2 layers50 × 50 mm
Controller Interface
humanHardDrive/Gamecube-Controller-Wireless-Adapter
A wireless adapter for 4 Gamecube controllers
56 parts3MIT
2 layers130.5 × 75.3 mm
Console Interface
humanHardDrive/Gamecube-Controller-Wireless-Adapter3A wireless adapter for 4 Gamecube controllers
- Size
- 130.5 × 75.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 67
- Pads
- 236
- Tracks, vias
- 71, 4
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 2 Mar 2024
- Updated
- 19 Sep 2026
Overview
Console Interface is an open-source printed circuit board by humanHardDrive, from the humanHardDrive/Gamecube-Controller-Wireless-Adapter repository on GitHub, published under the MIT licence. It is a 2-layer board of 130.5 × 75.3 mm with 58 parts on 67 nets, routed with 71 tracks and 4 vias.
It is built around the RP2040, W25Q32JVSSIQ and MIC5504-3.3YM5, with the AO3401A among its other parts. Its parts include 18 capacitors, 13 resistors, 9 diodes, 5 ICs and 5 connectors. It belongs with the interfaces and adapters boards and the RP2040 boards of this library.
Main components
4
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
MIC5504-3.3YM5
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 15uA 180mV@(300mA) 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
AO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
README
README.mdGameCube Wireless Controller Hub
The GameCube Wireless Controller hub allows 4 GameCube controllers to be made wireless to any GameCube controller interface. The hub functions in two halves, one to connect to the controllers, and one to connect to the console. Both halves are based on the RP2040 microcontroller and the NRF24l01 transceiver and share the same source code.
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100n | Capacitor_SMD:C_0603_1608Metric | C2, C5, C6, C8, C10, C11, C12, C13, C14 |
| 7 | 100 | Resistor_SMD:R_0603_1608Metric | R6, R8, R11, R12, R13, R16, R17 |
| 7 | LED | LED_SMD:LED_0603_1608Metric | D1, D4, D5, D6, D7, D8, D9 |
| 4 | C | Capacitor_SMD:C_0603_1608Metric | C15, C16, C19, C20 |
| 4 | Conn_01x04_Socket | Connector_JST:JST_GH_BM05B-GHS-TBT_1x05-1MP_P1.25mm_Vertical | J2, J3, J4, J6 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 2u2 | Capacitor_SMD:C_0603_1608Metric | C1, C7, C9 |
| 2 | 15p | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | 5K1 | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | D_Schottky | Diode_SMD:D_0603_1608Metric | D2, D3 |
| 2 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U4, U5 |
| 1 | 10K | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2 |
| 1 | SW_BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | SW_PAIR | Button_Switch_SMD:Panasonic_EVQPUK_EVQPUB | SW3 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | W25Q32JVSS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |
| 1 | ~ | GTS24:GTS24-SMD | U3 |
More from humanHardDrive/Gamecube-Controller-Wireless-Adapter
2- 2 layers50 × 50 mm
Controller Interface LB
humanHardDrive/Gamecube-Controller-Wireless-Adapter
A wireless adapter for 4 Gamecube controllers
19 parts3MIT
Similar boards
- 4 layers99.1 × 83.8 mm
Ibm-5151-pcb
asinghani/ibm-5151-controller
Building a VT100 emulator out of an IBM 5151 monitor and an FPGA
85 partsMIT - 4 layers110 × 120 mm
DUT Interface board v0.2
krishchan007/DUT_Interface_board_v0.2
v0.2 of DUT interface board with significant changes in layout, architecture etc.
271 parts1 - 2 layers128.6 × 81 mm
- 4 layers90 × 94 mm
- 2 layers151 × 95 mm
Deneme
g210101021/OpenStylophone-RP2040
Overview • Technical Summary • Architecture • Hardware Audit & Remediation • Schematic Subsystems • PCB Layout • Firmware Roadmap • Bill of Materials • Author
143 parts - 4 layers50 × 72.5 mm
- 2 layers120 × 130 mm
SingularitySurfer V1
nkrackow/SingularitySurfer-FPGA-Lock-In-Amplifier
Repository for the development of an FPGA based DSP Lock-In Amplifier
174 parts80MIT - 2 layers25.6 × 0 mm
Questions
How big is the Console Interface PCB?
It measures 130.5 × 75.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Console Interface use?
58 parts, built around the RP2040, W25Q32JVSSIQ, MIC5504-3.3YM5 and AO3401A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Console Interface KiCad files?
From the humanHardDrive/Gamecube-Controller-Wireless-Adapter repository on GitHub, at the commit this page was made from: the board is Layout/Console Interface/Console Interface.kicad_pcb and its schematic Layout/Console Interface/Console Interface.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Console Interface design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).