

Cloneduino zero
An Arduino Zero clone in a breadboard-compatible form factor.
- Size
- 50 × 19.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 53
- Pads
- 175
- Tracks, vias
- 516, 50
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Apr 2021
- Updated
- 5 Aug 2022
Overview
Cloneduino zero is an open-source printed circuit board by eepj, from the eepj/cloneduino-zero repository on GitHub. It is a 4-layer board of 50 × 19.7 mm with 34 parts on 53 nets, routed with 516 tracks and 50 vias.
It is built around the ATSAMD21G18A-AU and SPX3819M5-L-3-3. Its parts include 11 capacitors, 5 resistors, 5 connectors, 2 ICs and 2 diodes. It belongs with the SAM D and SAM boards of this library.
Main components
2ATSAMD21G18A-AU
TQFP-48-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)SPX3819M5-L-3-3
SOT-23-5-40℃~+85℃@(Ta) 1 20V 3.3V 420mV@(100mA) 500mA 5uA 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdCloneduino_Zero
An Arduino Zero clone in a breadboard-compatible form factor.
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C7, C9 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C10, C11 |
| 2 | 4k7 | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | Conn_01x20 | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J3, J4 |
| 2 | LOGO | cloneduino_zero:cloneduino_zero_bold | G***, G*** |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R5 |
| 1 | 2.2u | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | 32kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C8 |
| 1 | ATSAMD21G18A-A | Package_QFP:TQFP-48_7x7mm_P0.5mm | U2 |
| 1 | D13 | LED_SMD:LED_0402_1005Metric | D1 |
| 1 | L | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | LOGO | cloneduino_zero:cat | G*** |
| 1 | LOGO | cloneduino_zero:qr_soldermask | G*** |
| 1 | LOGO | cloneduino_zero:qr | G*** |
| 1 | MicroSD Slot | Connector_Card:microSD_HC_Molex_104031-0811 | J2 |
| 1 | PWR | LED_SMD:LED_0402_1005Metric | D2 |
| 1 | Reset Switch | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1 |
| 1 | SPX3819M5-L-3-3 | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | USB-C Receptacle | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
The 33 most common of 34 parts.
Similar boards
- 4 layers74.1 × 54.9 mm

- 4 layers25 × 0.3 mm

- 4 layers70.8 × 108 mm

- 2 layers36 × 20 mm

- 4 layers35.1 × 76.3 mm

Tiny4FSK
New-England-Weather-Balloon-Society/Tiny4FSK
Horus Binary v2 HAB Tracker
90 parts96CERN-OHL-W-2.0 - 4 layers36.6 × 60.3 mm

StratoSoar MK3.0
crnicholson/StratoSoar-MK3
StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone
85 parts43 - 4 layers42 × 83.9 mm

StratoSoar MK2.2
crnicholson/StratoSoar-MK2
StratoSoar is an engineering project that aims to be able to fly a glider (dropped from a high-altitude balloon), down to any selected coordinates.
116 parts24 - 2 layers69.8 × 40.4 mm

T Piece Kicad
calebmarting/os2026-badge
Schematics and firmware for the Open Sauce 2026 Badge and SAOs
82 parts23MIT
Questions
How big is the Cloneduino zero PCB?
It measures 50 × 19.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Cloneduino zero use?
34 parts, built around the ATSAMD21G18A-AU and SPX3819M5-L-3-3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Cloneduino zero KiCad files?
From the eepj/cloneduino-zero repository on GitHub, at the commit this page was made from: the board is Hardware/cloneduino_zero.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Cloneduino zero design in my own project?
Its repository states no licence, so its author keeps all rights: ask eepj before reusing the design.