Skip to the content
12345678910111213141516

TCA9546AD

Texas InstrumentsExtended

-40℃~+85℃ 1.65V~5.5V 1.6uA 1ns 7mA Bus Switch Level shifting、Hot-swap protection Single Supply SOIC-16 Signal Switches, Multiplexers, Decoders ROHS

Part id
ti/TCA9546AD
Category
Signal Switches, Multiplexers, Decoders
Package
SOIC-16
Pins
16
In stock
3,422 at JLCPCB (C2653349)
Used on
7 open-source boards

Overview

The TCA9546AD is a signal Switches, Multiplexers, Decoder made by Texas Instruments in a SOIC-16 package with 16 pins. -40℃~+85℃ 1.65V~5.5V 1.6uA 1ns 7mA Bus Switch Level shifting、Hot-swap protection Single Supply SOIC-16 Signal Switches, Multiplexers, Decoders ROHS.

PCBKit's library has its KiCad symbol (Interface_Expansion:TCA9546AD, from KiCad's library) and its footprint (Package_SO:SOIC-16_3.9x9.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 3,422 are in stock at JLCPCB (part C2653349). 7 open-source boards in 6 repositories on GitHub use it.

Symbol

1A02A13RESET4SD05SC06SD17SC18GND9SD210SC211SD312SC313A214SCL15SDA16VCC
Interface_Expansion:TCA9546ADFrom KiCad's library

Footprint

12345678910111213141516
Package_SO:SOIC-16_3.9x9.9mm_P1.27mmFrom KiCad's library

From the datasheet

12
Supply, least
1.65 V · VCC, recommended operating min · p. 4
Supply, most
5.5 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
7 V · VCC, absolute max · p. 4
Works from
-40 °C · Operating free-air temperature min · p. 4
Works up to
85 °C · Operating free-air temperature max · p. 4
Takes working
50 µA · VCC operating typical, 5.5 V, fSCL = 400 kHz, IO = 0 · p. 5
Takes asleep
1.6 µA · VCC standby typical, 5.5 V, low inputs, IO = 0 · p. 5
A pin gives at most
25 mA · Output current absolute max magnitude · p. 4
Junction to air (D)
92.3 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (D)
52.3 K/W · Junction-to-case (top) thermal resistance · p. 4
Junction to board (D)
50.1 K/W · Junction-to-board thermal resistance · p. 4
Data rate, most
400 kbit/s · Fast mode I2C clock frequency max · p. 6

What it is and has

7
Switch channels
4, bidirectional translating I2C · p. 10
Bus compatibility
I2C and SMBus · p. 1
Reset
Active-low reset input · p. 1
Channel selection
Any combination via I2C bus · p. 1
Power-up state
All switch channels deselected · p. 1
Hot insertion
Supported · p. 1
Input tolerance
5.5 V · p. 1

Around it

11
res not specified
between RESET and VCC or VDPUM; Pull-up resistor if reset input is not used. · p. 3
res not specified
between SD0 and VDPU0; Pull-up resistor. · p. 3
res not specified
between SC0 and VDPU0; Pull-up resistor. · p. 3
res not specified
between SD1 and VDPU1; Pull-up resistor. · p. 3
res not specified
between SC1 and VDPU1; Pull-up resistor. · p. 3
res not specified
between SD2 and VDPU2; Pull-up resistor. · p. 3
res not specified
between SC2 and VDPU2; Pull-up resistor. · p. 3
res not specified
between SD3 and VDPU3; Pull-up resistor. · p. 3
res not specified
between SC3 and VDPU3; Pull-up resistor. · p. 3
res not specified
between SCL and VDPUM; Pull-up resistor. · p. 3
res not specified
between SDA and VDPUM; Pull-up resistor. · p. 3

Specifications

102
ParameterConditionsAs printedPage
Supply voltage range VCCmin -0.5 · max 7 V4
Input voltage range VImin -0.5 · max 7 V4
Input current IIRating is ±20 mAmax 20 mA4
Output current IORating is ±25 mAmax 25 mA4
Continuous current through VCCRating is ±100 mAmax 100 mA4
Continuous current through GNDRating is ±100 mAmax 100 mA4
Total power dissipation Ptotmax 400 mW4
Operating free-air temperature range TAmin -40 · max 85 °C4
Storage temperature range Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±4000 Vmax 4000 V4
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1500 Vmax 1500 V4
Supply voltage VCCmin 1.65 · max 5.5 V4
High-level input voltage VIHSCL, SDAmax 6 V4
Low-level input voltage VILSCL, SDAmin -0.5 V4
Low-level input voltage VILA2–A0, RESETmin -0.5 V4
Operating free-air temperature TAmin -40 · max 85 °C4
Junction-to-ambient thermal resistance RθJAD, 16 pinstyp 92.3 °C/W4
Junction-to-case (top) thermal resistance RθJCtopD, 16 pinstyp 52.3 °C/W4
Junction-to-board thermal resistance RθJBD, 16 pinstyp 50.1 °C/W4
Junction-to-top characterization parameter ψJTD, 16 pinstyp 17.7 °C/W4
Junction-to-board characterization parameter ψJBD, 16 pinstyp 49.8 °C/W4
Power-on reset voltage, VCC rising VPORRNo load, VI = VCC or GNDtyp 1.2 · max 1.5 V5
Power-on reset voltage, VCC falling VPORFNo load, VI = VCC or GNDmin 0.8 · typ 1 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 5 Vtyp 3.6 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 4.5 V to 5.5 Vmin 2.6 · max 4.5 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 3.3 Vtyp 1.9 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 3 V to 3.6 Vmin 1.6 · max 2.8 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 2.5 Vtyp 1.4 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 2.3 V to 2.7 Vmin 1 · max 1.8 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 1.8 Vtyp 0.8 V5
Switch output voltage VpassVSWin = VCC, ISWout = –100 uA, VCC = 1.65 V to 1.95 Vmin 0.5 · max 1.1 V5
SDA IOLVOL = 0.4 V, VCC = 1.65 V to 5.5 Vmin 3 · typ 7 mA5
SDA IOLVOL = 0.6 V, VCC = 1.65 V to 5.5 Vmin 6 · typ 10 mA5
SCL, SDA IIVI = VCC or GND, VCC = 1.65 V to 5.5 V; ±1 uAmax 1 uA5
SC3–SC0, SD3–SD0 IIVI = VCC or GND, VCC = 1.65 V to 5.5 V; ±1 uAmax 1 uA5
A2–A0 IIVI = VCC or GND, VCC = 1.65 V to 5.5 V; ±1 uAmax 1 uA5
RESET IIVI = VCC or GND, VCC = 1.65 V to 5.5 V; ±1 uAmax 1 uA5
Operating mode ICCfSCL = 400 kHz, VI = VCC or GND, IO = 0, tr,max = 300 ns, VCC = 5.5 Vtyp 50 uA5
Operating mode ICCfSCL = 400 kHz, VI = VCC or GND, IO = 0, tr,max = 300 ns, VCC = 3.6 Vtyp 20 uA5
Operating mode ICCfSCL = 400 kHz, VI = VCC or GND, IO = 0, tr,max = 300 ns, VCC = 2.7 Vtyp 11 uA5
Operating mode ICCfSCL = 400 kHz, VI = VCC or GND, IO = 0, tr,max = 300 ns, VCC = 1.65 Vtyp 6 uA5
Operating mode ICCfSCL = 100 kHz, VI = VCC or GND, IO = 0, tr,max = 1 us, VCC = 5.5 Vtyp 35 uA5
Operating mode ICCfSCL = 100 kHz, VI = VCC or GND, IO = 0, tr,max = 1 us, VCC = 3.6 Vtyp 14 uA5
Operating mode ICCfSCL = 100 kHz, VI = VCC or GND, IO = 0, tr,max = 1 us, VCC = 2.7 Vtyp 5 uA5
Operating mode ICCfSCL = 100 kHz, VI = VCC or GND, IO = 0, tr,max = 1 us, VCC = 1.65 Vtyp 2 uA5
Standby mode ICCLow inputs, VI = GND, IO = 0, VCC = 5.5 Vtyp 1.6 · max 2 uA5
Standby mode ICCLow inputs, VI = GND, IO = 0, VCC = 3.6 Vtyp 1 · max 1.3 uA5
Standby mode ICCLow inputs, VI = GND, IO = 0, VCC = 2.7 Vtyp 0.7 · max 1.1 uA5
Standby mode ICCLow inputs, VI = GND, IO = 0, VCC = 1.65 Vtyp 0.4 · max 0.55 uA5
Standby mode ICCHigh inputs, VI = VCC, IO = 0, VCC = 5.5 Vtyp 1.6 · max 2 uA5
Standby mode ICCHigh inputs, VI = VCC, IO = 0, VCC = 3.6 Vtyp 1 · max 1.3 uA5
Standby mode ICCHigh inputs, VI = VCC, IO = 0, VCC = 2.7 Vtyp 0.7 · max 1.1 uA5
Standby mode ICCHigh inputs, VI = VCC, IO = 0, VCC = 1.65 Vtyp 0.4 · max 0.55 uA5
Supply-current change ΔICCSCL, SDA; SCL or SDA input at 0.6 V, other inputs at VCC or GND, VCC = 1.65 V to 5.5 Vtyp 2 · max 15 uA5
Supply-current change ΔICCSCL, SDA; SCL or SDA input at VCC – 0.6 V, other inputs at VCC or GND, VCC = 1.65 V to 5.5 Vtyp 2 · max 15 uA5
A2–A0 CiVI = VCC or GND, VCC = 1.65 V to 5.5 Vtyp 4.5 · max 6 pF5
RESET CiVI = VCC or GND, VCC = 1.65 V to 5.5 Vtyp 4.5 · max 5.5 pF5
SCL, SDA Cio(OFF)VI = VCC or GND, switch OFF, VCC = 1.65 V to 5.5 Vtyp 15 · max 19 pF5
SC3–SC0, SD3–SD0 Cio(OFF)VI = VCC or GND, switch OFF, VCC = 1.65 V to 5.5 Vtyp 6 · max 8 pF5
Switch on-state resistance RONVO = 0.4 V, IO = 15 mA, VCC = 4.5 V to 5.5 Vmin 4 · typ 10 · max 16 Ω6
Switch on-state resistance RONVO = 0.4 V, IO = 15 mA, VCC = 3 V to 3.6 Vmin 5 · typ 13 · max 20 Ω6
Switch on-state resistance RONVO = 0.4 V, IO = 10 mA, VCC = 2.3 V to 2.7 Vmin 7 · typ 16 · max 45 Ω6
Switch on-state resistance RONVO = 0.4 V, IO = 10 mA, VCC = 1.65 V to 1.95 Vmin 10 · typ 25 · max 70 Ω6
I2C clock frequency fsclSTANDARD MODE I2C BUSmin 0 · max 100 kHz6
I2C clock frequency fsclFAST MODE I2C BUSmin 0 · max 400 kHz6
I2C clock high time tschSTANDARD MODE I2C BUSmin 4 us6
I2C clock high time tschFAST MODE I2C BUSmin 0.6 us6
I2C clock low time tsclSTANDARD MODE I2C BUSmin 4.7 us6
I2C clock low time tsclFAST MODE I2C BUSmin 1.3 us6
I2C spike time tspSTANDARD MODE I2C BUSmax 50 ns6
I2C spike time tspFAST MODE I2C BUSmax 50 ns6
I2C serial-data setup time tsdsSTANDARD MODE I2C BUSmin 250 ns6
I2C serial-data setup time tsdsFAST MODE I2C BUSmin 100 ns6
I2C serial-data hold time tsdhSTANDARD MODE I2C BUSmin 0 us6
I2C serial-data hold time tsdhFAST MODE I2C BUSmin 0 us6
I2C input rise time ticrSTANDARD MODE I2C BUSmax 1000 ns6
I2C input rise time ticrFAST MODE I2C BUS; Cb is total bus capacitance of one bus line in pFmax 300 ns6
I2C input fall time ticfSTANDARD MODE I2C BUSmax 300 ns6
I2C input fall time ticfFAST MODE I2C BUS; Cb is total bus capacitance of one bus line in pFmax 300 ns6
I2C output fall time tocfSTANDARD MODE I2C BUS; 10-pF to 400-pF busmax 300 ns6
I2C output fall time tocfFAST MODE I2C BUS; 10-pF to 400-pF bus; Cb is total bus capacitance of one bus line in pFmax 300 ns6
I2C bus free time between stop and start tbufSTANDARD MODE I2C BUSmin 4.7 us6
I2C bus free time between stop and start tbufFAST MODE I2C BUSmin 1.3 us6
I2C start or repeated start condition setup tstsSTANDARD MODE I2C BUSmin 4.7 us6
I2C start or repeated start condition setup tstsFAST MODE I2C BUSmin 0.6 us6
I2C start or repeated start condition hold tsthSTANDARD MODE I2C BUSmin 4 us6
I2C start or repeated start condition hold tsthFAST MODE I2C BUSmin 0.6 us6
I2C stop condition setup tspsSTANDARD MODE I2C BUSmin 4 us6
I2C stop condition setup tspsFAST MODE I2C BUSmin 0.6 us6
Valid-data time (high to low) tvdL(Data)STANDARD MODE I2C BUS; SCL low to SDA output low validmax 1 us6
Valid-data time (high to low) tvdL(Data)FAST MODE I2C BUS; SCL low to SDA output low validmax 1 us6
Valid-data time (low to high) tvdH(Data)STANDARD MODE I2C BUS; SCL low to SDA output high validmax 0.6 us6
Valid-data time (low to high) tvdH(Data)FAST MODE I2C BUS; SCL low to SDA output high validmax 0.6 us6
Valid-data time of ACK condition tvd(ack)STANDARD MODE I2C BUS; ACK signal from SCL low to SDA output lowmax 1 us6
Valid-data time of ACK condition tvd(ack)FAST MODE I2C BUS; ACK signal from SCL low to SDA output lowmax 1 us6
I2C bus capacitive load CbSTANDARD MODE I2C BUSmax 400 pF6
I2C bus capacitive load CbFAST MODE I2C BUSmax 400 pF6
Propagation delay time tpdRON = 20 Ω, CL = 15 pF; SDA or SCL to SDn or SCnmax 0.3 ns6
Propagation delay time tpdRON = 20 Ω, CL = 50 pF; SDA or SCL to SDn or SCnmax 1 ns6
Pulse duration, RESET low tWLmin 6 ns7
RESET time (SDA clear) trstmax 500 ns7
Recovery time from RESET to start tREC(STA)min 0 ns7

Pins, by the datasheet

16
1 A0
Address input 0. Connect directly to VCC or ground. · p. 3
2 A1
Address input 1. Connect directly to VCC or ground. · p. 3
3 RESET
Active low reset input. Connect to VCC or VDPUM through a pull-up resistor if not used. · p. 3
4 SD0
Serial data 0. Connect to VDPU0 through a pull-up resistor. · p. 3
5 SC0
Serial clock 0. Connect to VDPU0 through a pull-up resistor. · p. 3
6 SD1
Serial data 1. Connect to VDPU1 through a pull-up resistor. · p. 3
7 SC1
Serial clock 1. Connect to VDPU1 through a pull-up resistor. · p. 3
8 GND
Ground. · p. 3
9 SD2
Serial data 2. Connect to VDPU2 through a pull-up resistor. · p. 3
10 SC2
Serial clock 2. Connect to VDPU2 through a pull-up resistor. · p. 3
11 SD3
Serial data 3. Connect to VDPU3 through a pull-up resistor. · p. 3
12 SC3
Serial clock 3. Connect to VDPU3 through a pull-up resistor. · p. 3
13 A2
Address input 2. Connect directly to VCC or ground. · p. 3
14 SCL
Serial clock line. Connect to VDPUM through a pull-up resistor. · p. 3
15 SDA
Serial data line. Connect to VDPUM through a pull-up resistor. · p. 3
16 VCC
Supply power. · p. 3

Open-source boards using it

7
  • 2 layersController, the printed circuit board in 3D

    Controller

    alvarop/ostur

    This is a work in progress for a cheese cave controller system. The goal is to be able to control a mini fridge to get the right conditions for cheesemaking.

    89 parts8MIT
  • 4 layers100 × 100 mmFlexible audio hub, the printed circuit board in 3D

    Flexible audio hub

    andrew-bolin/flexible_audio_hub

    My ears and speakers will last a lifetime (I hope), but home theatre audio standards do not. My old stereo amplifier works fine, why can't I get an HDMI upgrade module that gives it CEC (control via TV remote).

    91 parts8
  • 4 layers91 × 110 mmPico Robotic Controller, the printed circuit board in 3D

    Pico Robotic Controller

    2468shrm/Pico-Robotic-Controller

    A carrier board for a Raspberry Pi Pico (W) for use in FRC robotics. Similar to the XRP board.

    103 parts
  • 4 layers153 × 111 mmMaslow Mini Merged Board, the printed circuit board in 3D

    Maslow Mini Merged Board

    BarbourSmith/Maslow-Mini-Control-Board

    A third KiCad project that puts both existing boards on one PCB:

    156 parts
  • 14 layers205.6 × 228.6 mmAcmi2-fpga, the printed circuit board in 3D

    Acmi2-fpga

    jamead/acmi2-hw-fpgabrd

    ACMI-2 KiCad files for the FPGA Board

    406 parts
  • 12 layers241.3 × 170.4 mmCc afe, the printed circuit board in 3D

    Cc afe

    jamead/cc-afe-hw

    Cell Controller AFE KiCad PCB

    376 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TCA9546AD?

Yes. The symbol is Interface_Expansion:TCA9546AD and the footprint Package_SO:SOIC-16_3.9x9.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TCA9546AD?

SOIC-16, with 16 pins. Its footprint is drawn on this page.

Where is the TCA9546AD datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TCA9546AD?

JLCPCB lists it as part C2653349, with 3,422 in stock; the sellers' links on this page open their listings.

What can replace the TCA9546AD?

Parts like it in the library: the 74HC4053M/TR by HGSEMI, the SN74HC138D by Texas Instruments, the 74HC138D by JSMSEMI and the MC74HC138AD by onsemi. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TCA9546AD?

7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.