2 layers346.1 × 93.7 mm
Sifrl main pcb
ramonimbao/SpaceInvadersFRL
An F-rowless TKL keyboard case, plate, and PCB that uses the HiTek Series 725 switches.
177 parts15
2 layers194.3 × 79 mm
- Size
- 194.3 × 79 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 115
- Nets
- 87
- Pads
- 623
- Tracks, vias
- 1,642, 251
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 1 Nov 2023
- Updated
- 18 Nov 2023
Overview
Qez is an open-source printed circuit board by IvoPo, from the IvoPo/qezberry repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 194.3 × 79 mm with 115 parts on 87 nets, routed with 1,642 tracks and 251 vias.
It is built around the RP2040, W25Q128JVSIQ and SRV05-4, with the XC6206P332MR and WS2812B among its other parts. Its parts include 29 diodes, 17 capacitors, 10 resistors, 7 connectors and 4 ICs. It belongs with the RP2040 boards of this library.
Main components
5
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
pcb/README.mdParts
115| Qty | Value | Footprint | References |
|---|---|---|---|
| 31 | MX-NoLED | MX_Only:MXOnly-1U-Hotswap | MX1, MX2, MX12, MX13, MX14, MX15, MX16, MX17, MX18, MX19, MX20, MX22, MX23, MX24, MX25, MX26 +15 |
| 19 | D_Small | elmo_custom_parts:D_SOT-23_ANK | D1, D2, D3, D4, D5, D6, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19 +3 |
| 10 | 100n | Capacitor_SMD:C_0402_1005Metric | C5, C6, C7, C9, C11, C12, C13, C14, C15, C16 |
| 9 | WS2812B | isps_various:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm_2 | D21, D22, D23, D24, D25, D26, D27, D28, D29 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric | C1, C4, C8, C10 |
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R8, R11 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R5, R9 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 27pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | Conn_01x02 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | J1, J4 |
| 2 | Conn_01x04 | ebasti:Molex_Pico-EZmate_78171-0004_1x04-1MP_P1.20mm_Vertical | J3, J5 |
| 2 | MX-NoLED | MX_Only:MXOnly-2.25U-Hotswap-ReversedStabilizers | MX35, MX39 |
| 2 | MX-NoLED | MX_Only:MXOnly-1.25U-Hotswap | MX10, MX11 |
| 2 | SW_Push | ebasti:SW_SPST_SKQG_WithStem | Boot1, Reset1 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C17 |
| 1 | 5.1k | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | Conn_01x07 | Connector_PinSocket_1.27mm:PinSocket_1x07_P1.27mm_Vertical | J7 |
| 1 | Conn_01x07 | Connector_PinSocket_2.00mm:PinSocket_1x07_P2.00mm_Vertical | J6 |
| 1 | Crystal_GND24_Small | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D20 |
| 1 | MX-LED | MX_Only:MXOnly-1.25U-Hotswap-LED | MX34 |
| 1 | MX-LED | MX_Only:MXOnly-6.25U-Hotswap-ReversedStabilizers-LED | MX41 |
| 1 | MX-NoLED | MX_Only:MXOnly-2.75U-Hotswap-ReversedStabilizers | MX33 |
| 1 | MX-NoLED | MX_Only:MXOnly-1.75U-Hotswap | MX21 |
| 1 | MX-NoLED | MX_Only:MXOnly-1.5U-Hotswap | MX30 |
| 1 | MX-NoLED | MX_Only:MXOnly-2U-Hotswap-ReversedStabilizers | MX40 |
| 1 | Polyfuse_Small | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U3 |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_C_Receptacle_USB2.0 | 0xCB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | USB1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2 |
| 1 | WS2812-Strip | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U1 |
The 113 most common of 115 parts.
Similar boards
- 2 layers440.5 × 124.9 mm
Gear85 hotswap flex cut, number pad
cosmosalad/Gear80
Gear80 is a 80% keyboard based on the rp2040.
335 parts7MIT - 2 layers269.9 × 93.1 mm
- 2 layers284.2 × 93.7 mm
Gear60 solder
cosmosalad/Gear60
Gear60 is a 60% multi-layout keyboard based on the rp2040.
198 parts4MIT - 2 layers337.2 × 122.5 mm
- 2 layers304.3 × 108.3 mm
- 2 layers284.2 × 55.6 mm
- 2 layers70 × 75 mm
Cloverpad mx
Cloverpad/cloverpad-hardware
Hardware designs for the Cloverpad, a 3-key keypad for osu!
47 partsCERN-OHL-S-2.0
Questions
How big is the Qez PCB?
It measures 194.3 × 79 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Qez use?
115 parts, built around the RP2040, W25Q128JVSIQ, SRV05-4 and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Qez KiCad files?
From the IvoPo/qezberry repository on GitHub, at the commit this page was made from: the board is pcb/qez.kicad_pcb and its schematic pcb/qez.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Qez design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).