Skip to the content
2 layers40 × 50 mmWired sculpt, the printed circuit board in 3D

KiCad design files for the Wired Sculpt conversion mod

Size
40 × 50 mm
Copper layers
2
Thickness
0.8 mm
Parts
39
Nets
73
Pads
198
Tracks, vias
435, 30
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
6 Feb 2021
Updated
13 May 2023

Overview

Wired sculpt is an open-source printed circuit board by chadaustin, from the chadaustin/wired-sculpt-pcb repository on GitHub. It is a 2-layer board of 40 × 50 mm with 39 parts on 73 nets, routed with 435 tracks and 30 vias.

It is built around the AT90USB1286-AU, USBLC6-2SC6 and 06035A160JAT2A, with the 10103594-0001LF, 150080GS75000 and 2N7002BK among its other parts. Its parts include 12 capacitors, 12 resistors, 3 ICs, 3 connectors and 2 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

12

README

README.md

Design Files for Wired Sculpt Conversion Board

This repository contains the schematic and layout files for the Microsoft Sculpt Wired Conversion Mod.

Project Updates

2021-09-07

The rev4 board design is complete.

When I upgraded the 30-pin ribbon connector to one that fit better, it lowered the resistance to the LEDs. This caused me to burn the microcontroller on a test rev3 board by drawing too much current. So the question became: what values are appropriate for "maximum" brightness on both red and green. Today I found that, given a 5.15V VUSB, whatever resistance in the flex cable, and whatever voltage drop on the LEDs, 150 Ohms gives an even brightness on both red and green. Green draws about 15 mA and red about 10 mA, both within USB low-power spec and the current limits on the microcontroller.

I added an outputs directory containing the different revisions, and gerber files and drill files generated for either PCBWay or OSH Park.

The biggest challenge right now is the chip shortage. Even some of the capacitors I chose are out of stock. The hardest component to acquire is the ESD protection IC: USBLC6-2SC6. The USBLC6-4SC6 is available, but it would require some tweaking to the PCB layout.

On the software side of things, I added an internal ring buffer for debugging the debouncer. It can be dumped to the HID debug channel by holding both shifts and pressing H. I am trying to figure out why, with my custom low-latency debouncer, sometimes "the" comes out as "theb". For anyone that isn't trying to optimize latency as much as me, you can just run with the default QMK debouncer, which I've never seen produce phantom keys.

2021-05-02

One thing that annoyed me about the previous board design was that neither LED was hooked up to a PWM-capable pin and that the green one couldn't be driven, since it wants -5V. I want both lights to work and both to be dimmable.

Rev3 includes a charge pump to produce -5V and two MOSFETs that allow switching the green cathode with PWM.

I also figured out how the Fn switch works: it's a resistor divider that toggles 47K pull-down on a pin with a permanent 1M pull-up. Rev3 includes said 1M pull-up, so the firmware can read the Fn switch's state.

Sadly, it looks like there were many arrangements of media keys on the Sculpt over the years, and most of the media keys have nonsensical icons with behavior that differs on each platform. I'll try to make at least volume and play/pause work.

The parts for board rev 3 arrived last week. Some adjustments were required due to the chip shortage, but it's not too bad. The microcontroller is still available at least.

I attempted assembly of one, and it worked fine, but I screwed up the red and green pins, so I cut some traces and bodged in some kynar wire.

Both lights work!

I have not tested PWM. I did observe that twice as much current is being drawn for each light as I expected. I fear 40 mA could burn out the lights, so I plan to measure an appropriate series resistor this week. It's possible I never had this problem before because I was using a worse-fitting ribbon connector previously. In the past, I always measured 100 Ohms on every pin, but never tested the new ribbon connector.

Also, it kind of sucks that the LED brightness is a function of USB voltage (anywhere between 4.6 V and 5.25 V), but I don't want to include a regulator...

Assembly took about five hours for one board. A lot of that was getting my desk set up. I imagine I could do three boards in ... eight? I think if I used a stencil, hot air assembly could go pretty quickly. Especially if I had a preheater like the MHP30.

A couple people have suggested I set up an Etsy, but if I properly priced in hours of my labor, it would get prohibitive. And I don't want to deal with returns and warranties.

Remaining items before I can say the board is done:

  • Order a fourth PCB design with fixed green and red pins
  • Include an 0603 resistor on each
  • Fix the debouncer
  • Add a media key QMK layer, enabled with the Fn switch.

2021-04-27

In February, I tried pushing latency further than QMK offers out of the box. I switched from the default debouncer to sym_eager_pk, but since then I've observed some false keydowns and occasionally a phantom keypress. It's common for "the" to produce "theb". (Note that I use the Dvorak key layout.) I haven't looked at the matrix, but it's clear some debouncing is needed on keydown.

I'm planning on writing a custom debouncer that requires at least two frames for a keydown to register and at least 10 ms for a keyup. Having never done AVR optimization, I am trying to get a simavr benchmark harness up to make sure I don't regress the scan rate.

Parts

39
QtyValueFootprintReferences
4CL10A105KA8NNNCCapacitor_SMD:C_0603_1608MetricC4, C5, C6, C9
4ERJ-PA3F22R0VResistor_SMD:R_0603_1608MetricR1, R2, R7, R12
3CL10B104KB8NNNCCapacitor_SMD:C_0603_1608MetricC10, C11, C12
3ERJ-3GEYJ331VResistor_SMD:R_0603_1608MetricR6, R9, R10
206035A160JAT2ACapacitor_SMD:C_0603_1608MetricC7, C8
2ERJ-PA3J472VResistor_SMD:R_0603_1608MetricR3, R8
110103594-0001LFConnector_USB:USB_Micro-B_Amphenol_10103594-0001LF_HorizontalJ1
1150080GS75000LED_SMD:LED_0603_1608Metric_CastellatedD1
12N7002BKPackage_TO_SOT_SMD:SOT-23Q2
1AT90USB1286-AUPackage_QFP:TQFP-64_14x14mm_P0.8mmU3
1AVR-ISP-6 - NOT FITTEDConnector_IDC:IDC-Header_2x03_P2.54mm_VerticalJ3
1AlignmentHoleMountingHole:MountingHole_2.7mmH3
1BSS84AK,215Package_TO_SOT_SMD:SOT-23Q1
1CL21A475KOFNNNECapacitor_SMD:C_0805_2012MetricC1
1CL21B103KBANNNCCapacitor_SMD:C_0805_2012MetricC3
1CL21B104KACNNNCCapacitor_SMD:C_0805_2012MetricC2
1ERJ-3EKF8873VResistor_SMD:R_0603_1608MetricR4
1ERJ-PA3J473VResistor_SMD:R_0603_1608MetricR5
1ERJ-PA3J560VResistor_SMD:R_0603_1608MetricR11
1FFC3B07-30-TConnector_FFC-FPC:TE_3-84952-0_1x30-1MP_P1.0mm_HorizontalJ2
1FSMSMButton_Switch_SMD:SW_SPST_FSMSMSW1
1LM2776DBVTPackage_TO_SOT_SMD:SOT-23-6U2
1MountingHoleNorthMountingHole:MountingHole_2.2mm_M2H1
1MountingHoleSouthMountingHole:MountingHole_2.2mm_M2H2
1S2B-PH-K-S(LF)(SN)Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalSW2
1TSX-3225 16.0000MF18X-AC0Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U1

Similar boards

  • 2 layers40 × 54 mmWired sculpt, the printed circuit board in 3D

    Wired sculpt

    frgrw/reiyyeesr

    This repository contains the schematic and layout files for the Microsoft Sculpt Wired Conversion Mod.

    38 parts2
  • 2 layers140 × 64.8 mmConsole hardware, the printed circuit board in 3D

    Console hardware

    ECE411-Practicum-Group11/ECE411-PracticumProject-G11

    Fall 2022 ECE 411 Practicum Project for Group 11

    68 partsCC0-1.0
  • 4 layers39.6 × 49.6 mmMS88SF3-ms keyboard, the printed circuit board in 3D

    MS88SF3-ms keyboard

    vsnrain/ms-keyboard

    Custom Microsoft Sculpt compatible board replacement using MS88SF3 NRF52840 microcontroller.

    69 parts2
  • 2 layers39.6 × 49.6 mmRp2040 stamp sculpt separated, the printed circuit board in 3D

    Rp2040 stamp sculpt separated

    techberet/msft_sculpt_rp2040_stamp_hw

    Lots of details available in my (rather long) blog post.

    8 parts9MIT
  • 4 layers110 × 64 mmSYCL Badge 2024, the printed circuit board in 3D

    SYCL Badge 2024

    ZigEmbeddedGroup/sycl-badge

    The badge for the SYCL conference! https://zigembeddedgroup.github.io/sycl-badge/

    145 parts39
  • 4 layers55 × 25 mmADF4158 PCB, the printed circuit board in 3D

    ADF4158 PCB

    daniestevez/ADF4158_PCB

    ADF4158 + HMC391 PCB for 10 GHz FMCW radar LO

    83 parts30CERN-OHL-P-2.0
  • 2 layers106.2 × 40 mmProjectTamiya TX, the printed circuit board in 3D

    ProjectTamiya TX

    lunakiller/project_tamiya

    Custom open-source RC car system based on STM32 MCUs

    45 parts8GPL-3.0

Questions

How big is the Wired sculpt PCB?

It measures 40 × 50 mm and has 2 copper layers, 0.8 mm thick.

What parts does the Wired sculpt use?

39 parts, built around the AT90USB1286-AU, USBLC6-2SC6, 06035A160JAT2A and 10103594-0001LF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Wired sculpt KiCad files?

From the chadaustin/wired-sculpt-pcb repository on GitHub, at the commit this page was made from: the board is wired-sculpt.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Wired sculpt design in my own project?

Its repository states no licence, so its author keeps all rights: ask chadaustin before reusing the design.