

Gear60 solder
Gear60 is a 60% multi-layout keyboard based on the rp2040.
- Size
- 284.2 × 93.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 198
- Nets
- 125
- Pads
- 773
- Tracks, vias
- 1,359, 67
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 16 Feb 2024
- Updated
- 20 Jun 2026
Overview
Gear60 solder is an open-source printed circuit board by cosmosalad, from the cosmosalad/Gear60 repository on GitHub, published under the MIT licence. It is a 2-layer board of 284.2 × 93.7 mm with 198 parts on 125 nets, routed with 1,359 tracks and 67 vias.
It is built around the RP2040, W25Q128JVSIQ and SRV05-4, with the XC6206P332MR, MF-MSMF050-2 and TYPE-C-31-M-12 among its other parts. Its parts include 66 diodes, 16 capacitors, 9 resistors, 9 switches and 4 ICs. It belongs with the keyboards and input boards and the RP2040 boards of this library.
Main components
7RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHSRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)XC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMF-MSMF050-2
1812-40℃~+85℃ 100A 150mΩ 15V 1A 1Ω 3.2mm 5.4mm 500mA 1812 Resettable Fuses ROHSBournsResettable FusesTYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB ConnectorsX322512MSB4SI
SMD3225-4P-40℃~+85℃ 12MHz 20pF 80Ω Crystal Oscillator ±10ppm ±20ppm SMD3225-4P Crystals ROHSYXCCrystals
README
README.md▶ Check Out GearSeries
프로젝트 과정(kr)
Gear60
Gear60 is a 60% multi-layout keyboard based on the rp2040.
It's mostly compatible with 60% layout keyboards. Just modify usb and plate to suit your keyboard housing
split_hhkb (fdm print)
hhkb - B type (sla print)
Layout
-
solder
-
hotswap
There is also a keyboard plate.
Keyboard case corresponding to this layout.
PCB



There is a change from the initial pcb design. More pcb
This pcb was made by jlcpcb.(list of pcb parts)
This pcb prepared the vial as firmware
Reference
Parts
198| Qty | Value | Footprint | References |
|---|---|---|---|
| 71 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1u | MX1, MX2, MX10, MX11, MX12, MX13, MX14, MX15, MX16, MX18, MX19, MX20, MX21, MX22, MX23, MX24 +55 |
| 66 | D_Small | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D17, D18, D19, D20, D21, D22, D23, D24 +50 |
| 10 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.25u | MX48, MX65, MX68, MX77, MX80, MX81, MX82, MX84, MX85, MX86 |
| 9 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C5, C7, C8, C9, C13, C14, C15, C16 |
| 5 | 1u | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C6, C10 |
| 5 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R3, R4, R5 |
| 5 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.5u | MX17, MX30, MX73, MX75, MX79 |
| 3 | stb | PCM_marbastlib-mx:STAB_MX_P_2.25u | S1, S3, S5 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R6, R9 |
| 2 | 22p | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.75u | MX33, MX60 |
| 2 | SW_Push | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | BOOT1, RESET1 |
| 2 | stb | PCM_marbastlib-mx:STAB_MX_P_2.75u | S2, S6 |
| 1 | MF-MSMF050-2 | Fuse:Fuse_2010_5025Metric | F1 |
| 1 | MX_SW_solder | PCM_marbastlib-mx:SW_MX_1.75u_STP_1.25 | MX32 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U4 |
| 1 | SRV05-4 | PCM_marbastlib-various:SOT-23-6-routable | U2 |
| 1 | TYPE-C-31-M-12 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | W25Q128JVSIQ | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U3 |
| 1 | X322512MSB4SI | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23-3 | U1 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_ISO | S9 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_P_6.25u | S8 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_P_7u | S4 |
| 1 | stb | PCM_marbastlib-mx:STAB_MX_P_2u | S7 |
More from cosmosalad/Gear60
2- 2 layers284.2 × 93.7 mm

- 2 layers284.2 × 93.7 mm

Gear60 solder rp2040zero
cosmosalad/Gear60
Gear60 is a 60% multi-layout keyboard based on the rp2040.
163 parts4MIT
Similar boards
- 2 layers74.6 × 124.9 mm

- 2 layers440.5 × 124.9 mm

Gear85 hotswap flex cut, number pad
cosmosalad/Gear80
Gear80 is a 80% keyboard based on the rp2040.
335 parts7MIT - 2 layers209.6 × 66.7 mm

- 2 layers

- 2 layers21.1 × 45.7 mm

RP2040-base example
TT-392/RP2040-base-example
Revision 0.9 was produced at jlcpcb. The rev number was bumped to 1.0 after the pcb was tested. There were no changes between rev 0.9 and 1.0.
34 parts - 2 layers285.1 × 94.6 mm

YM60JIS PCB
ymkn/YM60JIS
A JIS layout 60% hot swappable custom mechanical keyboard PCB powered by RP2040.
173 parts10MIT - 2 layers353.1 × 124.9 mm

- 2 layers285.1 × 94.6 mm

YuTofu PCB
ymkn/YuTofu
YuTofu is an unofficial compatible PCB for the well-known custom keyboard Tofu60 2.0.
169 parts5MIT
Questions
How big is the Gear60 solder PCB?
It measures 284.2 × 93.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gear60 solder use?
198 parts, built around the RP2040, W25Q128JVSIQ, SRV05-4 and XC6206P332MR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gear60 solder KiCad files?
From the cosmosalad/Gear60 repository on GitHub, at the commit this page was made from: the board is pcb/solder/gear60_solder.kicad_pcb and its schematic pcb/hotswap/gear60_hs.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gear60 solder design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).