Skip to the content
2 layers90 × 90.5 mmFLP PCB host, the printed circuit board in 3D

FLP PCB host

DSM-Interrupt/FLP

Overall Embedded segment of Project FLP

Size
90 × 90.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
92
Nets
108
Pads
425
Tracks, vias
1,213, 203
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
11 Mar 2025
Updated
2 May 2026

Overview

FLP PCB host is an open-source printed circuit board by DSM-Interrupt, from the DSM-Interrupt/FLP repository on GitHub. It is a 2-layer board of 90 × 90.5 mm with 92 parts on 108 nets, routed with 1,213 tracks and 203 vias.

It is built around the CP2104EK, ESP32-WROOM-32E and L86-M33, with the SX1278, TPS61200DRC and AMS1117-3.3 among its other parts. Its parts include 32 capacitors, 32 resistors, 8 ICs, 3 connectors and 2 transistors. It belongs with the ESP32 boards of this library.

Main components

12

README

README.md

구성

project FLP의 기기의 회로도, PCB, FW 코드 등이 담긴 파일입니다. 호스트 기기의 프레임 워크는 ESP-IDF를 이용하였고 Espressif ide를 이용하여서 CMAKE 형식의 프로젝트로 제작되었습니다. 터미널 기기의 프레임 워크는 STMCUBE를 이용하였습니다. host 기기의 같은경우 MCU는 ESP32-WROOM-32E를 이용하였으며 terminal기기의 경우 STM32F103C8T6을 사용하였습니다.

세부내용

Hardware

  • 433MHz 대역 통신을 위해 SX1278 모듈 기반의 안테나 매칭을 포함한 LoRa RF 공통 회로 설계
  • MCP73831(Li-Po 충전) 및 AP2112K-3.3(LDO)을 사용하여 USB-C/배터리 입력을 받는 3.3V 전원 시스템 공통 회로 구성
  • CP2104 USB-to-UART 브릿지 IC와 USB-C 커넥터를 사용한 PC 시리얼 통신 및 펌웨어 다운로드 공통 회로 구현
  • L86-M33 GPS 모듈을 탑재하여 위치 정보 수집을 위한 공통 회로 및 안테나 인터페이스 설계
  • Host(ESP32) 보드에 펌웨어의 효율적인 디버깅을 위한 JTAG 인터페이스 회로 추가 설계

Firmware

  • Host(ESP32) 펌웨어는 C 언어와 ESP-IDF(FreeRTOS)를 기반으로, Terminal(STM32F103) 펌웨어는 C 언어와 HAL 라이브러리를 기반으로 개발하여 LoRa 통신 시스템을 구축
  • Terminal은 UART2로 GPS 모듈의 NMEA 센텐스를 파싱하며, 5초 주기 또는 '호출'/'위험' 버튼 입력 시 고유 ID, GPS 좌표, Target ID, 위험 상태를 "ID,Lat,Lon,TargetID,Danger" 형식의 문자열 패킷으로 LoRa 전송
  • Host는 SPI를 통해 이 LoRa 패킷을 수신, split_lora_response 함수로 파싱하여 Target ID를 확인하고, TerminalDevice 구조체 배열로 관리되는 단말기 목록의 최신 GPS 좌표와 위험 상태를 갱신
  • Host는 Wi-Fi(AP+STA 모드)로 인터넷에 연결하며, WSS 클라이언트를 통해 원격 서버로 모든 단말기 정보와 자체 GPS 수신 정보를 통합하여 주기적으로 JSON 전송
  • Wi-Fi AP 모드에서 Captive Portal 기능을 포함한 웹 서버를 구동하여 사용자에게 Wi-Fi 연결 정보 및 AP 정보 설정 페이지를 제공하며, 이 설정값들과 등록된 단말기 ID 목록은 NVS에 영속 저장
  • 특정 GPIO 버튼(CTRL + FIND_HOST) 조합을 통해 10초간 '단말기 등록 모드'로 진입하며, 이 동안 수신된 "REG,,<TARGET_ID>" 형식의 LoRa 등록 요청 패킷을 처리하여 새로운 단말기를 시스템에 추가하고 NVS에 저장

Parts

92
QtyValueFootprintReferences
1110KResistor_SMD:R_0603_1608MetricR3, R4, R9, R16, R17, R18, R19, R20, R22, R32, R33
9100RResistor_SMD:R_0603_1608MetricR10, R11, R12, R13, R25, R26, R27, R28, R29
822uFCapacitor_SMD:C_0805_2012MetricC6, C11, C12, C24, C25, C29, C31, C33
64.7uFCapacitor_SMD:C_0603_1608MetricC4, C5, C9, C10, C19, C32
6PESD0402-140PESD0402-140:RESC1005X35NC8, C13, C14, C15, C16, C17
6SKRPABE010Diode_SMD:SW_SKRPABE010Ctrl1, Down1, Enter&space1, Find_Host1, S1, Up1
50.1uFCapacitor_SMD:C_0603_1608MetricC18, C23, C27, C28, C30
41uFCapacitor_SMD:C_0603_1608MetricC7, C34, C35, C37
322RResistor_SMD:R_0402_1005MetricR6, R7, R30
212pFCapacitor_SMD:C_0402_1005MetricC21, C22
21KResistor_SMD:R_0603_1608MetricR23, R31
22.2KResistor_SMD:R_0603_1608MetricR14, R15
25.1KResistor_SMD:R_0402_1005MetricR8, R21
10603L100SLYRResistor_SMD:R_0603_1608MetricF1
1100RResistor_SMD:R_0402_1005MetricR5
110103594-0001LFConnector_USB:USB_Micro-B_Amphenol_10103594-0001LF_HorizontalCharger1
112402012E212A12402012E212A:AMPHENOL_12402012E212AUART1
1180KResistor_SMD:R_1210_3225MetricR2
12.2uHInductor_SMD:L_1210_3225MetricL1
127pFCapacitor_SMD:C_0603_1608MetricC20
12MResistor_SMD:R_1210_3225MetricR1
132MHzCrystal:Crystal_SMD_2016-4Pin_2.0x1.6mmY1
1744028000056WE-TPC_2811:WE-TPC_2811L4
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U4
1BLM21PG221SN1DBLM21PG221SN1D:BEADC2012X105NFL1
1Battery_CellBattery:BatteryHolder_MPD_BH-18650-PC2BT1
1CP2104Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mmU5
1ESP32-WROOM-32ERF_Module:ESP32-WROOM-32EU1
1GRPB052VWVN-RCVaristor:SULLINS_GRPB052VWVN-RCJ3
1L86-M33L86-M33:XCVR_L86-M33U6
1MBRA160T3GDiode_SMD:DIOM5226X220ND1
1MCP73831-2-OTPackage_TO_SOT_SMD:SOT95P280X145-5NU3
1OLEDHTSW-104-20-TM-S:SAMTEC_HTSW-104-20-TM-SJ4
1Q_PMOS_DSGSI2333DS-T1-E3:SOT95P237X112-3NQ1
1SMA-J-P-X-ST-TH1SMA-J-P-X-ST-TH1:SAMTEC_SMA-J-P-X-ST-TH1J5
1SX1278Package_DFN_QFN:QFN-28-1EP_6x6mm_P0.65mm_EP4.8x4.8mmU7
1TPS61200DRCPackage_SON:Texas_S-PVSON-N10_ThermalViasU2
1UMH3NPackage_TO_SOT_SMD:SOT-363_SC-70-6Q2
1USBLC6-2P6Package_TO_SOT_SMD:SOT-666U8

More from DSM-Interrupt/FLP

2
  • 2 layers152.1 × 70.1 mmFLP PCB set, the printed circuit board in 3D

    FLP PCB set

    DSM-Interrupt/FLP

    Overall Embedded segment of Project FLP

    118 parts
  • 4 layers80 × 80 mmFLP PCB terminal, the printed circuit board in 3D

    FLP PCB terminal

    DSM-Interrupt/FLP

    Overall Embedded segment of Project FLP

    79 parts

Similar boards

  • 4 layers70 × 70 mmBlue interface board, the printed circuit board in 3D

    Blue interface board

    BetzDrive/interface-board

    Power and signal conditioning board for the Betz Drive system

    130 parts5
  • 2 layers152.9 × 93.6 mmController, the printed circuit board in 3D

    Controller

    dst5rfcar/Controller_Pcb

    67 parts
  • 4 layers45.3 × 31.5 mmRF Transiever, the printed circuit board in 3D

    RF Transiever

    Lonelybarbarian0/SX1278_Transiever

    48 parts1
  • 2 layers38 × 90 mmSIH Smart Irrigation System, the printed circuit board in 3D

    SIH Smart Irrigation System

    Arshsingh1602/Smart-Irrigation-System

    This is our project of SIH 2024 in which we developed a smart irrigation system that can be used to control the under and overuse of water in the feild of farmer.

    30 partsMIT
  • 2 layers36.5 × 42.5 mmPCB Design, the printed circuit board in 3D

    PCB Design

    Pritika-2024/Lora_Communication_based_real_time_tracking

    A real-time wireless tracking system using an STM32-based transmitter integrated with GPS and LoRa modules, and an ESP32-based receiver with LoRa communication.

    20 partsMIT
  • 4 layers26 × 19.1 mmCanSat, the printed circuit board in 3D

    CanSat

    TanujRai14/Sat_pcb_design

    This repository contains the PCB design files and documentation for a Can Satellite, featuring multiple environmental and orientation sensors, power management, and wireless communication capabilities.

    35 partsCERN-OHL-S-2.0
  • 4 layers40 × 40 mmCommsRev0, the printed circuit board in 3D

    CommsRev0

    Kmshanley/PicoSat-Initiative

    The pocket cube standard requires satellites to be 5x5x5cm and under 250 grams. Upon completion of this Wentworth PicoSat it will become one of the smallest satellites capable of high resolution imagery from LEO.

    39 parts3GPL-3.0
  • 2 layers137.2 × 83.8 mmPWA REV2, the printed circuit board in 3D

    PWA REV2

    PubInv/krake

    The Krake™ is a Wi-Fi–enabled server using an MQTT broker, which means it can be controlled remotely by other devices ("clients") via the internet.

    215 parts9AGPL-3.0

Questions

How big is the FLP PCB host PCB?

It measures 90 × 90.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the FLP PCB host use?

92 parts, built around the CP2104EK, ESP32-WROOM-32E, L86-M33 and SX1278. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the FLP PCB host KiCad files?

From the DSM-Interrupt/FLP repository on GitHub, at the commit this page was made from: the board is FLP_device_PCB/FLP_PCB_host/FLP_PCB_host.kicad_pcb and its schematic FLP_device_PCB/FLP_PCB_host/FLP_PCB_host.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the FLP PCB host design in my own project?

Its repository states no licence, so its author keeps all rights: ask DSM-Interrupt before reusing the design.