4 layers62.2 × 54.6 mm
Flight ControllerV1.0
alihaanc/SKYKILLER-Development-Board
Drone and Rocket Development PCB board
59 parts2
2 layers51.7 × 43.6 mm
STM32F103C8T6 2 layer design (with optimization)
Ferid10/STM32F103C8T6-designmy pcb design where i made a stm 32 board with temprature and pressure sensor using both spi and i2c communication
- Size
- 51.7 × 43.6 mm
- Copper layers
- 2
- Thickness
- 0.27 mm
- Parts
- 38
- Nets
- 73
- Pads
- 209
- Tracks, vias
- 381, 29
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 11 Apr 2025
- Updated
- 11 Apr 2025
Overview
STM32F103C8T6 2 layer design (with optimization) is an open-source printed circuit board by Ferid10, from the Ferid10/STM32F103C8T6-design repository on GitHub. It is a 2-layer board of 51.7 × 43.6 mm with 38 parts on 73 nets, routed with 381 tracks and 29 vias.
It is built around the STM32F103C8T6, BMP280 and AMS1117-3.3, with the MPU-6050 and USBLC6-2SC6 among its other parts. Its parts include 22 capacitors, 5 ICs, 4 resistors, 2 connectors and 2 switches. It belongs with the STM32 boards of this library.
Main components
5
STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure Sensors
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
Parts
38| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nf | Capacitor_SMD:C_01005_0402Metric | C1, C2, C3, C5, C6, C11, C12, C13, C14, C15, C16 |
| 4 | 18pf | Capacitor_SMD:C_01005_0402Metric | C7, C8, C9, C10 |
| 3 | 1.1k | Resistor_SMD:R_0402_1005Metric | R1, R2, R4 |
| 2 | 100nf | Capacitor_SMD:C_0402_1005Metric | C18, C20 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C21, C22 |
| 2 | 1uf | Capacitor_SMD:C_0201_0603Metric | C4, C17 |
| 2 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1, Y2 |
| 1 | 10nf | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 1k5 | Resistor_SMD:R_01005_0402Metric | R3 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U5 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U3 |
| 1 | RED | LED_SMD:LED_2512_6332Metric | D1 |
| 1 | STM32F103C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | SW_MEC_5G | Button_Switch_SMD:SW_MEC_5GSH9 | SW1 |
| 1 | SW_Push_SPDT | Button_Switch_SMD:SW_DIP_SPSTx01_Slide_Copal_CVS-01xB_W5.9mm_P1mm | SW2 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_B_Micro | Connector_USB:USB_Mini-B_Lumberg_2486_01_Horizontal | J1 |
Similar boards
- 4 layers81 × 53 mm
Pratham
PeriwalPratham/FlightController
A basic PCB design which contains all components for a solo yet affordable basic drone controller
102 partsMIT - 2 layers50 × 63 mm
Zenith Development Board
zenitheesc/Zenith-Development-Board
The Zenith Development Board was developed to serve as a first project for the new members of the group.
69 parts3MIT - 2 layers
- 2 layers48.1 × 48 mm
- 2 layers96.6 × 100 mm
- 2 layers38 × 38 mm
MetalBird v2.kicad pro
Rajveer1496/MetalBird
A Drone made entirely from scratch. From PCB design and body to own Firmware.
67 parts2 - 2 layers45 × 45 mm
AVR FLIGHT CONTROLLER
syeedameen/miniflight
Budget Flight Controller for Drones with ATmega328P Microcontroller
65 parts2GPL-3.0
Questions
How big is the STM32F103C8T6 2 layer design (with optimization) PCB?
It measures 51.7 × 43.6 mm and has 2 copper layers, 0.27 mm thick.
What parts does the STM32F103C8T6 2 layer design (with optimization) use?
38 parts, built around the STM32F103C8T6, BMP280, AMS1117-3.3 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STM32F103C8T6 2 layer design (with optimization) KiCad files?
From the Ferid10/STM32F103C8T6-design repository on GitHub, at the commit this page was made from: the board is STM32F103C8T6 2 layer design (with optimization).kicad_pcb and its schematic STM32F103C8T6 2 layer design (with optimization).kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the STM32F103C8T6 2 layer design (with optimization) design in my own project?
Its repository states no licence, so its author keeps all rights: ask Ferid10 before reusing the design.