
Cuttlefish
AllenNeuralDynamics/harp.device.cuttlefish
0414: an octal, TTL input/output device with programmable square wave output.

My ears and speakers will last a lifetime (I hope), but home theatre audio standards do not. My old stereo amplifier works fine, why can't I get an HDMI upgrade module that gives it CEC (control via TV remote).
Flexible audio hub is an open-source printed circuit board by andrew-bolin, from the andrew-bolin/flexible_audio_hub repository on GitHub. It is a 4-layer board of 100 × 100 mm with 91 parts on 118 nets, routed with 884 tracks and 201 vias.
It is built around the 74CBTLV3245PW, AT24CS32-SSHM-T and 74AHC595D, with the L7805, LM1117-3.3 and TCA9546AD among its other parts. Its parts include 55 resistors, 16 capacitors, 12 ICs, 7 connectors and 1 diode. It belongs with the audio and music boards of this library.
My ears and speakers will last a lifetime (I hope), but home theatre audio standards do not. My old stereo amplifier works fine, why can't I get an HDMI upgrade module that gives it CEC (control via TV remote). If I buy a 5.1 channel amplifier, why do I have to throw it in the bin to upgrade to Atmos?
A modern AVR (Audio-Video Receiver) is a fantastic piece of technology, but they are available only in certain fixed configurations and are not easily modifiable.
The modular system will be entirely open-source so that any interested person can make their own module to serve their unique needs (or for fun). Eventually I would like to see compatible modules available from multiple vendors (much like Raspberry Pi & Arduino add-ons).
The Current Specification - very much a work in progress!
The first stage will be electrical & communications protocol only.
Currently, I am deciding on a connector - if anyone knows a connector that is a reasonable pitch (0.5 - 2.5mm), keyed, upwards-compatible with extra pins (e.g. a 16-pin plug can fit into a 20-pin socket), and cheap, please get in contact!
Previously, I started a similar project using a backplane, because edge connectors are cheap, but the design I was using had the switching complexity by necessity in every module, was difficult to integrate into a chassis, and did not offer full flexibility for multiple simultaneous outputs. Now I will move that complexity to a "hub" board.
Each module should (yes, it's optional) have an ID EEPROM & accept a few basic commands (Enable, select channel) via I2C. This can be achieved via a PCA9500 I/O expander or ATtiny, for example. Modules without the ID/Control interface will require more configuration effort and might waste a bit more power (the central hub will probably not have power switches per module).
The hub will be controlled by I2C, and a C++ library will be provided that will be usable via Arduino and Raspberry Pi. The hub will be able to be daisy-chained.
These files are distributed under The TAPR Open Hardware License, version 1.0.
See LICENSE.txt or https://www.tapr.org/ohl.html
| Qty | Value | Footprint | References |
|---|---|---|---|
| 53 | R_Small | Resistors_SMD:R_0805_HandSoldering | R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25, R26 +37 |
| 14 | C_Small | Capacitors_SMD:C_0805_HandSoldering | C1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11, C14, C15, C16 |
| 6 | 74CBTLV3245 | Housings_SSOP:TSSOP-20_4.4x6.5mm_Pitch0.65mm | U4, U5, U6, U7, U10, U11 |
| 4 | Conn_02x08_Odd_Even | Pin_Headers:Pin_Header_Straight_2x08_Pitch2.54mm | J2, J4, J5, J6 |
| 2 | 10uF | Capacitors_THT:CP_Radial_D5.0mm_P2.00mm | C12, C13 |
| 2 | 3k9 | Resistors_SMD:R_0805_HandSoldering | R1, R2 |
| 2 | AT24CS32-SSHM | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U1, U12 |
| 1 | 74AHC595 | Housings_SOIC:SOIC-16_3.9x9.9mm_Pitch1.27mm | U2 |
| 1 | Barrel_Jack | Connectors:BARREL_JACK | J7 |
| 1 | Conn_01x08 | Pin_Headers:Pin_Header_Straight_1x08_Pitch2.54mm | J3 |
| 1 | Conn_02x20_Odd_Even | Pin_Headers:Pin_Header_Straight_2x20_Pitch2.54mm | J1 |
| 1 | D | Diodes_THT:D_5W_P10.16mm_Horizontal | D1 |
| 1 | L7805 | TO_SOT_Packages_THT:TO-220_Vertical | U8 |
| 1 | LM1117-3.3 | TO_SOT_Packages_THT:TO-220_Vertical | U9 |
| 1 | TCA9546A | Housings_SSOP:TSSOP-16_4.4x5mm_Pitch0.65mm | U3 |

AllenNeuralDynamics/harp.device.cuttlefish
0414: an octal, TTL input/output device with programmable square wave output.

alvarop/ostur
This is a work in progress for a cheese cave controller system. The goal is to be able to control a mini fridge to get the right conditions for cheesemaking.

2468shrm/Pico-Robotic-Controller
A carrier board for a Raspberry Pi Pico (W) for use in FRC robotics. Similar to the XRP board.

BarbourSmith/Maslow-Mini-Control-Board
A third KiCad project that puts both existing boards on one PCB:




It measures 100 × 100 mm and has 4 copper layers, 1.6 mm thick.
91 parts, built around the 74CBTLV3245PW, AT24CS32-SSHM-T, 74AHC595D and L7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the andrew-bolin/flexible_audio_hub repository on GitHub, at the commit this page was made from: the board is flexibleaudiohub.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask andrew-bolin before reusing the design.