

ETH OPAMP DCMI FSMC CAN ENCODER CS1000
PCB board with camera and ethernet connection + CAN-bus
- Size
- 100 × 100 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 144
- Nets
- 169
- Pads
- 626
- Tracks, vias
- 2,493, 454
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 2 Jun 2022
- Updated
- 9 Feb 2024
Overview
ETH OPAMP DCMI FSMC CAN ENCODER CS1000 is an open-source printed circuit board by DanielMartensson, from the DanielMartensson/STM32-Ethernet-Camera repository on GitHub, published under the MIT licence. It is a 4-layer board of 100 × 100 mm with 144 parts on 169 nets, routed with 2,493 tracks and 454 vias.
It is built around the DP83848IVV, TCAN332D and MCP4728-E/UN, with the LM1117-3.3 and BC847 among its other parts. Its parts include 41 capacitors, 39 resistors, 29 diodes, 14 connectors and 5 ICs. It belongs with the interfaces and adapters boards and the STM32 boards of this library.
Main components
5DP83848IVV
LQFP-48(7x7)-40℃~+105℃ 1 10BASE-T、100BASE-TX 10Mbit/s、100Mbit/s 270mW 3.3V MII、RMII、SNI PHY Transceiver LQFP-48(7x7) Ethernet Transceivers ROHSTexas InstrumentsEthernet TransceiversTCAN332D
SOIC-8-40℃~+125℃ 1Mbps 3V~3.6V 60mA CAN Transceiver SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversMCP4728-E/UN
MSOP-10-40℃~+125℃ 12 2.7V~5.5V 2LSB 4 40nA 6us I2C Integrated buffer、Power-on reset、Power-down mode、Programmable gain Voltage Buffer MSOP-10 Digital to Analog Converters (DAC) ROHSMicrochip TechnologyDigital To Analog Converters (DAC)LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedBC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
Parts
144| Qty | Value | Footprint | References |
|---|---|---|---|
| 30 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C20, C21, C22, C26, C27 +14 |
| 20 | BZX84Cxx | Diode_SMD:D_SOT-23_ANK | D2, D3, D4, D5, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D21, D22 +4 |
| 16 | 2.2K | Resistor_SMD:R_0603_1608Metric | R1, R2, R4, R5, R14, R15, R19, R20, R21, R33, R34, R36, R37, R41, R42, R43 |
| 10 | 10K | Resistor_SMD:R_0603_1608Metric | R22, R23, R26, R27, R28, R29, R30, R31, R32, R44 |
| 8 | D_Schottky | Diode_SMD:D_SOD-123 | D20, D23, D24, D25, D26, D27, D28, D29 |
| 4 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J_Pad1.25x1.05mm_HandSolder | C32, C37, C38, C41 |
| 4 | 49.9 | Resistor_SMD:R_0603_1608Metric | R10, R11, R12, R13 |
| 4 | BUK9Y07-30B115 | Package_TO_SOT_SMD:LFPAK56 | Q5, Q6, Q8, Q9 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.7mm_M2.5_DIN965_Pad | GND1, GND2, GND3, RJ45_GND1 |
| 4 | Screw_Terminal_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J4, J8, J12, J14 |
| 3 | 110 | Resistor_SMD:R_0603_1608Metric | R16, R17, R18 |
| 3 | 150 | Resistor_SMD:R_1206_3216Metric | R38, R39, R40 |
| 3 | Polyfuse | Resistor_SMD:R_0603_1608Metric | F1, F2, F3 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C4, C8 |
| 2 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C24, C25 |
| 2 | 4.7pF | Capacitor_SMD:C_0603_1608Metric | C39, C40 |
| 2 | Screw_Terminal_01x04 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-4_1x04_P5.00mm_Horizontal | J6, J13 |
| 2 | Screw_Terminal_01x06 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-6_1x06_P5.00mm_Horizontal | J9, J11 |
| 1 | 01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J10 |
| 1 | 1.5K | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R45 |
| 1 | 24MHz | Crystal:Crystal_SMD_EuroQuartz_MT-4Pin_3.2x2.5mm_HandSoldering | X1 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_MicroCrystal_CC7V-T1A-2Pin_3.2x1.5mm_HandSoldering | Y1 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C23 |
| 1 | 4.87K | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 50MHz | Crystal:Crystal_SMD_EuroQuartz_MT-4Pin_3.2x2.5mm_HandSoldering | X2 |
| 1 | BC847 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | Conn_02x03 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J5 |
| 1 | Conn_02x09 | Connector_PinHeader_2.54mm:PinHeader_2x09_P2.54mm_Vertical | J1 |
| 1 | Conn_02x20 | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J3 |
| 1 | DP83848I | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223 | U3 |
| 1 | MCP4728 | Package_SO:MSOP-10_3x3mm_P0.5mm | U6 |
| 1 | RJ45_LED | Connector_RJ:RJ45_Wuerth_7499010121A_Horizontal | J2 |
| 1 | STM32F407VGTx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_FSMSM | SW1 |
| 1 | TCAN332 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
Similar boards
- 4 layers96.9 × 73.9 mm

- 4 layers94.9 × 142 mm

Mikrofonarray Board Final
thivananhdao/PCB-Mikrofonarray
PCB Design for a university group project using KiCad
193 parts - 4 layers60 × 75 mm

PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io
143 parts1.7kApache-2.0 - 2 layers147.3 × 95.3 mm

Nixie proj conflict-20171112-163801
dm2lct/tlnixie
PCB files for the Turmlabor nixie clock 2.0
117 parts11GPL-3.0 - 4 layers60 × 106.5 mm

- 2 layers

- 2 layers176 × 100 mm

SmartDesk v1p0
daverowntree/SmartDesk
I open sourced a design I made a few years back for a non-paying client. Use it as you see fit!
190 parts - 2 layers100 × 100 mm

Questions
How big is the ETH OPAMP DCMI FSMC CAN ENCODER CS1000 PCB?
It measures 100 × 100 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ETH OPAMP DCMI FSMC CAN ENCODER CS1000 use?
144 parts, built around the DP83848IVV, TCAN332D, MCP4728-E/UN and LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ETH OPAMP DCMI FSMC CAN ENCODER CS1000 KiCad files?
From the DanielMartensson/STM32-Ethernet-Camera repository on GitHub, at the commit this page was made from: the board is Schematic/ETH OPAMP DCMI FSMC CAN ENCODER CS1000.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ETH OPAMP DCMI FSMC CAN ENCODER CS1000 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).