD RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)PMEG2010AEB
SOD-5231 Independent 1.5mA@20V 1A 20V 620mV@1A 6A SOD-523 Schottky Diodes ROHSNexperiaSchottky DiodesCC0402KRX5R6BB105
040210V 1uF X5R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMT0402CG200J500NT
040220pF 50V C0G ±5% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSGuangdong Fenghua Advanced Tech (FH)Multilayer Ceramic Capacitors MLCC - SMD/SMT1N4148X-TP
SOD-523-65℃~+150℃ 1 Independent 1.25V@150mA 150mA 1uA@75V 200mW 2A 4ns 75V SOD-523 Switching Diodes ROHSMicro Commercial ComponentsSwitching DiodesXSHEELNANF-25MHZ
SMD5032-2P-40℃~+85℃ 20pF 25MHz Crystal Oscillator ±30ppm ±30ppm SMD5032-2P Crystals ROHSTAITIENCrystals16-219A/T2D-AR2T1QY/3T
0402-40℃~+85℃ 130° 140mcd~180mcd 2.95V 30mW 5mA Discrete Diode White Yellow Lens 0402 LED Indication - Discrete ROHSEverlight ElectronicsLED Indication - Discrete
README
README.mdZerf9
Draft repo or Chunky v13 aka Zert9 MX_track
Parts
300| Qty | Value | Footprint | References |
|---|---|---|---|
| 59 | cap_100nF_16v_0402 | prettylib:C_0402_1005Metric-FBS | C1, C2, C3, C11, C12, C17, C20, C21, C22, C23, C24, C25, C26, C27, C28, C29 +43 |
| 37 | D | reversible-kicad-footprints:D_SOD-123 | D1, D2, D10, D11, D17, D18, D19, D20, D21, D22, D23, D24, D25, D26, D27, D28 +21 |
| 25 | Jumper_NO_Small | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1, JP2, JP10, JP11, JP12, JP13, JP14, JP15, JP16, JP17, JP18, JP19, JP20, JP21, JP22, JP23 +9 |
| 24 | jumper_smd | swoop:Jumper | W1, W2, W10, W11, W12, W13, W14, W15, W16, W17, W18, W19, W20, W21, W22, W23 +8 |
| 19 | SW_PUSH_LED | prettylib:MX_KAILH_SOCKET_1U-LED-FBS | SW1, SW3, SW12, SW16, SW17, SW19, SW21, SW22, SW24, SW26, SW27, SW29, SW31, SW32, SW34, SW36 +3 |
| 14 | 4A/0805 | reversible-kicad-footprints:L-0805_2012Metric | FB1, FB2, FB3, FB4, FB5, FB6, FB7, FB8, FB9, FB10, FB11, FB12, FB13, FB14 |
| 13 | SW_PUSH_LED | prettylib:MX_KAILH_SOCKET_1U-LED-FBS-rot | locked, SW2, SW4, SW10, SW15, SW18, SW20, SW23, SW25, SW28, SW30, SW33, SW35 |
| 12 | SK6812MINI-E | reversible-kicad-footprints:SK6812Mini-E | D3, D4, D5, D12, D47, D48, D49, D50, D51, D52, D53, D56 |
| 11 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4, R5, R7, R8, R9, R10, R11, R19, R20, R21, R22 |
| 9 | Drill Mountpoint | DjinnFootprints:MountingHole_3.2mm_M3_Pad_Via | DRILL1, DRILL3, DRILL4, DRILL5, DRILL7, DRILL8, DRILL9, DRILL11, DRILL12 |
| 4 | PAD_SQUARE_1MM | Bonsai_C4:PAD_SQUARE_1MM | J11, J12, J13, J14 |
| 4 | locked | reversible-kicad-footprints:D_SOD-123 | D13, D14, D15, D16 |
| 3 | Hole | prettylib:JLC_SMT_Assembly_Hole | H2, H3, H4 |
| 3 | PMEG2010AEB | Bonsai_C4:D_SOD-523 | D43, D44, D54 |
| 3 | SW_Push | other_parts:MouseSwitch-FBS | SW39, SW40, SW41 |
| 2 | 4.7k | reversible-kicad-footprints:R-0805_2012Metric | R3, R6 |
| 2 | Conn_01x01_Female | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J9, J10 |
| 2 | Conn_01x12_Female | prettylib:FPC-SMD_FPC05012-09200-.5mm-rev | J7, J15 |
| 2 | Drill Mountpoint | MountingHole:MountingHole_2.2mm_M2_Pad_Via | DRILL2, DRILL10 |
| 2 | LOGO | grandiceps:Freznel | G***, G*** |
| 2 | Nexperia PUMD3,115 | Package_TO_SOT_SMD:SOT-363_SC-70-6_Handsoldering | Q3, Q4 |
| 2 | SRV05-4 | Bonsai_C4:SOT-23-6 | U1, U7 |
| 2 | SW_PUSH_LED | prettylib:MX_KAILH_solder_1U-LED-FBS(3305) | locked, SW14 |
| 2 | SW_PUSH_LED | prettylib:MX_KAILH_solder_1U-LED-FBS-rot(3305) | locked, SW13 |
| 2 | cap_1uF_10v_0402 | prettylib:C_0402_1005Metric-FBS | C14, C16 |
| 2 | cap_20pF_50v_0402 | prettylib:C_0402_1005Metric-FBS | C13, C15 |
| 2 | cap_4.7uF_10v_0402 | prettylib:C_0402_1005Metric-FBS | C10, C18 |
| 2 | r_5.1k_0402_1p | Bonsai_C4:R_0402_1005Metric | R1, R2 |
| 2 | r_75_0402_1p | Bonsai_C4:R_0402_1005Metric | R14, R17 |
| 1 | 128x128_SPI_OLED | prettylib:128x128 SSD1351 | J8 |
| 1 | 1N4148 | Bonsai_C4:D_SOD-523 | D45 |
| 1 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R18 |
| 1 | Conn_01x04_Female | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Conn_01x05_Female | Buzzard:Pimoroni Haptic Buzz DRV2605L Driver | J5 |
| 1 | Conn_01x12_Female | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J2 |
| 1 | Drill Mountpoint | MountingHole:MountingHole_3.2mm_M3_Pad_Via | DRILL6 |
| 1 | EEPROM/SPI FLASH | Bonsai_C4:SOP-8_3.9x4.9mm_P1.27mm | U6 |
| 1 | HRO-TYPE-C-31-M-12 | reversible-kicad-footprints:HRO-TYPE-C-31-M-12-HandSolderingwithSBU | J6 |
| 1 | Hole | libmodulo:SK8707-smaller hole | U2 |
| 1 | JU1 | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP25 |
| 1 | JU2 | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP26 |
| 1 | OLED | acheron_Connectors:PinHeader_1x6_P2.54mm_Vertical | J16 |
| 1 | OLED | prettylib:PIM374 1.12 OLED | J1 |
| 1 | RotaryEncoder_Switch | acheron_Hardware:ALPS_EC11E | SW38 |
| 1 | SMD-CRYSTAL-8MHZ-20PF-10PPM_2P-5.0X3.2MM_ | Bonsai_C4:X2-SMD-5.0X3.2X1.3MM | Y1 |
| 1 | SMD-LED-WHITE_0402_ | Bonsai_C4:LED_0402 | D46 |
| 1 | SMD-SWITCH-TACTILE-SPST-NO_4P-3.0MMx2.6MM_ | prettylib:SMD_Tacticle_Switch_TS24CA | K1 |
| 1 | SMD0805-100 | Bonsai_C4:F0805 | F2 |
| 1 | SMF5.0A | Bonsai_C4:D_SOD-123FL | D42 |
| 1 | SN74LV1T34DBVR | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U11 |
| 1 | STM32F411CEU6 | Bonsai_C4:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm_ThermalVias | U10 |
| 1 | TLV75733PDBVR | Bonsai_C4:SOT-23-5 | U9 |
| 1 | TYPE-C-31-M12_13 | reversible-kicad-footprints:HRO-TYPE-C-31-M-12-HandSoldering-NoSBU-11 | J4 |
| 1 | W25Q128JVSIQ | Bonsai_C4:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
| 1 | cap_10uF_10v_0402 | prettylib:C_0402_1005Metric-FBS | C19 |
| 1 | locked | other_parts:EVQWGD001-reversible | SW5 |
| 1 | locked | reversible-kicad-footprints:Piezo-KLJ-1625 | locked |
| 1 | r_100k_0402_1p | Bonsai_C4:R_0402_1005Metric | R16 |
| 1 | r_10k_0402_1p | Bonsai_C4:R_0402_1005Metric | R13 |
| 1 | r_4.7k_0402_1p | Bonsai_C4:R_0402_1005Metric | R12 |
| 1 | r_470_0402_1p | Bonsai_C4:R_0402_1005Metric | R15 |
More from freznel10/Zerf9
2- 2 layers180.4 × 157.2 mm

- 2 layers180.4 × 157.2 mm

Similar boards
- 4 layers17.8 × 51.6 mm

- 2 layers80 × 100 mm

Multicartridge smd-32u4-front dipswitch
ifilot/p2000t-cartridges
Collection of homebrew P2000T cartridges
72 parts - 2 layers53 × 21 mm

B STM32F411-EVAL R1.0
Boardoza/Boardoza_STM32F411_Black_Pill_Development_Board
Compact Black Pill STM32F411-based ARM Cortex-M4 development board offering high performance, USB-C power, and rich peripheral support for advanced embedded applications.
39 parts1CC-BY-SA-4.0 - 2 layers58.9 × 25.7 mm

LoTiBloxy
GiovaSanta/PulseOxyemeter-LotiBloxy
a bluetooth pulse oxymeter Printed Circuit Board Design Project. PCB is meant to take spo2 measurements and sends results to an application via Bluetooth
51 parts - 2 layers130 × 115 mm

Fate
hasenbanck/fate
An adapter to connect a high voltage electrostatic amplifier to an ADC for audio measurement
33 parts1 - 8 layers100 × 65 mm

MatrixDrive RevB
Matrixite/MatrixDrive
MatrixDrive is a USB-loadable Mega Drive/Genesis cartridge
143 parts - 2 layers20 × 110 mm

- 2 layers19 × 108.4 mm

Questions
How big is the Mx track PCB?
It measures 180.4 × 157.2 mm and has 4 copper layers, 1.59 mm thick.
What parts does the Mx track use?
300 parts, built around the STM32F411CEU6, W25Q128JVSIQ, SRV05-4 and SN74LV1T34DBVR-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Mx track KiCad files?
From the freznel10/Zerf9 repository on GitHub, at the commit this page was made from: the board is mx_track/mx_track.kicad_pcb and its schematic mx_track/mx_track.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Mx track design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).