

Afterglow
Pinball retro afterglow
- Size
- 128.6 × 81 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 203
- Nets
- 162
- Pads
- 677
- Tracks, vias
- 1,988, 170
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 Dec 2017
- Updated
- 9 Aug 2026
Overview
Afterglow is an open-source printed circuit board by bitfieldlabs, from the bitfieldlabs/afterglow repository on GitHub. It is a 2-layer board of 128.6 × 81 mm with 203 parts on 162 nets, routed with 1,988 tracks and 170 vias.
It is built around the RP2040, W25Q32JVSSIQ and 74LS165PC, with the ULN2803A, AO3400A and AO3401A among its other parts. Its parts include 96 resistors, 21 capacitors, 18 ICs, 18 diodes and 18 transistors. It belongs with the RP2040 boards of this library.
Main components
6RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH74LS165PC
DIP-160.4mA 0℃~+70℃ 105mW 35MHz 4.75V~5.25V 47ns@5V,50pF 8 8mA Asynchronous parallel load function Complementary Parallel-to-Serial DIP-16 Shift RegistersTexas InstrumentsShift RegistersULN2803A
SOP-18-300mil-40℃~+85℃ 0.93mA 100uA 15pF 20uA 30V 500mA 50V 8 SOP-18-300mil Darlington Transistor Arrays ROHSUMWDarlington Transistor ArraysAO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsAO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
README
README.mdAFTERGLOW is a pinball machine extension board that aims at softening the hard lamp on/off transitions which are the consequence of replacing the original incandescent bulbs with LEDs. Reproducing the original light effects is a big part of preserving a pinball game's nostalgia.
It currently works with Williams WPC, Williams System 11, Data East and probably also with Sega games. The basic principle involves resampling of the original lamp matrix signals at a higher frequency. This allows for PWM LED dimming with additional brightness steps.
The resampled signal is output via MOSFETs, allowing for direct connection of your pinball machine's lamp matrix.
Make sure to check the for detailed information and instructions.

While the effect is hard to catch on camera, this video gives an idea:
https://github.com/bitfieldlabs/afterglow/assets/999857/57093b11-0a40-46fb-a978-5d42df743db6
Licensing
Firmware and configuration software: Apache License 2.0
Hardware designs: CERN Open Hardware License - Permissive 2.0
See LICENSES/ for details
Licensing change
As of August 2026:
- Firmware and configuration software are licensed under Apache-2.0.
- Hardware designs are licensed under CERN-OHL-P-2.0.
All contributors with copyrightable contributions have consented to the relicensing, or their contributions have been replaced.
Quick guide to the board revisions
All in one
- PCB v3.0
This is the newest board built around the RP2040. Supports WPC, Data East, Sys11, Whitestar, S.A.M.
Supports hats, allowing for different ouput connectors, modding ports, displays etc.
Input protection using optocouplers.
Check the folder's readme for more details.
WPC, WPC-95, System 11, Data East, Sega
- PCB v1.3
This is the preferred board revision for these games.
Dedicated power input (+18V, Ground) must be connected separately to power driver board - PCB v1.4
Except for power input exactly the same as revision 1.3
+18V taken from column input.
⚠ Ground must still be connected to the PDB! Failure to do so will damage the board! - PCB v1.5
Same as v1.4, but using a one-sided PCB. This should be easier/cheaper for automated production than v1.4.
Stern Whitestar (and possibly S.A.M.)
- PCB v2.1 Dedicated board which will only work with Stern Whitestar and possibly S.A.M. games
Parts
203| Qty | Value | Footprint | References |
|---|---|---|---|
| 30 | 1k | Resistor_SMD:R_0402_1005Metric | R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25, R26 +14 |
| 22 | 10k | Resistor_SMD:R_0603_1608Metric | R47, R49, R51, R53, R55, R57, R59, R61, R82, R83, R84, R85, R86, R87, R88, R89 +6 |
| 13 | 100n | Capacitor_SMD:C_0402_1005Metric | C1, C2, C9, C11, C12, C13, C14, C15, C16, C17, C19, C20, C21 |
| 11 | 10k | Resistor_SMD:R_0402_1005Metric | R44, R63, R65, R67, R69, R71, R73, R75, R77, R79, R81 |
| 10 | 1k | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10 |
| 10 | 220 | Resistor_SMD:R_0603_1608Metric | R62, R64, R66, R68, R70, R72, R74, R76, R78, R80 |
| 10 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q9, Q10, Q11, Q12, Q13, Q14, Q15, Q16, Q17, Q18 |
| 10 | PC817 | Package_DIP:SMDIP-4_W9.53mm | U1, U2, U3, U4, U5, U6, U7, U8, U9, U10 |
| 10 | RB080 | Diode_SMD:D_SMA | D1, D2, D3, D4, D5, D6, D7, D8, D17, D18 |
| 8 | 2k | Resistor_SMD:R_0603_1608Metric | R46, R48, R50, R52, R54, R56, R58, R60 |
| 8 | 3.0V | Diode_SMD:D_SOD-323 | D9, D10, D11, D12, D13, D14, D15, D16 |
| 8 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | M3_1, M3_2, M3_3, M3_4 |
| 3 | 74LS165 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U14, U16, U17 |
| 3 | TestPoint | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP1, TP2, TP3 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C3, C10 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C7, C8 |
| 2 | 22p | Capacitor_SMD:C_0402_1005Metric | C4, C5 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R40, R41 |
| 2 | 5A SB | Fuse:Fuseholder_Clip-5x20mm_Schurter_OG_Lateral_P15.00x5.00mm_D1.3mm_Horizontal | F1, F2 |
| 2 | 5k1 | Resistor_SMD:R_0402_1005Metric | R37, R38 |
| 2 | Conn_01x10_Pin | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J4, J5 |
| 2 | Conn_02x03_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Vertical | J7, J8 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | PWR_LED1, ST_LED1 |
| 1 | afterglow:afterglow | afterglow | |
| 1 | 0.1 | Capacitor_SMD:C_0402_1005Metric | C18 |
| 1 | 136_OUT_C | Connector_Molex:Molex_KK-396_5273-03A_1x03_P3.96mm_Vertical | J13 |
| 1 | 200mOhm | Resistor_SMD:R_2512_6332Metric | R96 |
| 1 | 470uF | Capacitor_SMD:C_Elec_10x10.2 | C6 |
| 1 | CFG | Button_Switch_THT:SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mm | SW1 |
| 1 | Conn_01x04_Socket | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | Conn_Power | Connector_Molex:Molex_KK-396_5273-02A_1x02_P3.96mm_Vertical | J3 |
| 1 | Crystal_GND24_Small | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | INA181A1 | Package_TO_SOT_SMD:SOT-23-6 | U18 |
| 1 | J133_IN_R | Connector_Molex:Molex_KK-254_AE-6410-11A_1x11_P2.54mm_Vertical | J1 |
| 1 | J133_OUT_R | Connector_Molex:Molex_KK-254_AE-6410-09A_1x09_P2.54mm_Vertical | J9 |
| 1 | J134_OUT_R | Connector_Molex:Molex_KK-254_AE-6410-09A_1x09_P2.54mm_Vertical | J11 |
| 1 | J135_OUT_R | Connector_Molex:Molex_KK-254_AE-6410-09A_1x09_P2.54mm_Vertical | J14 |
| 1 | J137_IN_C | Connector_Molex:Molex_KK-396_5273-09A_1x09_P3.96mm_Vertical | J2 |
| 1 | J137_OUT_C | Connector_Molex:Molex_KK-396_5273-09A_1x09_P3.96mm_Vertical | J10 |
| 1 | J138_OUT_C | Connector_Molex:Molex_KK-396_5273-09A_1x09_P3.96mm_Vertical | J12 |
| 1 | LOGO | afterglow:bfl | G*** |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U12 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm_ThermalVias | U11 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_SKQG_WithStem | SW2 |
| 1 | ULN2803A | Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm | U13 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | P1 |
| 1 | W25Q32JVSS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U15 |
The 202 most common of 203 parts.
More from bitfieldlabs/afterglow
8- 2 layers128.7 × 81 mm

- 2 layers81 × 181.5 mm

- 2 layers116.5 × 81 mm

- 2 layers64.4 × 81 mm

- 2 layers193.5 × 80 mm

- 2 layers64.4 × 81 mm

- 2 layers64.4 × 81 mm

- 2 layers64.4 × 81 mm

Similar boards
- 2 layers100 × 100 mm

Flipdot Controller
Qeteshpony/Flipdot-Controller
Replacement controller for a Lawo Luminator Flipdot Display
58 parts2BSD-2-Clause - 2 layers130.5 × 75.3 mm

Console Interface
humanHardDrive/Gamecube-Controller-Wireless-Adapter
A wireless adapter for 4 Gamecube controllers
58 parts3MIT - 4 layers90 × 94 mm

- 2 layers151 × 95 mm

Deneme
g210101021/OpenStylophone-RP2040
Overview • Technical Summary • Architecture • Hardware Audit & Remediation • Schematic Subsystems • PCB Layout • Firmware Roadmap • Bill of Materials • Author
143 parts - 4 layers50 × 72.5 mm

- 4 layers98 × 124.4 mm

Piberry.beepy
CarbonComputers/Piberry-12
PiBerry v12 marks the final and most refined revision of the PiBerry handheld Linux terminal. Designed with both form and function in mind, this version brings together the best elements of previous iterations while…
132 parts9MIT - 2 layers84 × 98 mm

- 2 layers40 × 44 mm

Questions
How big is the Afterglow PCB?
It measures 128.6 × 81 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Afterglow use?
203 parts, built around the RP2040, W25Q32JVSSIQ, 74LS165PC and ULN2803A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Afterglow KiCad files?
From the bitfieldlabs/afterglow repository on GitHub, at the commit this page was made from: the board is afterglow_pcb_v30/afterglow.kicad_pcb and its schematic afterglow_pcb_v15/afterglow_nano_smd.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Afterglow design in my own project?
Its repository states no licence, so its author keeps all rights: ask bitfieldlabs before reusing the design.