

PantoGraph
- Size
- 43 × 44 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 71
- Nets
- 40
- Pads
- 357
- Tracks, vias
- 302, 51
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 7 Mar 2023
- Updated
- 20 May 2026
Overview
PantoGraph is an open-source printed circuit board by bask185, from the bask185/Train-Science-DIY repository on GitHub. It is a 4-layer board of 43 × 44 mm with 71 parts on 40 nets, routed with 302 tracks and 51 vias.
It is built around the ATTINY1616-MN and 1N4148WS. Its parts include 30 resistors, 12 capacitors, 7 connectors, 5 ICs and 4 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATTINY1616-MN
QFN-20-EP(3x3)-40℃~+105℃ 1.8V~5.5V 10bit 16KB 18 20MHz 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH QFN-20-EP(3x3) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes
Parts
71| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100k | Resistor_SMD:R_0402_1005Metric | R401, R401, R401, R402, R402, R402, R405, R405, R405 |
| 9 | R_Small | Resistor_SMD:R_0402_1005Metric | R403, R403, R403, R404, R404, R404, R408, R408, R408 |
| 8 | 100nF | Capacitor_SMD:C_0402_1005Metric | C201, C302, C401, C401, C401, C403, C403, C403 |
| 6 | 1R | Resistor_SMD:R_0402_1005Metric | R406, R406, R406, R407, R407, R407 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric | R302, R409, R409, R409 |
| 4 | 1N4148WS | Diode_SMD:D_SOD-323 | D301, D302, D303, D304 |
| 3 | 220nF | Capacitor_SMD:C_0603_1608Metric | C402, C402, C402 |
| 3 | Conn_01x01_Pin | Connector_Wire:SolderWirePad_1x01_SMD_1x2mm | J101, J102, J103 |
| 3 | FFC | Connector_FFC-FPC:Hirose_FH12-12S-0.5SH_1x12-1MP_P0.50mm_Horizontal | J108, J108, J108 |
| 3 | ~ | custom_kicad_lib_sk:a4988 | U401, U401, U401 |
| 1 | 26k | Resistor_SMD:R_0402_1005Metric | R301 |
| 1 | 330nF | Capacitor_SMD:C_0402_1005Metric | C301 |
| 1 | ATtiny1616-M | custom_kicad_lib_sk:VQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mm | U201 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J201 |
| 1 | L78L05_SOT89 | Package_TO_SOT_SMD:SOT-89-3 | U301 |
| 1 | PhoenixContact_MC_1,5_3-G-3.5_1x03_P3.50mm_Horizontal | Connector_Phoenix_MC:PhoenixContact_MC_1,5_3-G-3.5_1x03_P3.50mm_Horizontal | RELAY |
| 1 | R | Resistor_SMD:R_0402_1005Metric | R201 |
The 59 most common of 71 parts.
More from bask185/Train-Science-DIY
12- 2 layers75 × 106.5 mm

- 2 layers68.5 × 130.5 mm

- 2 layers153.2 × 127.5 mm

- 2 layers54.5 × 73 mm

- 2 layers99.5 × 61 mm

- 4 layers70 × 83.5 mm

- 2 layers105.5 × 63.5 mm

- 2 layers78 × 58.5 mm

- 2 layers83.5 × 50.3 mm

- 2 layers81 × 71.2 mm

- 2 layers54 × 94.5 mm

- 2 layers100 × 45 mm

Similar boards
- 4 layers62.1 × 83.8 mm

Ss main board
loopj/short-stack
World's Smallest Nintendo Wii, using a trimmed motherboard and custom stacked PCBs
69 parts804 - 2 layers80 × 50 mm

- 4 layers100 × 68 mm

- 2 layers56.9 × 23.6 mm

Hexagon
kieraneglin/hexagon-art
A passive breakout board: two lever-terminal inputs, three JST XH outputs, all six conductors (RX bus, two spares, +12V, GND, +5V) paralleled straight across. No active components, no regulation, nothing to configure.
24 parts19 - 4 layers44.5 × 44.5 mm

Flashlight
engineerbo/flashlight-dev-hw
This repository contains design files for the development board for a flashlight boost driver. The test firmware can be found in the firmware repository.
73 parts15MIT - 2 layers29 × 36 mm

Flux Capacitor Micro Pin Badge
hojadurdy/Flux_Capacitor_Micro
A tiny (36mm x 29mm) pin badge and keychain PCB version of Flux Capacitor featuring 25 animated LEDs that animate to create the “fluxxing” effect.
48 parts6 - 4 layers50.3 × 21.5 mm

- 2 layers25.4 × 52 mm

Questions
How big is the PantoGraph PCB?
It measures 43 × 44 mm and has 4 copper layers, 1.6 mm thick.
What parts does the PantoGraph use?
71 parts, built around the ATTINY1616-MN and 1N4148WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PantoGraph KiCad files?
From the bask185/Train-Science-DIY repository on GitHub, at the commit this page was made from: the board is PCB_SOURCE/pantoGraph/pantoGraph.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the PantoGraph design in my own project?
Its repository states no licence, so its author keeps all rights: ask bask185 before reusing the design.