Skip to the content
2 layers29 × 110.6 mmSoilSensor spi, the printed circuit board in 3D

SoilSensor spi

angelnu/esphome24

Settings for esphome

Size
29 × 110.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
23
Nets
20
Pads
91
Tracks, vias
199, 16
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
24 Dec 2019
Updated
29 Oct 2026

Overview

SoilSensor spi is an open-source printed circuit board by angelnu, from the angelnu/esphome repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 29 × 110.6 mm with 23 parts on 20 nets, routed with 199 tracks and 16 vias.

It is built around the RJ45. Its parts include 8 capacitors, 4 resistors, 2 ICs, 2 connectors and 1 diode. It belongs with the home automation and IoT boards and the STM32 boards of this library.

Main components

1

README

README.md

esphome

This repository contains my devices based on ESPHome. Each yaml in this repository represents one of my devices and can be programed following the instructions bellow.

The devices folder contains the instructions for each device (firmware, schematics, 3D boxes, etc).

Programming

To program/update these devices you need to:

  1. create a secrets.yaml file. You can use secrets_template.yaml as base
  2. start the esphome dashboard with this git repository as config folder.
  3. Connect to the dashboard
  4. First time you program your device you will need to program via a serial port. You might use a CP2104

Parts

23
QtyValueFootprintReferences
4100 nFCapacitor_SMD:C_0805_2012MetricC4, C5, C6, C7
312KResistor_SMD:R_0805_2012MetricR1, R3, R7
21 uFCapacitor_SMD:C_0805_2012MetricC8, C10
210 pFCapacitor_SMD:C_0805_2012MetricC1, C2
2MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2
12M2Resistor_SMD:R_0805_2012MetricR2
132KHzCrystal:Crystal_SMD_3215-2Pin_3.2x1.5mmY1
1BOOTButton_Switch_SMD:SW_SPST_TL3342BOOT1
1Conn_01x06_MaleConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ1
1Ferrite_Bead_SmallResistor_SMD:R_0805_2012MetricFB1
1LEDDiode_SMD:D_0805_2012MetricD1
1RESETButton_Switch_SMD:SW_SPST_TL3342RESET1
1RJ45Connector_RJ:RJ45_kycon_GMX-SMT2-S-88-TR_HorizontalJ2
1STM32L041K6TxPackage_QFP:LQFP-32_7x7mm_P0.8mmU1
1SoilSondeSonde:soilSondeU3

More from angelnu/esphome

4
  • 2 layers43.5 × 37 mmSiedle bus, the printed circuit board in 3D

    Siedle bus

    angelnu/esphome

    Settings for esphome

    37 parts24Apache-2.0
  • 2 layers57.1 × 56.3 mmEsp32-temp, the printed circuit board in 3D

    Esp32-temp

    angelnu/esphome

    Settings for esphome

    28 parts24Apache-2.0
  • 2 layers61 × 28 mmPcb led lights, the printed circuit board in 3D

    Pcb led lights

    angelnu/esphome

    Settings for esphome

    25 parts24Apache-2.0

Similar boards

  • 2 layers33.7 × 97.8 mmHAN ESP TSS721, the printed circuit board in 3D

    HAN ESP TSS721

    UtilitechAS/amsreader-firmware

    ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported

    29 parts470
  • 4 layers84 × 82 mmToad, the printed circuit board in 3D

    Toad

    travisgoodspeed/goodfet

    An embedded bus adapter for various microcontrollers and radios.

    241 parts333
  • 2 layers100 × 100 mmCANBuster, the printed circuit board in 3D

    CANBuster

    GBert/misc

    miscellaneous stuff / unsorted

    182 parts99
  • 2 layers50 × 55.4 mmCasserole, the printed circuit board in 3D

    Casserole

    puddly/casserole

    Control GE appliances

    23 parts94Apache-2.0
  • 2 layers67.9 × 47.8 mmPlatine, the printed circuit board in 3D

    Platine

    nv1t/standing-desk-interceptor

    I wanted to intercept the communication between my Flexispot standing desk buttons. This is the progress on the project

    11 parts52CC0-1.0
  • 4 layers90 × 75 mmCM4 2 Backup, the printed circuit board in 3D

    CM4 2 Backup

    olvint/CM4-NAS-MiniPCIE

    Raspberry Pi CM4 based NAS solution board

    21 parts51
  • 4 layers73.9 × 84.5 mmAei, the printed circuit board in 3D

    Aei

    Severson-Group/AMDC-Hardware

    Circuit board designs for controlling advanced motor systems

    54 parts51
  • 2 layers99 × 60 mmPwr, the printed circuit board in 3D

    Pwr

    mfkiwl/KiwiSDR_PCB

    KiCAD PCB files for KiwiSDR project including active antenna and bias tee

    64 parts46

Questions

How big is the SoilSensor spi PCB?

It measures 29 × 110.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the SoilSensor spi use?

23 parts, built around the RJ45. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the SoilSensor spi KiCad files?

From the angelnu/esphome repository on GitHub, at the commit this page was made from: the board is devices/pcb-pot-watering/sensor/KiCad/SoilSensor_spi.kicad_pcb and its schematic devices/pcb-led_lights/kicad/pcb-led-lights/pcb-led-lights.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the SoilSensor spi design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).