Skip to the content
2 layers40 × 54 mmWired sculpt, the printed circuit board in 3D

Wired sculpt

frgrw/reiyyeesr2

This repository contains the schematic and layout files for the Microsoft Sculpt Wired Conversion Mod.

Size
40 × 54 mm
Copper layers
2
Thickness
1.6 mm
Parts
38
Nets
83
Pads
211
Tracks, vias
353, 17
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
22 Jun 2023
Updated
22 Jun 2023

Overview

Wired sculpt is an open-source printed circuit board by frgrw, from the frgrw/reiyyeesr repository on GitHub. It is a 2-layer board of 40 × 54 mm with 38 parts on 83 nets, routed with 353 tracks and 17 vias.

It is built around the AT90USB1286-AUR, USBLC6-2SC6 and 2N7002BK,215-VB, with the BSS84AK,215(ES), CL21A475KOFNNNE and CL21B103KBANNNC among its other parts. Its parts include 13 resistors, 12 capacitors, 3 ICs, 3 connectors and 2 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

9

README

README.md

Design Files for Wired Sculpt Conversion Board

This repository contains the schematic and layout files for the Microsoft Sculpt Wired Conversion Mod.

To get the board manufactured:

  1. Install Kicad & the PCBWay plugin. Use the plugin to start an order, select HASL lead-free if you want lead-free. The other defaults should be fine. Check the box for Assembly service
  2. Upload the BOM (bill of materials) and component placement file. These are generated from Kicad: use Tools > "Generate BOM" from the Schematic Editor, and File > "Fabrication Outputs" > "Component placement (.pos)" from the PCB Editor.

Project Updates

2023-02-20

rev6 board with USB-C

Also has some adjustments to board layout, and removes RST switch header to reduce BOM

2023-01-06

rev5 board with minor updates.

Rearrange the board layout to fix some Design Rule Check failures and extend the board to match the full layout of the original PCB. A few parts were replaced too, due to supply shortages. No functional changes were made.

2021-09-07

The rev4 board design is complete.

When I upgraded the 30-pin ribbon connector to one that fit better, it lowered the resistance to the LEDs. This caused me to burn the microcontroller on a test rev3 board by drawing too much current. So the question became: what values are appropriate for "maximum" brightness on both red and green. Today I found that, given a 5.15V VUSB, whatever resistance in the flex cable, and whatever voltage drop on the LEDs, 150 Ohms gives an even brightness on both red and green. Green draws about 15 mA and red about 10 mA, both within USB low-power spec and the current limits on the microcontroller.

I added an outputs directory containing the different revisions, and gerber files and drill files generated for either PCBWay or OSH Park.

The biggest challenge right now is the chip shortage. Even some of the capacitors I chose are out of stock. The hardest component to acquire is the ESD protection IC: USBLC6-2SC6. The USBLC6-4SC6 is available, but it would require some tweaking to the PCB layout.

On the software side of things, I added an internal ring buffer for debugging the debouncer. It can be dumped to the HID debug channel by holding both shifts and pressing H. I am trying to figure out why, with my custom low-latency debouncer, sometimes "the" comes out as "theb". For anyone that isn't trying to optimize latency as much as me, you can just run with the default QMK debouncer, which I've never seen produce phantom keys.

2021-05-02

One thing that annoyed me about the previous board design was that neither LED was hooked up to a PWM-capable pin and that the green one couldn't be driven, since it wants -5V. I want both lights to work and both to be dimmable.

Rev3 includes a charge pump to produce -5V and two MOSFETs that allow switching the green cathode with PWM.

I also figured out how the Fn switch works: it's a resistor divider that toggles 47K pull-down on a pin with a permanent 1M pull-up. Rev3 includes said 1M pull-up, so the firmware can read the Fn switch's state.

Sadly, it looks like there were many arrangements of media keys on the Sculpt over the years, and most of the media keys have nonsensical icons with behavior that differs on each platform. I'll try to make at least volume and play/pause work.

The parts for board rev 3 arrived last week. Some adjustments were required due to the chip shortage, but it's not too bad. The microcontroller is still available at least.

I attempted assembly of one, and it worked fine, but I screwed up the red and green pins, so I cut some traces and bodged in some kynar wire.

Both lights work!

I have not tested PWM. I did observe that twice as much current is being drawn for each light as I expected. I fear 40 mA could burn out the lights, so I plan to measure an appropriate series resistor this week. It's possible I never had this problem before because I was using a worse-fitting ribbon connector previously. In the past, I always measured 100 Ohms on every pin, but never tested the new ribbon connector.

Also, it kind of sucks that the LED brightness is a function of USB voltage (anywhere between 4.6 V and 5.25 V), but I don't want to include a regulator...

Assembly took about five hours for one board. A lot of that was getting my desk set up. I imagine I could do three boards in ... eight? I think if I used a stencil, hot air assembly could go pretty quickly. Especially if I had a preheater like the MHP30.

A couple people have suggested I set up an Etsy, but if I properly priced in hours of my labor, it would get prohibitive. And I don't want to deal with returns and warranties.

Remaining items before I can say the board is done:

  • Order a fourth PCB design with fixed green and red pins
  • Include an 0603 resistor on each
  • Fix the debouncer
  • Add a media key QMK layer, enabled with the Fn switch.

2021-04-27

In February, I tried pushing latency further than QMK offers out of the box. I switched from the default debouncer to sym_eager_pk, but since then I've observed some false keydowns and occasionally a phantom keypress. It's common for "the" to produce "theb". (Note that I use the Dvorak key layout.) I haven't looked at the matrix, but it's clear some debouncing is needed on keydown.

I'm planning on writing a custom debouncer that requires at least two frames for a keydown to register and at least 10 ms for a keyup. Having never done AVR optimization, I am trying to get a simavr benchmark harness up to make sure I don't regress the scan rate.

Parts

38
QtyValueFootprintReferences
4CL10A105KA8NNNCCapacitor_SMD:C_0603_1608MetricC4, C5, C6, C9
3CL10B104KB8NNNCCapacitor_SMD:C_0603_1608MetricC10, C11, C12
3ERJ-PA3F22R0VResistor_SMD:R_0603_1608MetricR1, R2, R7
2CL10C160JB8NNNCCapacitor_SMD:C_0603_1608MetricC7, C8
2ERJ-3EKF5101VResistor_SMD:R_0603_1608MetricR13, R14
2ERJ-3GEYJ331VResistor_SMD:R_0603_1608MetricR6, R10
2ERJ-PA3J151VResistor_SMD:R_0603_1608MetricR11, R12
2ERJ-PA3J472VResistor_SMD:R_0603_1608MetricR3, R8
12N7002BK,215Package_TO_SOT_SMD:SOT-23Q2
1AT90USB1286-AURPackage_QFP:TQFP-64_14x14mm_P0.8mmU3
1AVR-ISP-6 - NOT FITTEDConnector_IDC:IDC-Header_2x03_P2.54mm_VerticalJ3
1AlignmentHoleMountingHole:MountingHole_3mmH3
1BSS84AK,215Package_TO_SOT_SMD:SOT-23Q1
1CL21A475KOFNNNECapacitor_SMD:C_0805_2012MetricC1
1CL21B103KBANNNCCapacitor_SMD:C_0805_2012MetricC3
1CL21B104KACNNNCCapacitor_SMD:C_0805_2012MetricC2
1ERJ-3EKF8873VResistor_SMD:R_0603_1608MetricR4
1ERJ-PA3J473VResistor_SMD:R_0603_1608MetricR5
1EVQ-P7A01PButton_Switch_SMD:SW_SPST_EVQP7ASW1
1FFC3B07-30-TConnector_FFC-FPC:TE_3-84952-0_1x30-1MP_P1.0mm_HorizontalJ2
1LM2776DBVTPackage_TO_SOT_SMD:SOT-23-6U2
1MountingHoleNorthMountingHole:MountingHole_2.2mm_M2H1
1MountingHoleSouthMountingHole:MountingHole_2.2mm_M2H2
1TSX-3225 16.0000MF18X-AC0Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1USBLC6-2SC6Package_TO_SOT_SMD:SOT-23-6U1
1USB_C_ReceptacleConnector_USB:USB_C_Receptacle_Amphenol_12401610E4-2AJ1

Similar boards

  • 2 layers40 × 50 mmWired sculpt, the printed circuit board in 3D

    Wired sculpt

    chadaustin/wired-sculpt-pcb

    KiCad design files for the Wired Sculpt conversion mod

    39 parts35
  • 4 layers70 × 60 mmCAN Logger V2.0, the printed circuit board in 3D

    CAN Logger V2.0

    deep-th/CAN_Logger

    This is a compact and reliable CAN logger board built for automotive and industrial applications. It features the ESP32-S3 microcontroller and MCP25625 CAN controller with integrated transceiver, supporting two…

    138 parts3
  • 4 layers39.6 × 49.6 mmMS88SF3-ms keyboard, the printed circuit board in 3D

    MS88SF3-ms keyboard

    vsnrain/ms-keyboard

    Custom Microsoft Sculpt compatible board replacement using MS88SF3 NRF52840 microcontroller.

    69 parts2
  • 2 layers39.6 × 49.6 mmRp2040 stamp sculpt separated, the printed circuit board in 3D

    Rp2040 stamp sculpt separated

    techberet/msft_sculpt_rp2040_stamp_hw

    Lots of details available in my (rather long) blog post.

    8 parts9MIT
  • 4 layers110 × 64 mmSYCL Badge 2024, the printed circuit board in 3D

    SYCL Badge 2024

    ZigEmbeddedGroup/sycl-badge

    The badge for the SYCL conference! https://zigembeddedgroup.github.io/sycl-badge/

    145 parts39
  • 4 layers90.6 × 58.1 mmEcoApi pcb, the printed circuit board in 3D

    EcoApi pcb

    EcoApi/EcoApi_BeeHiveMonitoring

    describ options with 0R resistors. etc ...

    179 parts4GPL-3.0
  • 2 layers113 × 86.7 mmSiC based Battery Disconnect, the printed circuit board in 3D

    SiC based Battery Disconnect

    abhinav937/SiC-Based-Bi-Directional-Circuit-breaker

    KiCad 7 PCB design files for E_Fuse

    138 parts2

Questions

How big is the Wired sculpt PCB?

It measures 40 × 54 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Wired sculpt use?

38 parts, built around the AT90USB1286-AUR, USBLC6-2SC6, 2N7002BK,215-VB and BSS84AK,215(ES). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Wired sculpt KiCad files?

From the frgrw/reiyyeesr repository on GitHub, at the commit this page was made from: the board is wired-sculpt.kicad_pcb and its schematic wired-sculpt.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Wired sculpt design in my own project?

Its repository states no licence, so its author keeps all rights: ask frgrw before reusing the design.