

Bio Data Bridge
Bio-Data-Bridge, insan vücudundan alınan hassas biyometrik sinyalleri (EKG, EMG veya diğer analog veriler) güvenli bir şekilde işlemek ve dijital ortama aktarmak için tasarlanmış, yüksek izolasyonlu bir Biyometrik Veri Arayüzüdür
- Size
- 109.9 × 32.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 35
- Nets
- 58
- Pads
- 146
- Tracks, vias
- 285, 32
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 8 Apr 2026
- Updated
- 8 Apr 2026
Overview
Bio Data Bridge is an open-source printed circuit board by bgmbzk, from the bgmbzk/Bio-Data-Bridge-v1.0 repository on GitHub. It is a 2-layer board of 109.9 × 32.7 mm with 35 parts on 58 nets, routed with 285 tracks and 32 vias.
It is built around the ATMEGA328P-AU, CH340G and LM358, with the L7805 among its other parts. Its parts include 11 capacitors, 10 resistors, 6 ICs, 2 diodes and 2 connectors. It belongs with the interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
4ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)CH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersLM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierL7805
TO-220ST0℃~+125℃@(Tj) 1 1.2A 20V 2V@(1A) 42uV 500uA 5V 73dB@(120Hz) Fixed Positive Short Circuit Protection TO-220ST Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSOSENVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdBio-Data-Bridge v1.0 🩺💻
Bio-Data-Bridge, insan vücudundan alınan hassas biyometrik sinyalleri (EKG, EMG veya diğer analog veriler) güvenli bir şekilde işlemek ve dijital ortama aktarmak için tasarlanmış, yüksek izolasyonlu bir Biyometrik Veri Arayüzüdür.

🚀 Projenin Amacı ve Kapsamı
Bu projenin temel odağı, insan vücudundan gelen mikrovolt seviyesindeki zayıf analog sinyallerin, dış gürültüden arındırılarak ve elektriksel güvenlikten ödün vermeden bilgisayara aktarılmasıdır.
- İnsan-Makine Arayüzü (HMI): Kart üzerindeki özel konnektör yapısı, elektrotlar aracılığıyla doğrudan insan vücudundan veri alacak şekilde konfigüre edilmiştir.
- Kullanıcı Güvenliği: Kullanıcı ile doğrudan fiziksel temas olduğu için sistem, PC817 optokuplörler kullanılarak bilgisayarın şebeke geriliminden ve olası voltaj dalgalanmalarından tamamen izole edilmiştir.
🛠 Teknik Sinyal Hattı (Signal Chain)
- Veri Toplama: İnsan vücudundan gelen analog sinyaller ana giriş konnektörü üzerinden sisteme dahil olur.
- Sinyal İşleme: Mikrovolt seviyesindeki veriler, LM358 Op-Amp katmanında filtrelenir ve işlenebilir seviyeye yükseltilir.
- İzolasyon ve Aktarım: İşlenen veri, elektriksel izolasyon bariyerini geçerek CH340G USB-UART köprüsü üzerinden bilgisayara iletilir.
- Kontrol: Tüm süreç endüstri standardı ATmega328P mikrodenetleyicisi tarafından yönetilir.

📐 PCB Tasarım Özellikleri
- Güvenlik Odaklı Layout: İzolasyon bariyeri (Clearance/Creepage), kullanıcı güvenliğini en üst düzeyde tutacak şekilde tasarlanmıştır.
- Özel Geometri: Ergonomik kullanım ve estetik bir görünüm için özel pahlı (chamfered) kenar kesimi uygulanmıştır.
- Sinyal Bütünlüğü: Hassas analog hatlar, dijital gürültüden (EMI) korunması için PCB üzerinde optimize edilmiştir.
- GND Copper Pour (Topraklama Alanı): Sinyal bütünlüğünü artırmak ve gürültüyü minimize etmek amacıyla PCB'nin hem ön (F.Cu) hem de arka (B.Cu) yüzeyine geniş bakır alanlar (Copper Pour) eklenerek tüm toprak hatları optimize edilmiştir.

📁 Klasör İçeriği & Dokümantasyon
/Gerbers: Fabrikasyon için hazır üretim (Gerber & Drill) dosyaları./Schematic: Devre şeması ve tasarım detayları.Bio-Data-Bridge.csv(BOM Listesi): Projenin montajı için gereken tüm elektronik bileşenlerin (direnç, kapasitör, IC vb.) tam listesi, değerleri ve kılıf (footprint) bilgileri.Bio-Data-Bridge.png: Kartın 3D render görseli.
🛠 Kurulum ve Üretim
- PCB Üretimi:
Gerberklasöründeki dosyaları herhangi bir PCB üreticisine gönderin. - Malzeme Tedariği:
Bio-Data-Bridge.csvdosyasını açarak gerekli tüm parçaları (BOM listesi) temin edin. - Montaj: Şematik ve PCB layout takibiyle bileşenleri lehimleyin.
- Veri Akışı: USB üzerinden bağlantı kurarak biyometrik veri akışını izlemeye başlayın.
Bu proje KiCad 8.0 kullanılarak geliştirilmiştir.
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100nF | Capacitor_SMD:C_0805_2012Metric | C3, C4, C5, C11 |
| 4 | 22pF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C8, C9 |
| 2 | 10k | Resistor_SMD:R_0805_2012Metric | R9, R10 |
| 2 | 220 | Resistor_SMD:R_0805_2012Metric | R7, R8 |
| 2 | 220Ω | Resistor_SMD:R_0805_2012Metric | R5, R6 |
| 2 | 5.1kΩ | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1, Y2 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D1, D2 |
| 2 | PC817 | Package_DIP:SMDIP-4_W7.62mm | U3, U4 |
| 1 | 10UF | Capacitor_SMD:C_0805_2012Metric | C7 |
| 1 | 10kΩ | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10nF | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 1MΩ | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | ATmega328P-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Battery_Cell | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | BT1 |
| 1 | CH340G | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U6 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1 |
| 1 | L7805 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | LM358 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | Thermistor_PTC | Fuse:Fuse_0805_2012Metric | TH1 |
| 1 | USB_C_Receptacle | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
Similar boards
- 2 layers50.5 × 128.5 mm

- 2 layers60 × 50 mm

Vx8 gps prototype v2.0
4x1md/vx8_gps
DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.
56 parts66MIT - 2 layers120 × 70 mm

BRNG
valerionew/Banana-Random-Number-Generator
Random number generator based on radioactivity from bananas
93 parts37 - 4 layers50 × 50 mm

DUINO
elVucko/Duino_Coin_AVR
This is the simplest DUINO coin mining board design with four Atmega328p and CH340 connected to the FE1.1S USB hub.
93 parts7MIT - 4 layers90 × 43 mm

Temperature Thing With Thermocouple 3V3
spacebiz24/Thermal-Profiling
A Thermal Profiling Platform built with ATMega328P and MAX31856
89 parts3MPL-2.0 - 4 layers102 × 49 mm

CURSO PCB DRONE
ArduProject/PCB_DRONE_C8
En este repositorio encontrareis los archivos de fabricación y las listas de montaje del PCB con STM32F103C8 que hemos visto en el curso.
153 parts1MIT - 2 layers58.5 × 40.6 mm

Placa
ArthurMLago/botwJoystickGyro
Making any controller have motion controls or use with CEMU
81 parts1 - 2 layers25 × 99 mm

Cremini blade atmega328p
nicklasfrahm/mykilio
Mykilio is the proposal for a new Living Standard with the goal to reimagine infrastructure management and monitoring.
102 parts1MIT
Questions
How big is the Bio Data Bridge PCB?
It measures 109.9 × 32.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Bio Data Bridge use?
35 parts, built around the ATMEGA328P-AU, CH340G, LM358 and L7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bio Data Bridge KiCad files?
From the bgmbzk/Bio-Data-Bridge-v1.0 repository on GitHub, at the commit this page was made from: the board is Bio-Data-Bridge.kicad_pcb and its schematic Bio-Data-Bridge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bio Data Bridge design in my own project?
Its repository states no licence, so its author keeps all rights: ask bgmbzk before reusing the design.