
HSCanT
cherry-embedded/HSCanT-hardware
HSCanT is a USB to 4-channel CAN FD tool designed based on the HPM5321 chip.

Breakout board with CAN-FD (MCP2517/8) controller and CAN-FD (MCP2562FD) transceiver
Canfd breakout is an open-source printed circuit board by fangyufei, from the fangyufei/canfd_breakout repository on GitHub. It is a 2-layer board of 25.8 × 23.7 mm with 15 parts on 22 nets, routed with 141 tracks and 21 vias.
It is built around the PESD2CAN. Its parts include 4 capacitors, 3 resistors, 3 connectors, 2 ICs and 2 diodes. It belongs with the interfaces and adapters and microcontroller boards boards of this library.
Small footprint can-fd breakout board. Mainly used 0805 smd parts. Arduino libray acan2517fd works well.
https://github.com/pierremolinaro/acan2517FD
IO Voltage Vio can be set via 0Ohm Resistor R2=>3V3 or R3=>5V. Even when Vio is set to 3V3, the board (the transceiver) needs 5V supply for proper CAN sending.
The 40MHz crystal can be replaced by a 20MHz or 4MHz crystal. However this affects CAN timing parameters in SW.
PCB:
| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3 |
| 2 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C4, C5 |
| 2 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2, J3 |
| 1 | 40MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 470 | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | R1 |
| 1 | Conn_02x02_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J1 |
| 1 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | MCP2517FD-xSL | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1 |
| 1 | MCP2562-E-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | PESD2CAN | Package_TO_SOT_SMD:SOT-23 | D1 |

cherry-embedded/HSCanT-hardware
HSCanT is a USB to 4-channel CAN FD tool designed based on the HPM5321 chip.

ucandevices/CFDC_embedded
Embedded code and PCB for CAN FD to USB converter






Blizzard26/OAM-KNX2HovalGateway
OpenKNX Application to connect KNX Bus to Hoval TopTronic Bus
It measures 25.8 × 23.7 mm and has 2 copper layers, 1.6 mm thick.
15 parts, built around the PESD2CAN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the fangyufei/canfd_breakout repository on GitHub, at the commit this page was made from: the board is canfd_breakout/canfd_breakout.kicad_pcb and its schematic canfd_breakout/canfd_breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask fangyufei before reusing the design.