

QMTech MiSTeX
Hardware for MiSTeX
- Size
- 142 × 119.7 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 247
- Nets
- 353
- Pads
- 1,143
- Tracks, vias
- 2,095, 464
- Pours
- 1,073
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 1 Mar 2023
- Updated
- 13 May 2024
Overview
QMTech MiSTeX is an open-source printed circuit board by MiSTeX-devel, from the MiSTeX-devel/MiSTeX-hardware repository on GitHub. It is a 4-layer board of 142 × 119.7 mm with 247 parts on 353 nets, routed with 2,095 tracks and 464 vias.
It is built around the RP2040, ZGY133/T10(PLT) and ADV7513BSWZ, with the W25Q128JVSIQ, TPS76318DBV and U.FL-R-SMT-1(80) among its other parts. Its parts include 75 resistors, 55 capacitors, 29 connectors, 15 diodes and 7 switches. It belongs with the fPGA and programmable logic and computers and single-board computers boards and the RP2040 and FPGA and CPLD boards of this library.
Main components
12RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)ZGY133/T10(PLT)
插件Fiber optic transmitter Plugin Fiber Optical Transceivers ROHSChau LightFiber Optical TransceiversADV7513BSWZ
LQFP-64(10x10)-25℃~+85℃ 1.8V、3.3V I2C LQFP-64(10x10) Video Interface ICs ROHSAnalog DevicesVideo Interface ICsW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHTPS76318DBV
SOT-23-5-40℃~+125℃ 1 1.8V 10V 140uV 150mA 60dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsU.FL-R-SMT-1(80)
SMD-40℃~+90℃ 1 1.25mm 2mm 50Ω 6GHz Board Side IPEX Male Pin SMD Coaxial Connectors (RF) ROHSHirose ElectricCoaxial Connectors (RF)TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile SwitchesXKB5858-W-F-75
SMD-15℃~+55℃ 100,000 cycles 100mA 2.5N 30V Gull Wing Non-Latching Square Button Surface Mount, Right Angle White Without SMD Pushbutton Switches ROHSXKB ConnectionPushbutton SwitchesDSHP04TSGER
SMD,P=1.27mm-30℃~+85℃ 1.27mm 24V 25mA 3,000 Cycles 4 Black SPST SMD,P=1.27mm DIP Switches ROHSkangshenDIP SwitchesHDMI-001S
SMD19P Female HDMI-A Surface Mount, Right Angle SMD HDMI Connectors ROHSXUNPUD-Sub / VGA ConnectorsKH-HDR15P-F3.08
弯插-55℃~+105℃ 15P 3 5A Blue Female High Density D-Sub Right Angle 弯插 D-Sub / VGA Connectors ROHSShenzhen Kinghelm ElecD-Sub / VGA ConnectorsPJ-325C5-BL
插件-20℃~+70℃ 3.5mm Headphone Jack 30V 500mA 插件 Audio Connectors ROHSXKB ConnectionAudio Connectors (Headphones)
README
QMTech-MiSTeX/README.mdMiSTeX Board
Connectors and main headers
- Headers for QMTech 128 pins FPGA format (2x 2x32)
- MiSTer SDRAM module header (Terasic 2x20)
- RPi header (Orange Pi 2W) (2x20)
- SNAC user port for gamepads / mt32pi (USB3)
- VGA video out (DB15)
- HDMI video out
- Analog audio out (delta sigma) (jack 3.5)
- SPDID audio out (Toslink)
- Secondary uSD Card
- PMOD J11 header (GPIO / I2S / Delta-sigma)
- USB C for RP2040 programming
- USB C power supply
Power Supply
It is recommended to use the USB power port since it uses a voltage filter. This port supply power to FPGA and Orange Pi as well.
The Jumper on the power port is for an external power switch mounted in a case for example.
J18 needs to be shorted with a jumper if no switch is placed.
You can of course also power the board from the core board barrel jack.
FPGA programming
Connect an USB-C from RP2040 port to the USB HUB you are using
Connect Dupont wires from FPGA JTAG to JTAG header on MiSTeX board
Switches / Jumpers / small headers / Leds
J9 RC2040 Boot jumper. Short to reprogram RC2040 firmware
J10 SCART VGA pin 9 jumper. Short to use a VGA to SCART cable
J18 Power switch (or either place a jumper if no switch is added)
IO6 Jumper - By default shorted 2-3 for most gamepads. Some accessories require additional 3V3 power supply, in that case put jumper in position 1-2 next to +3V3 text.
SW1 Button User (RPi/Orange Pi)
SW2 Button OSD (RPi/Orange Pi)
SW3 Button Reset (RPi/Orange Pi)
SW4 Button Menu (RPi/Orange Pi)
The side switches SW5, SW6 are currently unused and have been erroneously momentary in rev1, but should actually be latching which has been fixed in rev2
-
SW5 (FPGA) will be used to switch the Pmod signals from I2S to general purpose use
-
SW6 (RPi/Orange Pi) is intended to switch the SNAC port from SNAC to mt32pi mode
The DIP switches are currently unused too (RPi/Orange Pi).
User / HDD / Power Leds
DBG J7 Debug UART (RC2040)
SWD J12 Header (RC2040)
JTAG J6 Header (RC2040)
ADC J14 Header (3 ADC + 1 GPIO) (RC2040)
SD image (placed at Orange Pi SD slot)
$ wget -c http://www.hans-baier.de/static/mistex-orangepizero2w.img.xz
$ md5sum mistex-orangepizero2w.img.xz
30ea6324ea5340d76d8ffbd25d986887 mistex-orangepizero2w.img.xzThe boot image needs the menu core at /media/fat/menu.bit or menu.rbf for Altera boards The sdcard image above is preconfigured for the Artix 100t QmTech with pre built cores But A200T and K325T cores are included too You only need to copy the right one to menu.bit
RP2040 firmware
You need to bridge the boot jumper J9 and plug the RC2040 USB port into a PC to flash this firmware: https://github.com/MiSTeX-devel/pico-dirtyJtag/releases/tag/v0.0.1 The core FPGA board needs to be present there because it powers the 2040 except you power the 3.3v rails from another source.
Connect power supply either to FPGA barrel or USB-C power port.
Copy the uf2 file into the mass storage device that appears on PC. When the file disappears it means it is flashing the firmware. Wait a bit and disconnect USB-C and remove jumper.
Parts
247| Qty | Value | Footprint | References |
|---|---|---|---|
| 26 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C11, C12, C13, C14, C15, C16, C23, C24, C25, C26, C27, C28, C29, C30, C31 +10 |
| 20 | TestPoint_Flag | TestPoint:TestPoint_Pad_D1.5mm | TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18, TP19, TP20, TP21, TP22, TP23, TP24, TP25 +4 |
| 15 | 1k | Resistor_SMD:R_0402_1005Metric | R9, R11, R31, R36, R37, R53, R54, R55, R56, R59, R60, R61, R63, R65, R70 |
| 15 | 1k | easyeda2kicad:RES-ARRAY-SMD_0603-8P-L3.2-W1.6-BL | RN1, RN2, RN3, RN4, RN5, RN6, RN7, RN8, RN9, RN10, RN11, RN12, RN13, RN14, RN15 |
| 10 | TPD4E05U06DQAR_C2972498 | easyeda2kicad:DFN2510-10_L2.5-W1.0-P0.50-BL | D1, D2, D3, D4, D5, D9, D10, D12, D13, D14 |
| 9 | 100R | Resistor_SMD:R_0402_1005Metric | R26, R27, R40, R41, R42, R43, R44, R45, R46 |
| 9 | 4.7k | Resistor_SMD:R_0402_1005Metric | R38, R57, R58, R62, R64, R66, R67, R68, R69 |
| 8 | 10u | Capacitor_SMD:C_0603_1608Metric | C18, C19, C20, C21, C22, C36, C45, C54 |
| 8 | 560R | Resistor_SMD:R_0603_1608Metric | R32, R33, R34, R47, R48, R49, R50, R73 |
| 8 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J8, J15, J16, J17, J18, J19, J20, J21 |
| 7 | U.FL-R-SMT-1(80) | easyeda2kicad:RF-SMD_FRF05002-JSS103M | CN2, CN3, CN4, CN5, CN6, CN7, CN8 |
| 5 | 0R | Resistor_SMD:R_0402_1005Metric | R14, R17, R18, R19, R20 |
| 5 | 10uH | easyeda2kicad:L0805 | L1, L2, L3, L4, L5 |
| 5 | 1M | Resistor_SMD:R_0603_1608Metric | R6, R22, R25, R35, R39 |
| 4 | 10nF | Capacitor_SMD:C_0402_1005Metric | C37, C38, C39, C40 |
| 4 | 5k1 | Resistor_SMD:R_0603_1608Metric | R7, R8, R71, R72 |
| 4 | MountingHole | MountingHole:MountingHole_3mm | H1, H2, H3, H4 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3mm_Pad_Via | H5, H6, H7, H8 |
| 4 | TS-1187A-B-A-B | easyeda2kicad:SW-SMD_4P-L5.1-W5.1-P3.70-LS6.5-TL-2 | SW1, SW2, SW3, SW4 |
| 3 | 0R | Resistor_SMD:R_0805_2012Metric | R1, R3, R75 |
| 3 | 100nF | Capacitor_SMD:C_0805_2012Metric | C48, C49, C50 |
| 3 | 100uF | easyeda2kicad:C1206 | C41, C42, C46 |
| 3 | 16k | Resistor_SMD:R_0603_1608Metric | R28, R29, R30 |
| 3 | 1u | Capacitor_SMD:C_0603_1608Metric | C7, C10, C17 |
| 3 | 2k | Resistor_SMD:R_0402_1005Metric | R16, R23, R24 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP2, TP3 |
| 2 | 0R | Resistor_SMD:R_0603_1608Metric | R52, R74 |
| 2 | 100n | Capacitor_SMD:C_0603_1608Metric | C43, C52 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R12, R13 |
| 2 | 30pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9, J10 |
| 2 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7, J12 |
| 2 | Conn_02x32_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x32_P2.54mm_Vertical | J4, J5 |
| 2 | DNP | Resistor_SMD:R_0805_2012Metric | R2, R4 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP4, TP5 |
| 2 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_XKB_U262-16XN-4BVC11 | J3, J13 |
| 2 | XKB5858-W-F-75 | easyeda2kicad:SW-SMD_XKB5858-W-F-75 | SW5, SW6 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R21 |
| 1 | 10n | Capacitor_SMD:C_0805_2012Metric | C51 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C53 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | 51R | Resistor_SMD:R_0402_1005Metric | R5 |
| 1 | 6A | Inductor_SMD:L_1206_3216Metric | FB1 |
| 1 | 887R | easyeda2kicad:R0402 | R15 |
| 1 | ADV7513BSWZ | easyeda2kicad:LQFP-64_L10.0-W10.0-P0.50-LS12.0-BL-EP5.3 | U4 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J14 |
| 1 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J6 |
| 1 | Conn_02x06_Top_Bottom | Connector_PinSocket_2.54mm:PinSocket_2x06_P2.54mm_Horizontal | J11 |
| 1 | DNF | Capacitor_SMD:C_0402_1005Metric | R10 |
| 1 | DNP | Resistor_SMD:R_0603_1608Metric | R51 |
| 1 | DSHP04TSGER | easyeda2kicad:SW-SMD_8P-L6.7-W5.4-P1.27-LS8.4 | SW7 |
| 1 | D_LED_0603_Yellow | LED_SMD:LED_0603_1608Metric | D15 |
| 1 | HDMI-001S | easyeda2kicad:HDMI-SMD_HDMI-001S | HDMI1 |
| 1 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | KH-HDR15P-F3.08 | easyeda2kicad:DSUB-TH_KH-HDR15P-F3.08-VGA | VGA1 |
| 1 | MiSTer SDRAM Module | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J2 |
| 1 | OHWLOGO | Symbols:OSHW-Symbol_6.7x6mm_SilkScreen | N1 |
| 1 | P6SMB6.8CA-C78395 | easyeda2kicad:SMB_L4.6-W3.6-LS5.3-BI | D11 |
| 1 | PJ-325C5-BL | easyeda2kicad:TH_PJ-325C5-B | CN1 |
| 1 | RP2040 | easyeda2kicad:LQFN-56_L7.0-W7.0-P0.4-EP | U2 |
| 1 | RPi_GPIO | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J1 |
| 1 | TF-CARD H1.8 | easyeda2kicad:TF-SMD_TF-CARD-H1.8 | TF1 |
| 1 | TPS76318 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | U-A-39WD-W-1 | easyeda2kicad:USB-A-SMD_U-A-39WD-W-1 | USB1 |
| 1 | UWX1C101MCL1GB | easyeda2kicad:CAP-SMD_BD6.3-L6.6-W6.6-FD | C47 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |
| 1 | X322512MSB4SI | easyeda2kicad:OSC-SMD_4P-L3.2-W2.5-BL | X1 |
| 1 | ZGY133/T10(PLT) | easyeda2kicad:COMM-TH_ZGY133-T10-PLT | U5 |
| 1 | blue | LED_SMD:LED_0805_2012Metric | D7 |
| 1 | red | LED_SMD:LED_0805_2012Metric | D8 |
| 1 | white | LED_SMD:LED_0805_2012Metric | D6 |
More from MiSTeX-devel/MiSTeX-hardware
2- 4 layers61.3 × 66.3 mm

- 4 layers64.2 × 51.3 mm

Similar boards
- 2 layers100 × 90 mm

- 4 layers100 × 100 mm

Av board cb
bryfur/tang-av-scaler
PS2-class component video -> deinterlace, SMAA, scale -> 1080p60 HDMI on a Sipeed Tang Console 138K, with its AV board
318 parts - 2 layers191 × 125.5 mm

Xcku5p board
sjbar03/XCKU5P-Development-Notes
Notes while learning how to develop with the Xilinx Ultrascale+ XCKU5P FPGA. Also notes on PCB design.
96 parts3 - 6 layers115 × 38 mm

Quad hdmi tx
gyuhooo/esp32-hdmi-quad-splitter
ESP32 + Lontium LT86104SX による HDMI 1入力→4出力 (Full HD) スプリッタの検討・設計情報
147 partsMIT - 2 layers

- 2 layers42 × 98.1 mm

- 4 layers51.8 × 68.3 mm

- 2 layers34 × 24 mm

Reality from scratch motherboard
uwrealitylabs/Reality-from-scratch-motherboard
RP2040+ICM42688
50 parts1GPL-3.0
Questions
How big is the QMTech MiSTeX PCB?
It measures 142 × 119.7 mm and has 4 copper layers, 1.61 mm thick.
What parts does the QMTech MiSTeX use?
247 parts, built around the RP2040, ZGY133/T10(PLT), ADV7513BSWZ and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the QMTech MiSTeX KiCad files?
From the MiSTeX-devel/MiSTeX-hardware repository on GitHub, at the commit this page was made from: the board is QMTech-MiSTeX/QMTech-MiSTeX.kicad_pcb and its schematic MiSTeX-Pmod/MiSTeX-Pmod.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the QMTech MiSTeX design in my own project?
Its repository states no licence, so its author keeps all rights: ask MiSTeX-devel before reusing the design.