Skip to the content
2 layers94.4 × 90 mmSaturation Tester, the printed circuit board in 3D

A circuit to check the saturation level of different inductor cores

Size
94.4 × 90 mm
Copper layers
2
Thickness
1.6 mm
Parts
78
Nets
35
Pads
227
Tracks, vias
315, 177
Pours
6
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
25 Dec 2021
Updated
23 Aug 2022

Overview

Saturation Tester is an open-source printed circuit board by EliMattingly22, from the EliMattingly22/Inductor_Saturation_Tester repository on GitHub, published under the MIT licence. It is a 2-layer board of 94.4 × 90 mm with 78 parts on 35 nets, routed with 315 tracks and 177 vias.

It is built around the LM358, L7805 and NE555D, with the DMN67D7L, BSS84 and DMP4015SK3 among its other parts. Its parts include 24 capacitors, 18 resistors, 10 connectors, 8 transistors and 5 ICs.

Main components

7

README

README.md

Inductor_Saturation_Tester

A circuit to check the saturation level of different inductor cores

Parts

78
QtyValueFootprintReferences
12100uCapacitor_THT:CP_Radial_D8.0mm_P5.00mmC1, C2, C14, C16, C17, C18, C19, C20, C21, C22, C23, C24
121kResistor_SMD:R_1206_3216MetricR5, R7, R9, R12, R13, R15, R16, R17, R18, R19, R20, R21
6Conn_CoaxialConnector_Coaxial:BNC_TEConnectivity_1478204_VerticalJ2, J3, J4, J5, J7, J10
5100nCapacitor_SMD:C_0805_2012MetricC3, C8, C10, C12, C13
4DMN67D7LPackage_TO_SOT_SMD:SOT-23Q3, Q5, Q6, Q8
3LM358Package_SO:SO-8_3.9x4.9mm_P1.27mmU2, U3, U4
3MountingHoleMountingHole:MountingHole_4mmH2, H3, H4
247Resistor_SMD:R_1206_3216MetricR6, R22
2BSS84Package_TO_SOT_SMD:SOT-23Q4, Q7
2Barrel_Jack_SwitchConnector_BarrelJack:BarrelJack_HorizontalJ6, J8
2CCapacitor_SMD:C_0805_2012MetricC5, C11
2CPCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC4, C6
2D_SchottkyDiode_SMD:D_SMAD4, D5
110mResistor_SMD:R_2512_6332MetricR24
110nCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC15
110uInductor_SMD:L_Taiyo-Yuden_NR-60xx_HandSolderingL1
11uCapacitor_SMD:C_0805_2012MetricC7
122Resistor_SMD:R_1206_3216MetricR23
1249Resistor_SMD:R_1206_3216MetricR8
1CPCapacitor_THT:CP_Radial_D8.0mm_P5.00mmC9
1DDiode_SMD:D_SMAD1
1DMP4015SK3Package_TO_SOT_SMD:TO-252-3_TabPin4Q2
1DNPResistor_SMD:R_1206_3216MetricR11
1D_TVSDiode_SMD:D_SMAD2
1Ferrite_BeadResistor_SMD:R_0805_2012MetricFB1
1L7805Package_TO_SOT_THT:TO-220-3_VerticalU5
1LEDLED_SMD:LED_1206_3216MetricD3
1MountingHole_PadMountingHole:MountingHole_4.3mm_M4_PadH1
1NE555DPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU6
1NTMFS4C029NMartinos:DIO_NTS1045EMFST1GQ1
1R_POTPotentiometer_THT:Potentiometer_Bourns_PTV09A-1_Single_VerticalRV1
1SW_MEC_5EEli_Lib:BigButton_TL1100F160QSW1
1Screw_Terminal_01x03TerminalBlock:TerminalBlock_bornier-3_P5.08mmJ11
1USB_B_MicroConnector_USB:USB_Micro-B_Wuerth_629105150521J9

Similar boards

  • 4 layers140 × 90 mmTPA3255PBTL, the printed circuit board in 3D

    TPA3255PBTL

    EliMattingly22/TPA3255_ClassD_PBTL

    A KiCAD project for the TPA3255 amplifier in PBTL mode

    140 parts15MIT
  • 2 layers100 × 67 mmLed controller, the printed circuit board in 3D

    Led controller

    markus-k/led-controller-hardware

    KiCAD schematics and design files for my LED controller.

    91 parts5
  • 2 layers150 × 80 mmK3S Seq IF Sw, the printed circuit board in 3D

    K3S Seq IF Sw

    M0WGF/K3s-IF-switch-and-Sequencer

    Two port IF switch and three event sequencer for use with the Elecraft K3 and K3s transceivers.

    102 parts
  • 4 layers92.8 × 86.4 mmTPA3126, the printed circuit board in 3D

    TPA3126

    smileym4n-collab/Kicadprojects

    37 parts
  • 2 layers80 × 87 mmPower, the printed circuit board in 3D

    Power

    Tinashe-Timba/EEE4113F_GROUP_22

    71 parts
  • 2 layers135.4 × 28.4 mmMoisture Sensor, the printed circuit board in 3D

    Moisture Sensor

    JakobThiessen/OpenThread_Sensors

    Fehler im Schlatplan!!! R7, Q1 und Q2 nicht bestücken. Verbindung von Q1/pin1 zu Q2/Pin2 wie eingezeichnet herstellen und mit GPIO ein und ausschalten.

    29 partsMIT
  • 2 layers140.7 × 47.4 mmEG8010 A1, the printed circuit board in 3D

    EG8010 A1

    Millisman/EG8010

    Collection of designs for the EG8010 (ASIC for single-phase SPWM control H-bridge)

    201 parts17MIT
  • 2 layers89.9 × 76 mmWater level project, the printed circuit board in 3D

    Water level project

    halilyilmaz16/EE316-ELECTRONICS-DESIGN-PROJECT

    IZTECH EEE PROJETS LECTURE

    33 parts

Questions

How big is the Saturation Tester PCB?

It measures 94.4 × 90 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Saturation Tester use?

78 parts, built around the LM358, L7805, NE555D and DMN67D7L. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Saturation Tester KiCad files?

From the EliMattingly22/Inductor_Saturation_Tester repository on GitHub, at the commit this page was made from: the board is Inductor_Saturation_Tester-KiCAD/Saturation_Tester.kicad_pcb and its schematic Inductor_Saturation_Tester-KiCAD/Logic.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Saturation Tester design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).