

Analog analog conv
- Size
- 30.5 × 15.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 32
- Nets
- 42
- Pads
- 124
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 7 (file 20221018)
- Created
- 18 Aug 2024
- Updated
- 8 Nov 2025
Overview
Analog analog conv is an open-source printed circuit board by ethanjamesauto, from the ethanjamesauto/modular_8bit_computer repository on GitHub. It is a 2-layer board of 30.5 × 15.2 mm with 32 parts on 42 nets.
It is built around the LM358, 74LVC1G32Z and NE555D, with the TPS76318DBV among its other parts. Its parts include 14 resistors, 8 ICs, 6 capacitors, 2 diodes and 2 connectors.
Main components
4LM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational Amplifier74LVC1G32Z
SOT-553-5-40℃~+125℃ 1 1.65V~5.5V 1.7V~2V 1.7ns@5V,50pF 32mA 32mA 74LVC Series OR Gate SOT-553-5 Logic Gates ROHSDiodes IncorporatedLogic GatesNE555D
SOIC-80℃~+70℃ 10mA 4.5V~16V SOIC-8 555 Timers / Counters ROHSTexas InstrumentsTimers / CountersTPS76318DBV
SOT-23-5-40℃~+125℃ 1 1.8V 10V 140uV 150mA 60dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdModular 8-bit Computer
This is the repository for an 8-bit computer system that is built using cards with a standardized interface.
- CPU card
- Protoboard card
- This card contains an onboard clock generator, address and data registers/buffers, and a protoboard area for testing designs.
- Bus interface modeling
Here's an example of a card:

Current Bus Specification
// The main bus wires (32+8=40 wires total)
// On the bus connector, all buses have LSBs closer to the power pins and MSBs farther away
wire VCC_5V;
wire GND;
wire clk; // generated by motherboard clock generator
wire rst_n; // probably a button on the motherboard
wire VCC_3V3;
wire we_n; // active LOW
wire oe_n; // active LOW
wire int_n; // pulled up by motherboard; driven down by any peripheral (could be used for interrupts)
wire [7:0] data;
wire [15:0] addr; // 64k address space is suppored by default. More address bits may be added later
wire [7:0] aux_bus;Parts
32| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R6, R7, R8, R9, R10, R12, R13, R14, R15 |
| 6 | C | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C3, C4, C5, C6 |
| 2 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1, J2 |
| 2 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 1 | 74LVC1G32 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U7 |
| 1 | 93LCxxBxxOT | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | LM358 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | MCP33141D | Package_SO:MSOP-10_3x3mm_P0.5mm | U5 |
| 1 | NE555D | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | TPS76318 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | ~ | Package_SO:MSOP-10_3x3mm_P0.5mm | U11 |
| 1 | ~ | Package_SO:SOIC-16_4.55x10.3mm_P1.27mm | U9 |
More from ethanjamesauto/modular_8bit_computer
12- 2 layers229.9 × 93.3 mm

- 2 layers229.9 × 83.8 mm

- 2 layers229.9 × 93.3 mm

- 2 layers229.9 × 83.8 mm

- 2 layers222.3 × 127 mm

- 2 layers86.4 × 53.8 mm

- 2 layers229.9 × 86.4 mm

- 2 layers2.8 × 6.6 mm

- 2 layers111.8 × 77.2 mm

- 2 layers48.3 × 48.3 mm

- 2 layers119.4 × 45.7 mm

- 2 layers104.1 × 50.8 mm

Similar boards
- 4 layers142 × 119.7 mm

- 2 layers25 × 40 mm

- 2 layers62 × 66.4 mm

- 2 layers62 × 84 mm

- 4 layers48.5 × 25 mm

- 4 layers100 × 50 mm

- 2 layers140.7 × 47.4 mm

EG8010 A1
Millisman/EG8010
Collection of designs for the EG8010 (ASIC for single-phase SPWM control H-bridge)
201 parts17MIT - 2 layers94.4 × 90 mm

Saturation Tester
EliMattingly22/Inductor_Saturation_Tester
A circuit to check the saturation level of different inductor cores
78 parts2MIT
Questions
How big is the Analog analog conv PCB?
It measures 30.5 × 15.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Analog analog conv use?
32 parts, built around the LM358, 74LVC1G32Z, NE555D and TPS76318DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Analog analog conv KiCad files?
From the ethanjamesauto/modular_8bit_computer repository on GitHub, at the commit this page was made from: the board is analog-analog-conv/analog-analog-conv.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Analog analog conv design in my own project?
Its repository states no licence, so its author keeps all rights: ask ethanjamesauto before reusing the design.