Skip to the content
6 layers93 × 54.5 mmK3ng Rotator v2, the printed circuit board in 3D

Controller Board for K3NG Rotator Firmware - Based around Arduino Mega 2560

Size
93 × 54.5 mm
Copper layers
6
Thickness
1.6 mm
Parts
21
Nets
92
Pads
202
Tracks, vias
224, 19
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
30 Jun 2025
Updated
12 Jul 2025

Overview

K3ng Rotator v2 is an open-source printed circuit board by brokebit, from the brokebit/k3ng-Rotator-v2 repository on GitHub. It is a 6-layer board of 93 × 54.5 mm with 21 parts on 92 nets, routed with 224 tracks and 19 vias.

It is built around the DRV8871DDA. Its parts include 9 resistors, 4 capacitors, 2 ICs, 2 connectors and 1 diode. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

K3NG Rotator Controller

Schematic 3D Render

LCD2004 Connection

LCD Pin -> Rotator Pin

  1. 1 (GND) -> GND
  2. 2 (VCC) -> +5V
  3. 3 (Contrast) -> Center Pin (2) of Contrast Potentiometer
  4. 4 (Register Select) -> LCD_RST
  5. 5 (Read/Write) -> GND
  6. 6 (Enable) -> LCD_EN
  7. 7 (Data 0) -> NC
  8. 8 (Data 1) -> NC
  9. 9 (Data 2) -> NC
  10. 10 (Data 3) -> NC
  11. 11 (Data 4) -> LCD_D4
  12. 12 (Data 5) -> LCD_D5
  13. 13 (Data 6) -> LCD_D6
  14. 14 (Data 7) -> LCD_D7
  15. 15 (Backlight +) -> +5V + Contrast Potentiometer Pin 1
  16. 16 (Backlight -) -> GND + Contrast Potentiometer Pin 3

Parts

21
QtyValueFootprintReferences
610kResistor_SMD:R_1206_3216MetricR3, R4, R5, R6, R7, R8
2.1uF 50VCapacitor_SMD:C_1206_3216MetricC1, C3
218449221844922:PHOENIX_1844922J1, J2
222uf 63vfootprints:PCAP_EEHZ_D8_PANC2, C5
230kResistor_SMD:R_1206_3216MetricR1, R2
2DRV8871DDAPackage_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalViasU1, U2
2LOGOLOGOG***, G***
1330Resistor_SMD:R_1206_3216MetricR9
1Arduino_Mega2560_R3_Shieldarduino-library:Arduino_Mega2560_R3_ShieldA1
1LEDLED_SMD:LED_1206_3216MetricD1

Similar boards

  • 4 layers122.2 × 115.1 mmScan controller kicad, the printed circuit board in 3D

    Scan controller kicad

    fwachsmuth/Filmkorn-Raw-Scanner

    The Filmkorn Raw Scanner, turning 8mm and 16mm films into lossless 12-bit CinemaDNG

    170 parts13MIT
  • 4 layers81.3 × 52.8 mmGlue Board, the printed circuit board in 3D

    Glue Board

    arkorobotics/robocar-pinky

    DIY Robocar Project - Codename Pinky

    87 parts12
  • 2 layers65.6 × 56 mmWw2020, the printed circuit board in 3D

    Ww2020

    dkjonas/WildWillyHardware

    69 parts11
  • 4 layers50 × 50 mmSimpleboard, the printed circuit board in 3D

    Simpleboard

    AlessioMorale/unav2_hardware

    Initial test hardware for the future uNav board version

    122 parts5MIT
  • 2 layers83.3 × 56.5 mmPhone bell, the printed circuit board in 3D

    Phone bell

    purduehackers/phone-bell

    A Rotary Phone Doorbell

    53 parts4
  • 4 layers123 × 56 mmSkyduino Hardware, the printed circuit board in 3D

    Skyduino Hardware

    Skyduino/Skyduino-Hardware

    Hardware design files for the Skyduino roaster

    80 parts4
  • 4 layers31.3 × 34 mmNOGGIN, the printed circuit board in 3D

    NOGGIN

    berkeleyauv/RoboSub_HW

    PCB designs for Underwater Robotics at Berkeley (UR@B)

    60 parts3GPL-3.0
  • 2 layers93.1 × 158.3 mmMegaMouse, the printed circuit board in 3D

    MegaMouse

    KenwoodFox/MegaMouse

    MegaMouse! An atmega 328p powered micromouse!

    136 parts3MIT

Questions

How big is the K3ng Rotator v2 PCB?

It measures 93 × 54.5 mm and has 6 copper layers, 1.6 mm thick.

What parts does the K3ng Rotator v2 use?

21 parts, built around the DRV8871DDA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the K3ng Rotator v2 KiCad files?

From the brokebit/k3ng-Rotator-v2 repository on GitHub, at the commit this page was made from: the board is k3ng-Rotator-v2.kicad_pcb and its schematic k3ng-Rotator-v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the K3ng Rotator v2 design in my own project?

Its repository states no licence, so its author keeps all rights: ask brokebit before reusing the design.