

ProjectTamiya TX
Custom open-source RC car system based on STM32 MCUs
- Size
- 106.2 × 40 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 45
- Nets
- 53
- Pads
- 170
- Tracks, vias
- 226, 35
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 18 Mar 2022
- Updated
- 27 Jul 2022
Overview
ProjectTamiya TX is an open-source printed circuit board by lunakiller, from the lunakiller/project_tamiya repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 106.2 × 40 mm with 45 parts on 53 nets, routed with 226 tracks and 35 vias.
It is built around the STM32F303CCT6, AP2111H-3.3TRG1 and 2N7002BK. Its parts include 14 capacitors, 11 connectors, 8 resistors, 3 transistors and 2 ICs. It belongs with the STM32 boards of this library.
Main components
3STM32F303CCT6
LQFP-48(7x7)-40℃~+85℃ 12bit 12bit 256KB 2V~3.6V 32 Bit 37 40KB 72MHz ARM Cortex-M4 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)AP2111H-3.3TRG1
SOT-223-40℃~+85℃@(Ta) 1 250mV@(600mA) 3.3V 50uVrms 55uA 600mA 65dB@(1kHz) 6V Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators2N7002BK
SOT-23-55℃~+150℃ 1 N-channel 1.6Ω@10V 2.1V 350mA 370mW 4pF 50pF 600pC@4.5V 60V N-Channel SOT-23 MOSFETs ROHSNexperiaMOSFETs
README
README.mdProject TAMIYA
GitHub repository for custom open-source RC car system based on STM32 microcontrollers. The project is built on top of an old Tamiya QD chassis, which was modified. The repository includes both car and transmitter software along with hardware schematics and the Bachelor's thesis with extensive description of the project.
Features
- long range (350 m+)
- high speed (35 km/h)
- smooth control (~220 Hz control loop)
- 2.4 GHz two-way communication
- available driving data:
- battery voltage and current
- BLDC shell temperature
- linear acceleration and angular velocity
- supports logging to microSD card
Car
- STM32F303CCT6 MCU
- nRF24L01+ PA + LNA module
- RC servo Emax ES3001
- GoolRC 2435 BLDC 4800Kv with 25A ESC
- OLED display and RGB LED
- ACS712 hall current sensor
- DS18B20 temperature sensor
- MPU6050 IMU
Transmitter
- STM32F303CCT6 MCU
- nRF24L01+ PA + LNA module
- OLED display and RGB LED
- Custom PCB
Parts
45| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C5, C6, C7, C11, C12, C13 |
| 3 | 2N7002BK | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 2 | 1K2 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R7 |
| 2 | 27p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C10 |
| 2 | 4u7 | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4, C8 |
| 1 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C14 |
| 1 | 180R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R8 |
| 1 | 330R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R2 |
| 1 | 3K3 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R4 |
| 1 | 4u7 | Capacitor_Tantalum_SMD:CP_EIA-1608-10_AVX-L_Pad1.25x1.05mm_HandSolder | C1 |
| 1 | 5K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R3 |
| 1 | AP2111H-3.3TRG1 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | Boot | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | Debug | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J9 |
| 1 | ENC1 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J6 |
| 1 | ENC2 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J8 |
| 1 | LED_RAGB | LED_THT:LED_D5.0mm-4_RGB | D1 |
| 1 | NRF | Connector_Wire:SolderWire-0.15sqmm_1x06_P4mm_D0.5mm_OD1.5mm_Relief | J10 |
| 1 | NRF_power | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm_Relief | J11 |
| 1 | OLED | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical_SMD_Pin1Left | J7 |
| 1 | ORANGE | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | Power | Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_Horizontal | J2 |
| 1 | Reset | Button_Switch_SMD:SW_SPST_FSMSM | SW1 |
| 1 | STM32F303CCT6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | Serial | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | Steering | Connector_Wire:SolderWire-0.25sqmm_1x03_P4.2mm_D0.65mm_OD1.7mm | J4 |
| 1 | Switch | Button_Switch_THT:SW_DIP_SPSTx02_Slide_9.78x7.26mm_W7.62mm_P2.54mm | SW2 |
| 1 | Throttle | Connector_Wire:SolderWire-0.25sqmm_1x03_P4.2mm_D0.65mm_OD1.7mm | J5 |
| 1 | XT324 [20pF, 12MHz] | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
The 43 most common of 45 parts.
Similar boards
- 4 layers190 × 135 mm

- 4 layers70.9 × 70.1 mm

Wear Camera
kitnol/Camera_project
(See the README.md file in the upper level 'examples' directory for more information about examples.)
75 parts - 2 layers31.4 × 36.4 mm

Boostlet
RobotZwrrl/boostlet
Embeddable circuit board to boost battery to 5V for small robots.
44 parts - 2 layers40 × 50 mm

Wired sculpt
chadaustin/wired-sculpt-pcb
KiCad design files for the Wired Sculpt conversion mod
39 parts35 - 4 layers55 × 25 mm

ADF4158 PCB
daniestevez/ADF4158_PCB
ADF4158 + HMC391 PCB for 10 GHz FMCW radar LO
83 parts30CERN-OHL-P-2.0 - 4 layers202.5 × 307.5 mm

Element foxtrot
visionspacetec/VST104-Foxtrot
VST104 Flat-Sat board - referred as element_foxtrot
147 parts5 - 4 layers190 × 145 mm

Motor izleme karti
melikeatilgan/asenkron-motor-bakim
15 kW asenkron motor için arıza ağacı analizi, aylık bakım formu ve KiCad'de tasarlanmış üç izleme kartı
191 parts1 - 4 layers300 × 200 mm

Prototype
mohan4220/ecu25kva
Replacement engine control unit for a 25 kVA Kirloskar diesel genset — engine 3GK550ETA 4SR1, application code GK3.8703, 26.5 kW at 1500 rpm, 12 V system. Panel controller is a Deep Sea Electronics DSE4522 MKII AMF.
434 parts
Questions
How big is the ProjectTamiya TX PCB?
It measures 106.2 × 40 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ProjectTamiya TX use?
45 parts, built around the STM32F303CCT6, AP2111H-3.3TRG1 and 2N7002BK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ProjectTamiya TX KiCad files?
From the lunakiller/project_tamiya repository on GitHub, at the commit this page was made from: the board is Hardware/Transmitter/ProjectTamiya_TX.kicad_pcb and its schematic Hardware/Car/ProjectTamiya_Car.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ProjectTamiya TX design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).