2 layers32 × 150 mm
Led tube
janekc/led-tube
It should run with 4 x 18650 lithium battery cells, that can be recharged through USB Power Delivery 3.0 with up to 18W.
65 partsCERN-OHL-P-2.0
4 layers74.1 × 130 mm
Badge secsea V1 1
cchaloin/HIP_SecSeaHack In Provence badge for SecSea
- Size
- 74.1 × 130 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 132
- Nets
- 122
- Pads
- 486
- Tracks, vias
- 1,007, 420
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 14 Jan 2026
- Updated
- 14 Jan 2026
Overview
Badge secsea V1 1 is an open-source printed circuit board by cchaloin, from the cchaloin/HIP_SecSea repository on GitHub. It is a 4-layer board of 74.1 × 130 mm with 132 parts on 122 nets, routed with 1,007 tracks and 420 vias.
It is built around the RP2040, CC1101RGPR and LM321, with the W25Q128JVSIQ, 74HC139D and TP4056 among its other parts. Its parts include 44 capacitors, 35 resistors, 9 diodes, 7 ICs and 7 switches. It belongs with the lEDs and displays boards and the RP2040 boards of this library.
Main components
12
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
CC1101RGPR
QFN-20-EP(4x4)-112dBm -40℃~+85℃ 1.8V~3.6V 12dBm 15.7mA 300MHz~348MHz、387MHz~464MHz、779MHz~928MHz 315MHz、433MHz、868MHz、915MHz 34.2mA 500Kbps ISM Power-on reset function、Supports RSSI function、CRC check function、Input sync word detection function SPI transceiver QFN-20-EP(4x4) RF Transceiver ICs ROHSTexas InstrumentsRF Transceiver ICs
LM321
SOT-23-50℃~+70℃ 1 2mV 3nA 400V/ms 40mA 430uA 45nA 90dB SOT-23-5 Operational Amplifier ROHSPJSEMIOperational Amplifier
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
74HC139D
SO-16-40℃~+125℃ 11ns@6.0V,50pF 160uA 2/4 2V~6V 74HC Decoder Single Supply SOIC-16 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches / Encoders & Decoders / Multiplexers
TP4056
ESOP-8-40℃~+85℃ 1 1A 35uA 4.2V 4V~6.5V Charging IC Lithium Battery Support Support 恒流充电、恒压充电、涓流充电、自动再充电、充电终止、可编程充电电流、软启动、欠压锁定 ESOP-8 Battery Management ROHSUMWBattery Management
TPS63000DRC
UncategorisedTexas Instruments
MBR0530
SOD-1231 Independent 30V 5.5A 500mA 550mV@500mA 80uA@30V SOD-123 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky Diodes
K2-1112SW-A4SW-04
弯插,7x3.5mm-25℃~+85℃ 100,000 cycles 12V 2.5N 3.5mm 3.95mm 50mA 7mm Rectangular Button Right Angle SPST 弯插,7x3.5mm Tactile Switches ROHSHRO ElectronicsTactile Switches
PM254-2-06-S-8.5
SMD,P=2.54mm-40℃~+105℃ 12P 2 2.54mm 2.54mm 2x6P 3A 8.5mm Copper alloy Square Hole Surface Mount,Vertical Top SMD,P=2.54mm Female Headers ROHSHCTLFemale Headers
TS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile Switches
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.mdHIP_SecSea
Hack In Provence badge for SecSea
Parts
132| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 100nf | Capacitor_SMD:C_0402_1005Metric | C1, C2, C3, C4, C5, C6, C7, C8, C12, C15, C16, C19, C20, C42, C43, C44 +1 |
| 8 | 10K | Resistor_SMD:R_0402_1005Metric | R4, R10, R11, R12, R13, R17, R22, R23 |
| 8 | 1uf | Capacitor_SMD:C_0805_2012Metric | C29, C30, C31, C32, C33, C34, C35, C36 |
| 6 | 100K | Resistor_SMD:R_0402_1005Metric | R7, R9, R24, R26, R31, R35 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP3, TP4, TP5 |
| 4 | MBR0530 | Diode_SMD:D_SOD-123 | D2, D3, D4, D5 |
| 3 | 1K | Resistor_SMD:R_0402_1005Metric | R3, R8, R16 |
| 3 | 27nH | Inductor_SMD:L_0402_1005Metric | L1, L2, L4 |
| 3 | 4.7K | Resistor_SMD:R_0402_1005Metric | R32, R33, R34 |
| 3 | 47uf | Capacitor_SMD:C_0805_2012Metric | C39, C40, C41 |
| 3 | ADC-VBAT | TestPoint:TestPoint_Pad_D1.5mm | TP8, TP9, TP10 |
| 2 | 10uf | Capacitor_SMD:C_0805_2012Metric | C37, C38 |
| 2 | 15pf | Capacitor_SMD:C_0402_1005Metric | C10, C11 |
| 2 | 1uf | Capacitor_SMD:C_0402_1005Metric | C13, C14 |
| 2 | 220pf | Capacitor_SMD:C_0402_1005Metric | C21, C26 |
| 2 | 27R4 | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 27pf | Capacitor_SMD:C_0402_1005Metric | C17, C18 |
| 2 | 2K4 | Resistor_SMD:R_0402_1005Metric | R19, R27 |
| 2 | 3.9pf | Capacitor_SMD:C_0402_1005Metric | C22, C23 |
| 2 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C27, C28 |
| 2 | 5K1 | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 2 | K2-1112SW-A4SW-04 | Partek Library:K2-1112SW-A4SW-04 | SW2, SW3 |
| 2 | PM254-2-06-S-8.5 | Connector_PinSocket_2.54mm:PinSocket_2x06_P2.54mm_Vertical_SMD | J2, J3 |
| 2 | TS-1187A-B-A-B | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW1, SW6 |
| 2 | WS2812B | LED_SMD:LED_WS2812B-2020_PLCC4_2.0x2.0mm | LED1, LED2 |
| 2 | XDTD-6650 | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | SW4, SW5 |
| 1 | 0R1 | Resistor_SMD:R_1206_3216Metric | R20 |
| 1 | 1.2K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21 |
| 1 | 100R | Resistor_SMD:R_0402_1005Metric | R30 |
| 1 | 10uH 1A | Inductor_SMD:L_Ferrocore_DLG-0403 | L6 |
| 1 | 178K | Resistor_SMD:R_0402_1005Metric | R29 |
| 1 | 1M | Resistor_SMD:R_0402_1005Metric | R28 |
| 1 | 1N4148 | Diode_SMD:D_SOD-123 | D1 |
| 1 | 2.2µH | Inductor_SMD:L_APV_ANR4012 | L7 |
| 1 | 200K | Resistor_SMD:R_0402_1005Metric | R25 |
| 1 | 22nH | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 26MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | X2 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | 330R | Resistor_SMD:R_0402_1005Metric | R14 |
| 1 | 3R | Resistor_SMD:R_0402_1005Metric | R18 |
| 1 | 5.6pf | Capacitor_SMD:C_0402_1005Metric | C25 |
| 1 | 56K | Resistor_SMD:R_0402_1005Metric | R15 |
| 1 | 74HC139 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | 8.2pf | Capacitor_SMD:C_0402_1005Metric | C24 |
| 1 | ABM8-272-T3 | Crystal:Crystal_SMD_Abracon_ABM8AIG-4Pin_3.2x2.5mm | X1 |
| 1 | ACAG1204-433-T | Partek Library:ANT-SMD_L12.0-W4.0_ACAG1204-915-T | L5 |
| 1 | AFC07-S24ECA-00 | Partek Library:FPC_24 | J4 |
| 1 | CC1101RGPR | Partek Library:QFN-20-1EP_L4.0-W4.0-P0.5-EP2.4 | U4 |
| 1 | Green | LED_SMD:LED_0603_1608Metric | D7 |
| 1 | LM321 | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | LOGO | Partek Library:silkscreen_cigale | G1 |
| 1 | LedGND | TestPoint:TestPoint_Pad_D1.5mm | TP7 |
| 1 | LedOut | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | MLT-8530 | Partek Library:Buzzer MLT-8530 | BUZZER1 |
| 1 | Micro_SD_Card_Det1 | Partek Library:MicroSD TF-115-BCP9 | J5 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | Red | LED_SMD:LED_0603_1608Metric | D6 |
| 1 | SI1308EDL | Package_TO_SOT_SMD:SOT-323_SC-70 | Q2 |
| 1 | SI2301 | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | SW_SPDT | Partek Library:SPDT SMD slide switch | SW7 |
| 1 | TP4056 | Partek Library:ESOP-8_L4.9-W3.9-P1.27-LS6.0-BL-EP | U5 |
| 1 | TPS63000 | Package_SON:Texas_DRC0010J | U6 |
| 1 | USB_C_Receptacle_USB2.0_14P | Partek Library:USB-C_C165948 | J1 |
| 1 | W25Q128JVSIQ | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U3 |
| 1 | WAFER-PH2.0-2PWB | Partek Library:CONN-SMD_2P-P2.00_XUNPU_WAFER-PH2.0-2PWB | H1 |
Similar boards
- 2 layers68 × 42 mm
- 4 layers152.4 × 63.5 mm
- 2 layers83.7 × 53.7 mm
- 6 layers85.6 × 33.7 mm
IWR AOP MODULE
l3wi/IWR-AOP-MODULE
60 GHz mmWave radar module built around TI's IWR6843AOP: USB-C or carrier-socket operation. KiCad 10, JLCPCB-ready.
158 parts4MIT - 4 layers39.3 × 29 mm
- 2 layers52 × 50.5 mm
- 4 layers45 × 32 mm
Templog mainboard
Michael-Manning/E-Paper-Climate-Logger
Firmware, PCB, and enclosure for the Weathergotchi E-Paper climate logger.
68 parts457MIT
Questions
How big is the Badge secsea V1 1 PCB?
It measures 74.1 × 130 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Badge secsea V1 1 use?
132 parts, built around the RP2040, CC1101RGPR, LM321 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Badge secsea V1 1 KiCad files?
From the cchaloin/HIP_SecSea repository on GitHub, at the commit this page was made from: the board is badge_secsea_V1_1.kicad_pcb and its schematic badge_secsea_V1_1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Badge secsea V1 1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask cchaloin before reusing the design.