

Code for my 6502 build
- Size
- 102.5 × 44.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 20
- Nets
- 71
- Pads
- 176
- Tracks, vias
- 278, 134
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 24 Nov 2019
- Updated
- 19 Jul 2026
Overview
Spi is an open-source printed circuit board by atarola, from the atarola/compy6502 repository on GitHub. It is a 2-layer board of 102.5 × 44.8 mm with 20 parts on 71 nets, routed with 278 tracks and 134 vias.
It is built around the TSR 1-2433E, SN74LVC8T245PWRE4 and FM25V05-G. Its parts include 8 capacitors, 5 ICs, 5 connectors and 2 resistors. It belongs with the retro computing and games boards of this library.
Main components
3TSR 1-2433E
SIP,11.6x7.5mm-40℃~+85℃ 1 1000uF 1A 3.3V 520kHz 6V~36V 80mVp-p 88% Plastic encapsulated type Short Circuit Protection、Over-temperature protection、Over Current Protection、Automatic fault recovery Step-down type ±4% SIP,11.6x7.5mm DC-DC Power Modules ROHSTRACO POWERDC-DC Power ModulesSN74LVC8T245PWRE4
TSSOP-24-40℃~+85℃ 1 8 Level translator Power-off protection、Output enable high-impedance Tri-State TSSOP-24 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersFM25V05-G
SOIC-8-40℃~+85℃ 1.5mA 2V~3.6V 40MHz 512Kbit 5uA 90uA SPI SOIC-8 FRAM ROHSInfineon TechnologiesFRAM
README
README.mdcompy6502
compy6502 is an early-stage 6502 homebrew computer project. The long-term
goal is to build enough hardware and firmware to run Tetris on the machine.
The design follows the spirit of Ben Eater-style breadboard/modular 6502
systems for simplicity and debuggability, but uses a different memory map based
on the MMU/address-decoder architecture in docs/mmu.png.
The repo currently includes KiCad hardware designs, early ROM bring-up
firmware, build/write scripts, emulator test scaffolding, and architecture
reference images in docs/.
Memory Map
The intended memory map is:
$0000-$BFFF RAM
$C000-$C0FF I/O page
$C100-$FFFF ROMThe I/O page is split into four 64-byte device slots:
$C000-$C03F IO0B
$C040-$C07F IO1B
$C080-$C0BF IO2B
$C0C0-$C0FF IO3BThe linker script currently uses $8000-$FFFF as the 32 KB EEPROM image range
so CPU addresses map directly to the correct physical offsets on the chip.
ROM Layout
The intended ROM organization is:
$C100-$C1FF public jump table
$C200-$DFFF kernel routines and drivers
$E000-$EFFF enhanced monitor
$F500-$FFF9 Wozmon fallback monitor
$FFFA-$FFFF CPU vectorsCredits
docs/mmu.png: Mike McLaren, K8LH.docs/Beater 02b.png: Mike McLaren, K8LH.
Parts
20| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100n | Capacitor_SMD:C_0603_1608Metric | C3, C4, C5, C6, C7, C8 |
| 2 | 10u | Capacitor_SMD:C_1206_3216Metric | C1, C2 |
| 2 | 33 | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | SN74LVC8T245PWR | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U3, U4 |
| 1 | Board Connector | Connector_PinHeader_2.54mm:PinHeader_1x40_P2.54mm_Horizontal | J1 |
| 1 | FM25V05-G | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | IO Select | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J3 |
| 1 | SPI 1 | Connector_JST:JST_XH_B6B-XH-AM_1x06_P2.50mm_Vertical | J6 |
| 1 | SPI 2 | Connector_JST:JST_XH_B6B-XH-AM_1x06_P2.50mm_Vertical | J7 |
| 1 | SPI 3 | Connector_JST:JST_XH_B6B-XH-AM_1x06_P2.50mm_Vertical | J8 |
| 1 | TSR1-2433E | Converter_DCDC:Converter_DCDC_TRACO_TSR1-xxxxE_THT | U2 |
| 1 | TinyFPGA w/SPI Module | Package_DIP:DIP-28_W15.24mm_Socket_LongPads | U1 |
More from atarola/compy6502
9- 2 layers190.5 × 105 mm

- 2 layers102.5 × 30 mm

- 2 layers105.4 × 30 mm

- 2 layers102.5 × 30 mm

- 2 layers102.5 × 30 mm

- 2 layers102.5 × 30 mm

- 2 layers49.5 × 30 mm

- 2 layers102.5 × 30 mm

- 2 layers102.5 × 30 mm

Similar boards
- 2 layers160.5 × 146.5 mm

Schemav2
rayanyahiaoui13/24PowerLEDsController
The goal of this system is to provide independent and precise control of a 24-LED matrix composed of high-power LEDs to independently illuminate 24 wells of a Greiner plate containing duckweed.
146 parts1GPL-3.0 - 2 layers59 × 74.8 mm

N2k meteo gps s3 tht
titio72/n2k_router_arduino
Integrated GPS, meteo, tachometer, and speed sensor for NMEA2000 networks
45 parts1GPL-3.0 - 4 layers72.5 × 39.7 mm

FOC RP2350
totaldesaster/SimpleFOC-Serial-Driver
Advanced dual BLDC driver based on the RP2350 and DRV8323S ICs, designed to be controlled from a trajectory controller over RS-485, RS-422 or TTL UART. Features a compact high power design with two stacked PCBs.
68 parts1GPL-3.0 - 4 layers99 × 146 mm

Carte principale
Unimakers/CDR-2027
Ce repo est un site de documentation réalisé par l'équipe des première et deusième années pré-ingénieur de l'école Unilasalle-Amiens, membre de l'association de robotique Unimaker, dans le cadre de leur participation à…
156 parts1 - 2 layers80.2 × 94.6 mm

MANUEL ARGIBAYMOLINA ELECTRONICS
ManuelArgibay/Industrial-I-O-Controller
Industrial 24V I/O controller featuring protected high-side and low-side outputs, multiplexed analog and digital inputs, and MCU-based control.
89 parts - 4 layers70.5 × 109.9 mm

- 2 layers89.5 × 49 mm

Circuit Board V2
Pierowheelz/ac-vent-controller
ESP32-based controller for Aircon Vents with stepper motors.
15 parts - 2 layers57.8 × 46 mm

Modul DPS
Poky88/HAPCAN_Modul_RFID_CTECKA
This repository contains complete hardware and software resources for the development and implementation of a new extension module for the HAPCAN home automation system.
52 parts
Questions
How big is the Spi PCB?
It measures 102.5 × 44.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Spi use?
20 parts, built around the TSR 1-2433E, SN74LVC8T245PWRE4 and FM25V05-G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Spi KiCad files?
From the atarola/compy6502 repository on GitHub, at the commit this page was made from: the board is kicad/spi/spi.kicad_pcb and its schematic kicad/ACIA/ACIA.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Spi design in my own project?
Its repository states no licence, so its author keeps all rights: ask atarola before reusing the design.