

Reciever
Electrium Mobility W25 Remote Control Project
- Size
- 38 × 26.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 25
- Nets
- 42
- Pads
- 161
- Tracks, vias
- 224, 89
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 Jan 2025
- Updated
- 24 Apr 2025
Overview
Reciever is an open-source printed circuit board by Electrium-Mobility, from the Electrium-Mobility/RC-W25 repository on GitHub. It is a 2-layer board of 38 × 26.8 mm with 25 parts on 42 nets, routed with 224 tracks and 89 vias.
It is built around the ESP32-C6-MINI-1-N4, TCAN330D and LM66200DRL, with the SE5218ALG-LF, TXS0102DCUR and RCLAMP0521P-N among its other parts. Its parts include 5 capacitors, 5 ICs, 5 diodes, 4 resistors and 3 connectors. It belongs with the ESP32 and RISC-V boards of this library.
Main components
12ESP32-C6-MINI-1-N4
SMD-53P-106dBm -40℃~+85℃ 2.4GHz 21dBm 354mA 3V~3.6V 71mA ESP32-C6FH4 Integrated Bluetooth function、Integrated Zigbee function On-board PCB Antenna UART、SPI、I2C、GPIO、I2S SMD-53P WiFi Modules ROHSEspressif SystemsWiFi ModulesTCAN330D
SOIC-8-40℃~+125℃ 1Mbps 20uA 3V~3.6V 60mA CAN Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversLM66200DRL
SOT-583-40℃~+125℃ 1.32uA 1.6V~5.5V 2 74mΩ Reverse current blocking、Over temperature protection、With enable SOT-583 ORing Controllers ROHSTexas InstrumentsPower Distribution SwitchesSE5218ALG-LF
SOT-23-50℃~+125℃@(Tj) 1 175mV@(150mA) 20dB@(120Hz) 3.3V 5.5V 500mA 65uA Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSeaward ElecVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTXS0102DCUR
VSSOP-8-40℃~+85℃ 1 1.65V~3.6V 2 2.3V~5.5V 24Mbps Auto Direction Detection Bidirectional Push-Pull、Open-drain VSSOP-8 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersRCLAMP0521P-N
DFN1006-20.4pF 16V 3.5A@8/20us 500nA 5V 60W@8/20us 6V Bidirectional IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Single-channel TVS DFN1006-2 ESD and Surge Protection (TVS/ESD) ROHSBORNESD And Surge Protection (TVS/ESD)CGA0402X7R104K6R3GT
0402100nF 6.3V X7R ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSHREMultilayer Ceramic Capacitors MLCC - SMD/SMTRT0402BRD0710KL
0402-55℃~+155℃ 10kΩ 50V 62.5mW Thin Film Resistor ±0.1% ±25ppm/℃ 0402 Chip Resistor - Surface Mount ROHSYAGEOChip Resistor - Surface MountC1005X7S0J225KT000E
04022.2uF 6.3V X7S ±10% 0402 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSTDKMultilayer Ceramic Capacitors MLCC - SMD/SMTRT0402BRD075K6L
0402-55℃~+155℃ 5.6kΩ 50V 62.5mW Thin Film Resistor ±0.1% ±25ppm/℃ 0402 Chip Resistor - Surface Mount ROHSYAGEOChip Resistor - Surface MountTS-1088-AR02016
SMD,4x3mm-30℃~+80℃ 1.6N 100,000 cycles 12V 2mm 3.9mm 3mm 50mA Black Round Button SMD(SMT) Tab SPST Surface Mount,Vertical Without Bracket SMD,4x3mm Tactile Switches ROHSXUNPUTactile SwitchesTCC0805X5R226K6R3FT
080522uF 6.3V X5R ±10% 0805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSCCTCMultilayer Ceramic Capacitors MLCC - SMD/SMT
README
README.mdRC-W25
Electrium Mobility W25 Remote Control Project
Parts
25| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 15V TVS | Diode_SMD:D_0402_1005Metric | D1, D2, D3, D4, D5 |
| 2 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C5 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 2 | Button | footprints:SW-SMD_L3.9-W3.0-P4.45 | FLASH, RESET |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | ESP32-C6-MINI-1 | RF_Module:ESP32-C6-MINI-1 | U4 |
| 1 | LM66200 | Package_TO_SOT_SMD:SOT-583-8 | U2 |
| 1 | LOGO | LOGO | G*** |
| 1 | SE5218ALG-LF | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | TCAN330DR | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U5 |
| 1 | TWAI | footprints:CONN-SMD_PH2.0-4PWB | J3 |
| 1 | TXS0102DCU | Package_SO:VSSOP-8_2.3x2mm_P0.5mm | U1 |
| 1 | UART/I2C | footprints:CONN-SMD_PH2.0-4PWB | J2 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
More from Electrium-Mobility/RC-W25
1- 2 layers27.4 × 60 mm

Similar boards
- 4 layers55 × 55 mm

- 6 layers58 × 72 mm

12vhpwr standard
nathanfraske/CEC-Platform
ONE board file, kept current by the wave (owner directive 2026-07-25: "the current best should be placed into a candidate folder per board and kept current with only one board ideally so we have a reference").
110 partsApache-2.0 - 4 layers66 × 25.4 mm

- 2 layers90 × 75.9 mm

- 2 layers38 × 22 mm

Pressure & temperature sensor BMP388 breakout
SolderedElectronics/Pressure---temperature-sensor-BMP388-breakout-hardware-design
Hardware design, BOM, gerbers and 3D files for Pressure-&-temperature-sensor-BMP388-breakout designed by Soldered Electronics.
52 parts - 2 layers30.8 × 41.9 mm

- 2 layers100 × 50 mm

Chrismettal ESP Hiro ESP Hiro
punkfab/pcb-corpus
235 real KiCad boards from open-source hardware repositories, prepared as a placement and routing benchmark
102 parts1 - 4 layers44 × 48.1 mm

Questions
How big is the Reciever PCB?
It measures 38 × 26.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Reciever use?
25 parts, built around the ESP32-C6-MINI-1-N4, TCAN330D, LM66200DRL and SE5218ALG-LF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Reciever KiCad files?
From the Electrium-Mobility/RC-W25 repository on GitHub, at the commit this page was made from: the board is receiver/reciever.kicad_pcb and its schematic receiver/receiver/reciever.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Reciever design in my own project?
Its repository states no licence, so its author keeps all rights: ask Electrium-Mobility before reusing the design.