

Falloutbadge
hackathon pcb badges
- Size
- 84 × 98 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 93
- Nets
- 107
- Pads
- 392
- Tracks, vias
- 617, 296
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 1 May 2026
- Updated
- 18 Sep 2026
Overview
Falloutbadge is an open-source printed circuit board by sophiayduan, from the sophiayduan/badges repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 84 × 98 mm with 93 parts on 107 nets, routed with 617 tracks and 296 vias.
It is built around the RP2040, CH592F and W25Q32JVSSIQ, with the AP2112K-3.3, TP4056-42-ESOP8 and USBLC6-2SC6 among its other parts. Its parts include 33 capacitors, 16 resistors, 8 switches, 6 ICs and 6 diodes. It belongs with the lEDs and displays boards and the RP2040 boards of this library.
Main components
10RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)CH592F
QFN-28(4x4)RF Transceiver ICsWCH (Nanjing Qinheng Microelectronics)W25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedTP4056-42-ESOP8
ESOP-8-40℃~+85℃ 1 1A 2uA 4.2V 4V~8V Charging IC Lithium Battery Support ESOP-8 Battery Management ROHSTOPPOWERBattery ManagementUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)MBR0530
SOD-1231 Independent 30V 5.5A 500mA 550mV@500mA 80uA@30V SOD-123 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky DiodesAO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsBLM18AG601SN1D
0603-55℃~+125℃ 1 380mΩ 500mA 600Ω@100MHz ±25% 0603 Ferrite Beads ROHSMurataFerrite BeadsSI1308EDL
SC-70-3-55℃~+150℃ 1 N-channel 1.4nC@10V 1.5A 1.5V 105pF 11pF 132mΩ@10V 23pF 30V 400mW N-Channel SOT-323 MOSFETs ROHSVishay IntertechnologyMOSFETs
README
README.mdPCB badges
Printed circuit board badges for Fallout's IRL event
we didn't end up using these - instead i ran a workshop for 180 students to make their own!
Features:
- RP2040 MCU - 2Mb Flash Memory
- 2.7" E-paper display
- Bluetooth Low Energy (BLE)
- Tactile Switches x8
- Standard Add-On* (1x6) pins
- Neopixels
- LIS2DH Accelerometer
I also made a version based around the STM32 w/ LoRa aswell, you can view it on the 'main' branch.
Parts
93| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0402_1005Metric | C3, C4, C5, C10, C11, C12, C13, C15, C16, C22, C41 |
| 10 | 1uF | Capacitor_SMD:C_0603_1608Metric | C28, C29, C30, C31, C32, C33, C34, C35, C36, C37 |
| 8 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10 |
| 3 | 10k | Resistor_SMD:R_0402_1005Metric | R2, R6, R11 |
| 3 | 330R | Resistor_SMD:R_0402_1005Metric | R1, R13, R14 |
| 3 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C24, C38, C40 |
| 3 | GND | TestPoint:TestPoint_Pad_D1.0mm | GND, GND, GND |
| 3 | MBR0530 | Diode_SMD:D_SOD-123 | D9, D10, D11 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R7 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric | C6, C8 |
| 2 | 27.4R | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | 33pF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 4.7uF | Capacitor_SMD:C_1206_3216Metric | C26, C27 |
| 2 | 4k7 | Resistor_SMD:R_0402_1005Metric | R16, R17 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R9, R10 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2_DIN965_Pad | H1, H2 |
| 1 | +3v3 | TestPoint:TestPoint_Pad_D1.0mm | +3V3 |
| 1 | +BATT | TestPoint:TestPoint_Pad_D1.0mm | +BATT |
| 1 | 0.47R | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 0.47uF | Capacitor_SMD:C_0402_1005Metric | C23 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C39 |
| 1 | 10uH | Inductor_SMD:L_1210_3225Metric | L1 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 2.2k | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C25 |
| 1 | 32MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | 68uH | Inductor_SMD:L_Changjiang_FNR6028S | L2 |
| 1 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | Antenna_Shield | antenna:ANT-F-1-2.4G-1.6mmFR4-WCH | AE2 |
| 1 | BLM18AG601SN1D | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | BOOTSEL | footprints:KEY-SMD_K2-1177SW-A4DW-06 | BOOTSEL |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_TDK_PS1240P02BT_D12.2mm_H6.5mm | BZ1 |
| 1 | CH592F | Package_DFN_QFN:WQFN-28-1EP_4x4mm_P0.4mm_EP2.7x2.7mm | U4 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | Conn_02x03 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | D | Diode_SMD:D_SOD-123F | D3 |
| 1 | E-INK | Connector_FFC-FPC:TE_2-1734839-4_1x24-1MP_P0.5mm_Horizontal | J3 |
| 1 | LiPo | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J4 |
| 1 | NOT RED | LED_SMD:LED_0603_1608Metric | D8 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D6 |
| 1 | RESET | footprints:KEY-SMD_K2-1177SW-A4DW-06 | RESET |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2 |
| 1 | Si1308EDL | Package_TO_SOT_SMD:SOT-323_SC-70 | Q2 |
| 1 | TP4056-42-ESOP8 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U6 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | VBUS | TestPoint:TestPoint_Pad_D1.0mm | +5V |
| 1 | W25Q32JVSS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U1 |
Similar boards
- 2 layers125 × 85 mm

- 2 layers80 × 50 mm

- 2 layers77 × 86.5 mm

- 2 layers60 × 150 mm

Phone
TheEinfachFelix/CampPhone
Warum habe ich mich dagegen entschieden, das Sim Modul selber zu implementieren? Ich habe kein Chip gefunden, der günstiger als das fertige Modul war, und ein Datenblatt in Englischer Sprache hat.
137 parts - 4 layers41.6 × 36 mm

Epaper smart watch
AeroX2/aerox2.github.io
One repository and npm installation builds the workshop at jamesridey.dev and the professional site at cv.jamesridey.dev.
102 parts - 2 layers90 × 57 mm

- 2 layers73.5 × 47.5 mm

- 4 layers64 × 43 mm

Dalws
anhldptit2610/dalws
This project is my attempt to learn about microcontroller and PCB design. Now I realize that making a full, complete electronic project is super hard.
83 parts2MIT
Questions
How big is the Falloutbadge PCB?
It measures 84 × 98 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Falloutbadge use?
93 parts, built around the RP2040, CH592F, W25Q32JVSSIQ and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Falloutbadge KiCad files?
From the sophiayduan/badges repository on GitHub, at the commit this page was made from: the board is hardware/falloutbadge.kicad_pcb and its schematic hardware/falloutbadge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Falloutbadge design in my own project?
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).