

Rp2040 badge
using rp2040
- Size
- 90 × 57 mm
- Copper layers
- 2
- Thickness
- 2.63 mm
- Parts
- 68
- Nets
- 78
- Pads
- 246
- Tracks, vias
- 518, 71
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 27 Sep 2025
- Updated
- 13 Oct 2025
Overview
Rp2040 badge is an open-source printed circuit board by krVishesh, from the krVishesh/ePaper_badge repository on GitHub. It is a 2-layer board of 90 × 57 mm with 68 parts on 78 nets, routed with 518 tracks and 71 vias.
It is built around the RP2040, W25Q128JVSIQ and AP7361C-33E, with the USBLC6-2SC6, MBR0530 and SI1308EDL among its other parts. Its parts include 26 capacitors, 11 resistors, 5 diodes, 4 ICs and 2 connectors. It belongs with the lEDs and displays boards and the RP2040 boards of this library.
Main components
6RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAP7361C-33E
SOT-223-40℃~+85℃@(Ta) 1 1A 3.3V 340mV@(1A) 6V 75dB@(1kHz) 80uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)MBR0530
SOD-1231 Independent 30V 5.5A 500mA 550mV@500mA 80uA@30V SOD-123 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky DiodesSI1308EDL
SC-70-3-55℃~+150℃ 1 N-channel 1.4nC@10V 1.5A 1.5V 105pF 11pF 132mΩ@10V 23pF 30V 400mW N-Channel SOT-323 MOSFETs ROHSVishay IntertechnologyMOSFETs
Parts
68| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C17, C18, C20, C21, C22, C23, C24, C25, C26 |
| 8 | 1uF/25V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C4, C5, C6, C7, C8, C10 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R9, R10 |
| 3 | MBR0530 | Diode_SMD:D_SOD-123 | D1, D2, D3 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C19, C27 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R6 |
| 2 | 30pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C15, C16 |
| 2 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13, C14 |
| 2 | 4.7uF/25V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C9, C11 |
| 2 | 470R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R11, R12 |
| 2 | 5k1 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R8 |
| 2 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP3, TP6 |
| 2 | POW_LED | Diode_SMD:D_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4, D5 |
| 2 | SCL | TestPoint:TestPoint_Pad_D1.5mm | SCL0, SCL1 |
| 2 | SDA | TestPoint:TestPoint_Pad_D1.5mm | SDA0, SDA1 |
| 1 | +3V3 | TestPoint:TestPoint_Pad_D1.5mm | TP10 |
| 1 | +5V | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 12mHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSoldering | Y1 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 2R2 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 47uH 500mA | Inductor_SMD:L_Sunlord_SWPA5040S | L1 |
| 1 | AP7361C-33E | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_PTS647_Sx38 | SW2 |
| 1 | BS | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP2 |
| 1 | Conn_01x24 | Connector_FFC-FPC:Jushuo_AFC07-S24FCA-00_1x24-1MP_P0.50_Horizontal | J1 |
| 1 | DEBUG_EN | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | PTC 750mA | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | RST | Button_Switch_SMD:SW_SPST_PTS647_Sx38 | SW3 |
| 1 | RX | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | SWD | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | Si1308EDL | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q1 |
| 1 | TX | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U4 |
Similar boards
- 4 layers74.1 × 130 mm

- 4 layers45 × 69 mm

OpenVault
NoctaLabs-Sh/Nocta-One-Hardware
Open hardware for the Nocta vault: an offline password manager with a 2.7 inch e-ink screen. KiCad schematic, board layout, gerbers and BOM. CERN-OHL-S v2.
64 parts1CERN-OHL-S-2.0 - 2 layers80 × 50 mm

- 2 layers84 × 98 mm

- 2 layers73.5 × 47.5 mm

- 2 layers70 × 119.5 mm

UHBadge
gianluca-rainis/UHBadge
Universal Hacker Badge - The ultimate badge for hackers.
121 parts2CERN-OHL-S-2.0 - 2 layers137.9 × 57.6 mm

- 2 layers77 × 86.5 mm

Questions
How big is the Rp2040 badge PCB?
It measures 90 × 57 mm and has 2 copper layers, 2.63 mm thick.
What parts does the Rp2040 badge use?
68 parts, built around the RP2040, W25Q128JVSIQ, AP7361C-33E and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rp2040 badge KiCad files?
From the krVishesh/ePaper_badge repository on GitHub, at the commit this page was made from: the board is rp2040_badge.kicad_pcb and its schematic rp2040_badge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rp2040 badge design in my own project?
Its repository states no licence, so its author keeps all rights: ask krVishesh before reusing the design.