

SingleServoDriver
- Size
- 43 × 35 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 19
- Nets
- 29
- Pads
- 79
- Tracks, vias
- 2, 0
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 7 Mar 2023
- Updated
- 20 May 2026
Overview
SingleServoDriver is an open-source printed circuit board by bask185, from the bask185/Train-Science-DIY repository on GitHub. It is a 2-layer board of 43 × 35 mm with 19 parts on 29 nets, routed with 2 tracks and 0 vias.
It is built around the ATTINY1616-MN and 1N4148WS. Its parts include 5 connectors, 4 resistors, 3 switches, 2 capacitors and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATTINY1616-MN
QFN-20-EP(3x3)-40℃~+105℃ 1.8V~5.5V 10bit 16KB 18 20MHz 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH QFN-20-EP(3x3) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching Diodes
Parts
19| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | custom_kicad_lib_sk:R_0603_smalltext | R1, R2 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 1N4148WS | Diode_SMD:D_SOD-323 | D1 |
| 1 | 1k | custom_kicad_lib_sk:R_0603_smalltext | R3 |
| 1 | 6k8 | custom_kicad_lib_sk:R_0603_smalltext | R4 |
| 1 | ATtiny1616-M | custom_kicad_lib_sk:VQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mm | U1 |
| 1 | C_Polarized | Capacitor_SMD:CP_Elec_8x10 | C2 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Horizontal | J1 |
| 1 | Conn_01x05_Socket | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Horizontal | J5 |
| 1 | G6K-2F-Y-TR DC5 | Relay_SMD:Relay_DPDT_Omron_G6K-2F-Y | K1 |
| 1 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | NPN_TOR | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J3 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3-5.08_1x03_P5.08mm_Horizontal | J4 |
| 1 | down | custom_kicad_lib_sk:tactile_SMD_6mm | SW102 |
| 1 | up | custom_kicad_lib_sk:tactile_SMD_6mm | SW101 |
The 18 most common of 19 parts.
More from bask185/Train-Science-DIY
12- 2 layers75 × 106.5 mm

- 2 layers68.5 × 130.5 mm

- 2 layers153.2 × 127.5 mm

- 2 layers54.5 × 73 mm

- 2 layers99.5 × 61 mm

- 4 layers70 × 83.5 mm

- 2 layers105.5 × 63.5 mm

- 2 layers78 × 58.5 mm

- 2 layers83.5 × 50.3 mm

- 2 layers81 × 71.2 mm

- 2 layers54 × 94.5 mm

- 2 layers100 × 45 mm

Similar boards
- 4 layers62.1 × 83.8 mm

Ss main board
loopj/short-stack
World's Smallest Nintendo Wii, using a trimmed motherboard and custom stacked PCBs
69 parts804 - 2 layers80 × 50 mm

- 4 layers100 × 68 mm

- 2 layers56.9 × 23.6 mm

Hexagon
kieraneglin/hexagon-art
A passive breakout board: two lever-terminal inputs, three JST XH outputs, all six conductors (RX bus, two spares, +12V, GND, +5V) paralleled straight across. No active components, no regulation, nothing to configure.
24 parts19 - 4 layers44.5 × 44.5 mm

Flashlight
engineerbo/flashlight-dev-hw
This repository contains design files for the development board for a flashlight boost driver. The test firmware can be found in the firmware repository.
73 parts15MIT - 2 layers29 × 36 mm

Flux Capacitor Micro Pin Badge
hojadurdy/Flux_Capacitor_Micro
A tiny (36mm x 29mm) pin badge and keychain PCB version of Flux Capacitor featuring 25 animated LEDs that animate to create the “fluxxing” effect.
48 parts6 - 4 layers50.3 × 21.5 mm

- 2 layers25.4 × 52 mm

Questions
How big is the SingleServoDriver PCB?
It measures 43 × 35 mm and has 2 copper layers, 1.6 mm thick.
What parts does the SingleServoDriver use?
19 parts, built around the ATTINY1616-MN and 1N4148WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SingleServoDriver KiCad files?
From the bask185/Train-Science-DIY repository on GitHub, at the commit this page was made from: the board is PCB_SOURCE/blockModules/SingleServoDriver/SingleServoDriver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the SingleServoDriver design in my own project?
Its repository states no licence, so its author keeps all rights: ask bask185 before reusing the design.