Skip to the content
2 layers166 × 28 mmEt ruler litac, the printed circuit board in 3D

Et ruler litac

emtpb/et-ruler-litac1

PCB with a handy ruler, can be populated with a circuit that converts light to audio

Size
166 × 28 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
25
Pads
129
Tracks, vias
103, 64
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
19 Dec 2024
Updated
23 May 2025

Overview

Et ruler litac is an open-source printed circuit board by emtpb, from the emtpb/et-ruler-litac repository on GitHub. It is a 2-layer board of 166 × 28 mm with 27 parts on 25 nets, routed with 103 tracks and 64 vias.

It is built around the OP07. Its parts include 4 resistors, 4 connectors, 3 diodes, 2 capacitors and 2 fuses. It belongs with the audio and music boards of this library.

Main components

1

README

README.md

Light to Audio Converter (LitAC)

Did you ever look at an electrical candle and thought to yourself: "Mhmm, I really wonder what the flickering would sound like if I could hear light"? With this project you will no longer be in the dark!

A photoresistive diode picks up the flickering of your candle and converts it into an electrical signal. The signal then gets amplified (by an OP07) so you can hear it with your headphones or speakers. You can connect two "LitAC" to have them powered from the same battery, so you only need two batteries for your candle powered orchestra.

LitAC

Schematic

LitAC

Interactive BOM

An interactive html BOM page with pcb layout and material placement can be found here.

Parts

27
QtyValueFootprintReferences
2100Resistor_HYBRID-emt:R_0805_THT_10.16mm_HybridR1, R2
2Battery_Cellet-ruler-footprints:BatteryHolder_Keystone_1060_1x2032_adhesive_HybridBT1, BT2
2FuseResistor_HYBRID-emt:R_0805_THT_5.08mm_HybridF1, F2
2LEDLED_HYBRID-emt:LED_THT_SMD_Hybrid_D3.0mmD1, D2
2MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2
2Ruleret-ruler-footprints:Metric_Ruler_160mm_topG1, G2
10Resistor_HYBRID-emt:R_0805_THT_10.16mm_HybridR4
1100pCapacitor_HYBRID-emt:C_0805_THT_5.08mm_HybridC1
11MResistor_HYBRID-emt:R_0805_THT_10.16mm_HybridR3
11uCapacitor_HYBRID-emt:C_0805_THT_5.08mm_HybridC2
1AudioJack3_SwitchTRConnector_Audio:Jack_3.5mm_Ledino_KB3SPRS_HorizontalJ5
1Conn_01x03Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_VerticalJ1
1D_PhotoLED_HYBRID-emt:LED_THT_SMD_Hybrid_D5.0mmD3
1OP07Package_HYBRID-emt:DIP_SMDIP-8_W7.62mm_SocketU1
1Pmod-Interface-GPIO6Pmod_Interface-emt:Pmod_Interface_Male6J3
1Pmod-Interface-GPIO6Pmod_Interface-emt:Pmod_Interface_Female6J4
1QR ETrulesSymbol-emt:qr-studiere-et_15x16QR1
1R_PotentiometerPotentiometer_THT:Potentiometer_ACP_CA14V-15_VerticalRV1
1SW_DPDTSwitch-HYBRID-emt:Switch_DPDT_SMD_THT_Hybrid_P2.54SW1
1SpeakerConnector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_HorizontalLS1
1logoSymbol-emt:UPB-Logo_De_15.9X5.6mmUniLogo1

Similar boards

  • 2 layers130 × 80 mmSmu main 1, the printed circuit board in 3D

    Smu main 1

    jaromir-sukuba/J-SMU

    DIY source-measure unit

    210 parts244
  • 2 layers118 × 103.5 mmEV Charger2, the printed circuit board in 3D

    EV Charger2

    fotherja/EV_Charger

    Arduino Uno Code for EV Charger

    62 parts167MIT
  • 2 layers144.8 × 88.9 mmPotentiostat, the printed circuit board in 3D

    Potentiostat

    iorodeo/potentiostat

    Rodeostat design files, software and firmware

    142 parts57CC-BY-4.0
  • 2 layers256 × 121 mmForte PA Deck, the printed circuit board in 3D

    Forte PA Deck

    SP6GK/Forte-600-HF-RF-Amplifier

    Project of 600 W LDMOS amlifier based on 2xMRF300.

    170 parts17GPL-3.0
  • 2 layers71 × 51 mmLetitrain, the printed circuit board in 3D

    Letitrain

    bseibold/letitrain

    An ESP32 board intended for use with TL-136 level sensors

    47 parts5MIT
  • 2 layers245.6 × 85.9 mmMycelium pcb, the printed circuit board in 3D

    Mycelium pcb

    microresearch/mycelium

    134 parts5GPL-3.0
  • 2 layers114 × 95 mmVCU V3.2, the printed circuit board in 3D

    VCU V3.2

    HKUST-Red-Bird-Racing-EVRT/GEN5_ELEC

    Repository for RBR EVRT 2025 EE

    170 parts3
  • 4 layers70 × 70.5 mmPCB FINAL UPDATED, the printed circuit board in 3D

    PCB FINAL UPDATED

    bash227/ECG-Motor-Control-Power-Management-PCB

    A multi-function PCB integrating biomedical signal acquisition (ECG), DC motor control, and advanced power management for wearable applications.

    111 parts2MIT

Questions

How big is the Et ruler litac PCB?

It measures 166 × 28 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Et ruler litac use?

27 parts, built around the OP07. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Et ruler litac KiCad files?

From the emtpb/et-ruler-litac repository on GitHub, at the commit this page was made from: the board is et-ruler-LitAC.kicad_pcb and its schematic et-ruler-LitAC.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Et ruler litac design in my own project?

Its repository states no licence, so its author keeps all rights: ask emtpb before reusing the design.