

Flight ControllerV1.0
Drone and Rocket Development PCB board
- Size
- 62.2 × 54.6 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 59
- Nets
- 79
- Pads
- 275
- Tracks, vias
- 419, 62
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 16 Feb 2023
- Updated
- 16 Feb 2023
Overview
Flight ControllerV1.0 is an open-source printed circuit board by alihaanc, from the alihaanc/SKYKILLER-Development-Board repository on GitHub. It is a 4-layer board of 62.2 × 54.6 mm with 59 parts on 79 nets, routed with 419 tracks and 62 vias.
It is built around the BMP280, AMS1117-3.3 and MPU-6050, with the USBLC6-2SC6 and AO3401A among its other parts. Its parts include 21 capacitors, 10 connectors, 8 resistors, 5 ICs and 3 diodes. It belongs with the STM32 boards of this library.
Main components
5BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometersUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)AO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
README
README.mdSKYKILLER-Development-Board
Drone and Rocket Development PCB board
Different Color
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C12, C14, C15, C17, C18, C19, C21, C22 |
| 4 | 4k7 | Resistor_SMD:R_0603_1608Metric | R5, R6, R7, R9 |
| 4 | MOTOR | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5, J6, J8, J9 |
| 3 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C2, C7, C8 |
| 3 | MountingHole_Pad | MountingHole:MountingHole_4.3mm_M4_Pad_Via | H1, H2, H3 |
| 2 | 100ohm @100MHz | Inductor_SMD:L_0805_2012Metric | FB1, FB2 |
| 2 | 12pF | Capacitor_SMD:C_0402_1005Metric | C13, C16 |
| 2 | 1k5 | Resistor_SMD:R_0201_0603Metric | R2, R3 |
| 2 | LOGO | LOGO | G***, G*** |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C20 |
| 1 | 10uF | Capacitor_SMD:CP_Elec_4x5.4 | C4 |
| 1 | 1k5 | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 1uF | Capacitor_SMD:CP_Elec_4x5.4 | C3 |
| 1 | 22uF | Capacitor_SMD:CP_Elec_4x5.4 | C6 |
| 1 | 2A | Fuse:Fuse_0603_1608Metric | F1 |
| 1 | 2n2 | Capacitor_SMD:C_0603_1608Metric | C23 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C11 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U6 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | BLUE | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | D_Schottky | Diode_SMD:D_SOD-123F | D1 |
| 1 | GPIO | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Horizontal | J2 |
| 1 | HSE 16 MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y2 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U4 |
| 1 | MountingHole_GND | MountingHole:MountingHole_4.3mm_M4_Pad_Via | H4 |
| 1 | RED | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | SERVO 1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | SERVO 2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10 |
| 1 | STM32F411CEUx | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U1 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW1 |
| 1 | USART | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | J1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_B_Mini | Connector_USB:USB_Mini-B_Wuerth_65100516121_Horizontal | J3 |
Similar boards
- 2 layers48.1 × 48 mm

- 2 layers51.7 × 43.6 mm

STM32F103C8T6 2 layer design (with optimization)
Ferid10/STM32F103C8T6-design
my pcb design where i made a stm 32 board with temprature and pressure sensor using both spi and i2c communication
38 parts - 4 layers81 × 53 mm

Pratham
PeriwalPratham/FlightController
A basic PCB design which contains all components for a solo yet affordable basic drone controller
102 partsMIT - 2 layers50 × 50 mm

PCB DRONE
shreejita56/XiZi-PCB-DRONE
So I made a custom PCB based on Esp32 . It holds an IMU and a Barometer for control . It has a normal 4 Motor Layout 2 motors will move clock wise and 2 will be anti-clock wise direction.
68 parts - 2 layers63 × 99 mm

BionxBatteryBoard
William-Yen/Bionx-3rdParty-BMS
A supplemental PCB to retrofit a Bionx e-bike battery pack with a 3rd-party BMS
144 partsGPL-3.0 - 2 layers96.6 × 100 mm

- 2 layers38 × 38 mm

MetalBird v2.kicad pro
Rajveer1496/MetalBird
A Drone made entirely from scratch. From PCB design and body to own Firmware.
67 parts2 - 2 layers45 × 45 mm

AVR FLIGHT CONTROLLER
syeedameen/miniflight
Budget Flight Controller for Drones with ATmega328P Microcontroller
65 parts2GPL-3.0
Questions
How big is the Flight ControllerV1.0 PCB?
It measures 62.2 × 54.6 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Flight ControllerV1.0 use?
59 parts, built around the BMP280, AMS1117-3.3, MPU-6050 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Flight ControllerV1.0 KiCad files?
From the alihaanc/SKYKILLER-Development-Board repository on GitHub, at the commit this page was made from: the board is Flight_ControllerV1.0/Flight_ControllerV1.0.kicad_pcb and its schematic Flight_ControllerV1.0/Flight_ControllerV1.0.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Flight ControllerV1.0 design in my own project?
Its repository states no licence, so its author keeps all rights: ask alihaanc before reusing the design.