

Gear85 hotswap flex cut, number pad
Gear80 is a 80% keyboard based on the rp2040.
- Size
- 440.5 × 124.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 335
- Nets
- 237
- Pads
- 1,724
- Tracks, vias
- 2,811, 307
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 3 Mar 2024
- Updated
- 20 Jun 2026
Overview
Gear85 hotswap flex cut, number pad is an open-source printed circuit board by cosmosalad, from the cosmosalad/Gear80 repository on GitHub, published under the MIT licence. It is a 2-layer board of 440.5 × 124.9 mm with 335 parts on 237 nets, routed with 2,811 tracks and 307 vias.
It is built around the RP2040, W25Q128JVSIQ and SRV05-4, with the XC6206P332MR, MF-MSMF050-2 and X322512MSB4SI among its other parts. Its parts include 108 diodes, 32 capacitors, 20 resistors, 11 connectors and 9 ICs. It belongs with the keyboards and input and robots and motor control boards and the RP2040 boards of this library.
Main components
6RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMF-MSMF050-2
1812-40℃~+85℃ 100A 150mΩ 15V 1A 1Ω 3.2mm 5.4mm 500mA 1812 Resettable Fuses ROHSBournsResettable FusesX322512MSB4SI
SMD3225-4P-40℃~+85℃ 12MHz 20pF 80Ω Crystal Oscillator ±10ppm ±20ppm SMD3225-4P Crystals ROHSYXCCrystals
README
README.md▶ Check Out GearSeries
자작 과정(kr)
Gear80
Gear80 is a 80% keyboard based on the rp2040.
- gear80_wkl_Aluminum (CNC, Bead blasting-100 mesh + Anodizing-Black-Matte)
- gear80_wkl (sla print)
- Gear80-A_1.0mm (sla print)
Layout
- gear80 hotswap, solder
- gear80-a solder


There is also a keyboard plate.
Keyboard case corresponding to this layout.
PCB
It may differ from the sample photo and file.


This pcb was made by jlcpcb.(list of pcb parts main, daughterboard)
This pcb prepared the vial as firmware
typing sound
Gear80 / Aluminum / HMX Hyacinth v2u / PC Plate / ABS / Full foam
Gear80 / Aluminum / HMX Garnet / PC Plate / ABS / no foam
Gear80 Lite / Bsun RAW / PC Plate / ABS / Full foam
Gear80-A / sla / HMX Cheese / PC Plate / PBT / Full foam
Reference
Parts
335| Qty | Value | Footprint | References |
|---|---|---|---|
| 108 | D_Small | mcu:D_SOD-123_new | D1, D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112 +92 |
| 101 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_1u | MX1, MX10, MX11, MX100, MX101, MX102, MX103, MX104, MX105, MX106, MX107, MX108, MX109, MX110, MX111, MX112 +85 |
| 19 | , , , , , , , , , , , , , , , +3 | ||
| 18 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C4, C5, C6, C7, C10, C17, C18, C20, C21, C22, C23, C24, C25, C26 +2 |
| 12 | 5.1k | Resistor_SMD:R_0402_1005Metric | R4, R5, R6, R8, R9, R10, R11, R12, R13, R17, R18, R20 |
| 10 | 1u | Capacitor_SMD:C_0402_1005Metric | C3, C11, C12, C13, C14, C19, C27, C28, C29, C32 |
| 7 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_1.25u | MX78, MX79, MX80, MX82, MX83, MX84, MX85 |
| 6 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_1.5u | MX34, MX47, MX89, MX91, MX93, MX95 |
| 4 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R7, R16, R19 |
| 4 | 22p | Capacitor_SMD:C_0402_1005Metric | C15, C16, C30, C31 |
| 4 | 27 | Resistor_SMD:R_0402_1005Metric | R1, R2, R14, R15 |
| 4 | SW_Push | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | BOOT1, BOOT2, RESET1, RESET2 |
| 4 | stb | PCM_marbastlib-mx:STAB_MX_P_2u | S1, S2, S8, S9 |
| 3 | Conn_01x04 | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | J1, J4, J10 |
| 3 | MF-MSMF050-2 | Fuse:Fuse_1812_4532Metric | F1, F2, F3 |
| 3 | SRV05-4 | PCM_marbastlib-various:SOT-23-6-routable | U4, U5, U6 |
| 3 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2, J5, J9 |
| 2 | Conn_01x05 | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J8, J11 |
| 2 | Conn_01x10_Pin | Connector_FFC-FPC:Hirose_FH12-10S-0.5SH_1x10-1MP_P0.50mm_Horizontal | J6, J7 |
| 2 | LOGO | LOGO | GEAR, GEAR |
| 2 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1, U7 |
| 2 | W25Q128JVSIQ | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3, U9 |
| 2 | X322512MSB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1, Y2 |
| 2 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23-3 | U2, U8 |
| 2 | stb | PCM_marbastlib-mx:STAB_MX_P_2.25u | S3, S4 |
| 1 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_1.75u_STP_1.25 | MX51 |
| 1 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_1.75u | MX52 |
| 1 | SWD | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J3 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_P_2.75u | S5 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_P_7u | S6 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_P_6.25u | S7 |
More from cosmosalad/Gear80
6- 2 layers388.9 × 93.7 mm

- 2 layers393.7 × 101 mm

- 2 layers388.9 × 93.7 mm

- 2 layers388.9 × 93.7 mm

- 2 layers19 × 22.2 mm

- 2 layers18.2 × 17.5 mm

Similar boards
- 2 layers269.9 × 93.1 mm

- 2 layers284.2 × 93.7 mm

Gear60 solder
cosmosalad/Gear60
Gear60 is a 60% multi-layout keyboard based on the rp2040.
198 parts4MIT - 2 layers209.6 × 66.7 mm

- 2 layers21.1 × 45.7 mm

RP2040-base example
TT-392/RP2040-base-example
Revision 0.9 was produced at jlcpcb. The rev number was bumped to 1.0 after the pcb was tested. There were no changes between rev 0.9 and 1.0.
34 parts - 2 layers

- 2 layers44 × 60 mm

Stefanhamminga stepperdrivermodulecarrier stepperdrivermodulecarrier
oomlout/oomlout_oomp_project_bot_v_2
113 parts - 2 layers346.1 × 93.7 mm

Sifrl main pcb
ramonimbao/SpaceInvadersFRL
An F-rowless TKL keyboard case, plate, and PCB that uses the HiTek Series 725 switches.
177 parts15 - 2 layers194.3 × 79 mm

Questions
How big is the Gear85 hotswap flex cut, number pad PCB?
It measures 440.5 × 124.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gear85 hotswap flex cut, number pad use?
335 parts, built around the RP2040, W25Q128JVSIQ, SRV05-4 and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gear85 hotswap flex cut, number pad KiCad files?
From the cosmosalad/Gear80 repository on GitHub, at the commit this page was made from: the board is pcb/gear85_hotswap_flex_cut, number pad/gear85_hotswap_flex_cut, number pad.kicad_pcb and its schematic pcb/Gear80 hotswap/Gear80 hotswap.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gear85 hotswap flex cut, number pad design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
