

Rda5807m radio
FM stereo radio receiver prototype with RDS
- Size
- 112.6 × 85.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 64
- Nets
- 58
- Pads
- 219
- Tracks, vias
- 570, 28
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Sep 2019
- Updated
- 6 May 2021
Overview
Rda5807m radio is an open-source printed circuit board by dilshan, from the dilshan/rda5807m-receiver repository on GitHub, published under the MIT licence. It is a 2-layer board of 112.6 × 85.4 mm with 64 parts on 58 nets, routed with 570 tracks and 28 vias.
It is built around the ATMEGA16A-AU, RDA5807M and LM2596T-5.0, with the M62429, L78L33ACU and 2SC945 among its other parts. Its parts include 26 capacitors, 14 resistors, 7 connectors, 6 ICs and 3 transistors. It belongs with the radio and wireless boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
6ATMEGA16A-AU
TQFP-44(10x10)-40℃~+85℃ 10bit 16KB 16MHz 1KB 2.7V~5.5V 32 512Byte 8 Bit AVR Built-in FLASH TQFP-44(10x10) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)RDA5807M
MSOP-10MSOP-10 RF Transceiver ICs ROHSRDA MicroelectronicsRF Transceiver ICsLM2596T-5.0
TO-220-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-220-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersM62429
SOP-8-20℃~+75℃ 4V~6V Volume Control SOP-8 Audio Interface ICs ROHSWuxi I-core ElecAudio Interface ICsL78L33ACU
SOT-89-30℃~+125℃@(Tj) 1 1.7V 100mA 3.3V 30V 40uV 49dB@(120Hz) 6mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators2SC945
SOT-231 NPN 100nA 150MHz 150mA 200mW 300mV 400 50V 5V NPN SOT-23 Bipolar (BJT) ROHSGuangdong HottechBipolar (BJT)
README
README.mdFM stereo radio receiver with RDS
This tuner circuit is a quick prototype which I build to test the RDA5807M FM radio tuner IC. RDA5807M is a single-chip tuner IC with RDS and MPX decoder, and it equipped with I2C interface for control.

This receiver builds around Atmel's ATmega16A 8-bit MCU. The output stage of this design consists of AN7147N, 2×5.3W audio power amplifier.
Based on the specifications of the switching-regulator and power amplifier, this circuit can drive between 9V to 20V DC input. The most recommended working voltage for this receiver is 12V.
As mentioned above this design is a quick prototype to test the features of RDA5807M tuner. Most of the parameters of this tuner are hardcoded in the firmware and not exposed in UI.
The firmware source codes of this project are released under the terms of the MIT license. All the design files and schematics are released under the terms of the Creative Commons - Attribution 4.0 International license.
Parts
64| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1MFD | Capacitor_THT:C_Rect_L10.3mm_W5.0mm_P7.50mm_MKS4 | C10, C11, C21, C22, C23, C26 |
| 4 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R6, R7, R8 |
| 3 | MountingHole:MountingHole_3.2mm_M3_ISO7380_Pad | , , | |
| 3 | 10MFD | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C3, C4, C20 |
| 3 | 470MFD | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C13, C14, C15 |
| 2 | 0.1MFD | Capacitor_THT:C_Rect_L4.6mm_W3.0mm_P2.50mm_MKS02_FKP02 | C18, C19 |
| 2 | 1000MFD | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C24, C27 |
| 2 | 12pF | Capacitor_THT:C_Disc_D4.7mm_W2.5mm_P5.00mm | C1, C2 |
| 2 | 1R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R11, R12 |
| 2 | 33MFD | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C6, C7 |
| 2 | 47K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9, R10 |
| 2 | 47MFD | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C8, C9 |
| 2 | STK7000 | Package_TO_SOT_THT:TO-92_Inline | Q2, Q3 |
| 1 | 0.22MFD | Capacitor_THT:C_Rect_L11.0mm_W6.3mm_P10.00mm_MKT | C17 |
| 1 | 0R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R13 |
| 1 | 100MFD | Capacitor_THT:CP_Radial_D7.5mm_P2.50mm | C5 |
| 1 | 10K | Potentiometer_THT:Potentiometer_Bourns_3339H_Vertical | RV1 |
| 1 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2 |
| 1 | 1N5819 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D2 |
| 1 | 2200MFD | Capacitor_THT:CP_Radial_D13.0mm_P7.50mm | C25 |
| 1 | 220MFD | Capacitor_THT:CP_Radial_D8.0mm_P3.80mm | C16 |
| 1 | 22K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R4 |
| 1 | 22K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 2SC945 | Package_TO_SOT_THT:TO-92_Inline | Q1 |
| 1 | 33uH | Inductor_THT:L_Toroid_Vertical_L17.8mm_W8.1mm_P7.62mm_Bourns_5700 | L1 |
| 1 | 4.00MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | 560R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P15.24mm_Horizontal | R14 |
| 1 | 680R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3 |
| 1 | AN7147 | rda5807m-radio:SIP-12-2P | U4 |
| 1 | ANT | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J3 |
| 1 | ATmega16A | Package_DIP:DIP-40_W15.24mm_LongPads | U1 |
| 1 | BTN-IN | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J2 |
| 1 | DC-IN | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_2-G-3.81_1x02_P3.81mm_Vertical | J7 |
| 1 | L78L33 | Package_TO_SOT_THT:TO-92_Inline | U6 |
| 1 | LCD | Connector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_Vertical | J1 |
| 1 | LED | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | D1 |
| 1 | LM2596T-5 | Package_TO_SOT_THT:TO-220-5_P3.4x3.7mm_StaggerOdd_Lead3.8mm_Vertical | U5 |
| 1 | M62429 | Package_DIP:DIP-8_W7.62mm_LongPads | U3 |
| 1 | RDA5807M | rda5807m-radio:RDA5807M-MODULE | U2 |
| 1 | ROT-ENC | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J6 |
| 1 | SPK-L | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_2-G-3.81_1x02_P3.81mm_Vertical | J4 |
| 1 | SPK-R | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_2-G-3.81_1x02_P3.81mm_Vertical | J5 |
Similar boards
- 2 layers96.9 × 110.7 mm

- 2 layers63 × 85 mm

- 2 layers66.8 × 46 mm

Atmega32
vedantjadhav304/Atmega32_DEV_BOARD
Open source AVR embedded system development board based on Atmega32
23 parts2 - 2 layers106.9 × 40.8 mm

- 2 layers33 × 48.9 mm

- 2 layers74 × 56 mm

05 Atmega16 IoT
pcb-firmware-embedded/Atmega16A_temperature_monitoring
This repository contains the complete development of a temperature monitoring and alarm system based on the ATmega16A microcontroller.
29 parts - 2 layers100 × 60 mm

- 2 layers140 × 120 mm

Questions
How big is the Rda5807m radio PCB?
It measures 112.6 × 85.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rda5807m radio use?
64 parts, built around the ATMEGA16A-AU, RDA5807M, LM2596T-5.0 and M62429. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rda5807m radio KiCad files?
From the dilshan/rda5807m-receiver repository on GitHub, at the commit this page was made from: the board is design/rda5807m-radio.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rda5807m radio design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).