

- Size
- 145 × 108 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 93
- Nets
- 109
- Pads
- 511
- Tracks, vias
- 1,006, 159
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 25 Jan 2024
- Updated
- 18 Jan 2026
Overview
RC15 is an open-source printed circuit board by AgOpenGPS-Official, from the AgOpenGPS-Official/Rate_Control repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 145 × 108 mm with 93 parts on 109 nets, routed with 1,006 tracks and 159 vias.
It is built around the MAX3485EESA+T, CH340C and ESP32-WROOM-32U, with the DRV8870DDA, ADS1115IDGS and PCA9685PW among its other parts. Its parts include 33 capacitors, 20 ICs, 13 resistors, 9 connectors and 8 diodes. It belongs with the ESP32 boards of this library.
Main components
12MAX3485EESA+T
SOIC-8-40℃~+85℃ 1 1 12Mbps 2.2mA 3V~3.6V Half-Duplex Transceiver ±15kV SOIC-8 RS-485 / RS-422 ICs ROHSMaxim Integrated (Analog Devices)RS-485 / RS-422 ICsCH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersESP32-WROOM-32U
SMD,19.2x18mm-40℃~+85℃ -97dBm 2.4GHz 20.5dBm 3V~3.6V Bluetooth4.2 ESP32-DOWD UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC、CAN SMD,19.2x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesDRV8870DDA
SO-8-40℃~+125℃ 1 3.6A 565mΩ 6.5V~45V 6.5V~45V Bipolar Driver Overcurrent Protection、Short-Circuit Protection、Over temperature protection、Under-voltage lockout、Overvoltage Protection、Built-in charge pump、Power-on reset、Dead-time / shoot-through protection Yes SO-8 Stepper Motor Driver ROHSTexas InstrumentsStepper Motor DriverADS1115IDGS
MSOP10Ultra-Small, Low-Power, 4 Channels 16-Bit Analog-to-Digital Converter with Internal ReferenceTexas InstrumentsUncategorisedPCA9685PW
TSSOP-28-40℃~+85℃ 100kHz~1MHz 16 2.3V~5.5V 25mA 5.5V Built-in PWM TSSOP-28 LED Drivers ROHSNXP SemiconductorsLED DriversAZ1117CD
800mA LDO Voltage RegulatorDiodes IncorporatedUncategorisedPCA9306DCUR
VSSOP-8-40℃~+85℃ 1 1.2V~3.3V 1.8V~5.5V 2 Auto Direction Detection Bidirectional Push-Pull、Open-drain VSSOP-8 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersBAV99
SOT-231 Pair Series Connection 1.25V@150mA 100V 215mA 250mW 4A 4ns 500nA@80V SOT-23 Switching Diodes ROHSNexperiaSwitching DiodesBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsXF-506P
插件1 15A 250V Blade 插件 Fuseholders ROHSXFCNFuseholdersS10MC
SMCDiodes - General Purposehongjiacheng
README
README.mdNano RC12-3
- uses a Nano (with ENC28J60 Ethernet shield) & an on-board mounted Cytron for rate control
- 1 or 2 MD13S for rate control
- self assembled through-hole board, least expensive
- controls two rates
- can be connected to a relay module with a 20 pin cable or dupont connectors
- work switch
- pressure switch
- [OSHPARK](https://oshpark.com/shared_projects/UU8e90h9
Teensy 4.1 RC11-2
- uses a Teensy & an on-board mounted Cytron for rate control
- small components are surface mount parts
- Teensy Ethernet
- can control two rates and eight sections
- 8 relays (SPDT 12V output)
- (1) 5V or 12V analog (pressure) input, potentiometer adjustable filtering
- (2) optically isolated digital (rate/pulse) inputs (5V or 12V)
- 3.3V I2C headers (Qwiic)
- supports optional external RelayDriver5 I2C board
- work switch
- canbus
ESP32 RC15
- uses an ESP32 (optional W5500 Ethernet Module)
- mostly surface mount parts
- can control two rates and 7-14 sections
- (2) DRV8870 motor drivers with reversible outputs for rates
- (7) DRV8870 motor drivers for 7 reversible (motorized ball valve) outputs
- (4) 5V analog inputs (or 2 differential inputs)
- (2) optically isolated digital (rate/pulse) inputs, up to 12V
- RS485 chip & header
- 3.3V I2C header
- supports optional external RelayDriver5 I2C board

- supports optional external RelayDriver5 I2C board
RelayDriver5
- PCA9535 based I2C IO expander
- designed to plug into 8 or 16 channel relay board with Qwiic cable

Firmware
Parts
93| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C3, C6, C9, C15, C17, C31, C33, C34, C35, C40, C41, C42, C43, C48 |
| 9 | 47uF | Capacitor_SMD:CP_Elec_6.3x5.4 | C2, C16, C37, C38, C39, C44, C45, C46, C47 |
| 9 | DRV8870DDA | Package_SO:Texas_HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalVias | U2, U5, U8, U9, U10, U11, U12, U13, U14 |
| 4 | MountingHole:MountingHole_3.2mm_M3 | , , , | |
| 4 | BAV99 | Package_TO_SOT_SMD:SOT-23 | D5, D6, D7, D8 |
| 3 | 22uF | Capacitor_SMD:C_0603_1608Metric | C5, C11, C13 |
| 2 | 10K | Resistor_SMD:R_0603_1608Metric | R4, R22 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C7, C14 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C4, C8 |
| 2 | 2.2K | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 2.7K | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 217 | Resistor_SMD:R_0603_1608Metric | R27, R28 |
| 2 | 341 | Resistor_SMD:R_0603_1608Metric | R24, R25 |
| 2 | AZ1117 | Package_TO_SOT_SMD:SOT-223 | IC1, IC4 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | Conn_01x06_Socket | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J7, J10 |
| 2 | PC817 chip | digikey-footprints:SMD-4_4.6x7.62mm_P2.54mm | U1, U4 |
| 1 | 105133-0011 | MyFootprints:MOLEX_105133-0011 | J1 |
| 1 | 120 | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 12V | MyFootprints:PowerPin | J5 |
| 1 | 200K | Resistor_SMD:R_0603_1608Metric | R26 |
| 1 | 330uF | Capacitor_SMD:CP_Elec_10x10.5 | C12 |
| 1 | 470uF | Capacitor_SMD:CP_Elec_10x10.5 | C10 |
| 1 | 500 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 776087-1-776087-1 | MyFootprints:7760871 | J2 |
| 1 | ADS1115IDGS | Package_SO:TSSOP-10_3x3mm_P0.5mm | U16 |
| 1 | C492610 | MyFootprints:Fuse_Holder_C492610 | F1 |
| 1 | C9943 | footprints:21-0041B_8_MXM | U7 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U3 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | ESP32-WROOM-32U | ESP32-WROOM-32U:XCVR_ESP32-WROOM-32U | U15 |
| 1 | Ground | MyFootprints:PowerPin | J6 |
| 1 | I2C | MyFootprints:Qwic_vertical | J9 |
| 1 | KF142V-5.0-6P | MyFootprints:KF142V-5.08-6P | KF3 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LOGO | MyFootprints:QwiicLogo | G*** |
| 1 | M7 - C95872 | MyFootprints:DO-214AC | D4 |
| 1 | PCA9306DCUR | MyFootprints:PCA9306DCUR | IC3 |
| 1 | PCA9685PW | Package_SO:TSSOP-28_4.4x9.7mm_P0.65mm | U6 |
| 1 | S10MC | MyFootprints:D_SMC_larger_pads | D3 |
| 1 | SMDRI127-330MT | MyFootprints:TMPA1265SP-101MN-D | L1 |
| 1 | SS36 | MyFootprints:SMA(DO-214AC) | D2 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-3-5.0-H_1x03_P5.00mm_Horizontal | J8 |
| 1 | XL2596 | MyFootprints:TO263-5L | IC2 |
More from AgOpenGPS-Official/Rate_Control
5- 4 layers159 × 130 mm

- 2 layers89 × 100 mm

- 2 layers110 × 54 mm

- 2 layers89 × 52 mm

- 2 layers28 × 18 mm

Similar boards
- 2 layers165 × 127 mm

YF1
SK21/YieldFlo
YieldFlo is a combine yield and moisture monitoring system that works alongside AgOpenGPS. A Windows desktop app records yield rate, moisture, and GPS position continuously while harvesting, and produces spatial yield…
60 parts5GPL-3.0 - 2 layers157 × 88 mm

RC17
lansalot/AOG_Dev
Like AgOpenGPS but not. This version is constantly under development.
111 partsGPL-3.0 - 2 layers165 × 127 mm

- 2 layers76 × 76 mm

- 4 layers64.6 × 55.2 mm

Whisker
HeyPCB/whisker
Drop-in controller for Petoi's Nybble robot cat running the stock OpenCat firmware: ATmega328P, PCA9685, MPU-6050, USB-C, 3 A buck, protected battery input. 4-layer KiCad 10 board plus printed cradle.
118 partsCERN-OHL-S-2.0 - 2 layers67.3 × 96.9 mm

WaterQualityControl
Hasatio/WaterQualityControl
The circuit taken as an example while designing the board Adafruit PCA9685
142 parts - 4 layers90 × 90 mm

CDFR2027-Carte Arduino
robotronik/CDFR2027-Carte-Arduino
La carte Arduino Controle de moteur pour CDFR 2027
85 parts - 4 layers83 × 67.5 mm

MarineBoard
Cadburies/SisuAssistant
Sailing yacht Sisu: Home Assistant + ESPHome Marine Board (alternator regulation, tanks) + MQTT kernel, Signal K/Grafana/InfluxDB on a NAS, and Sisu Nav chart & weather-routing cockpit.
162 parts1Apache-2.0
Questions
How big is the RC15 PCB?
It measures 145 × 108 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RC15 use?
93 parts, built around the MAX3485EESA+T, CH340C, ESP32-WROOM-32U and DRV8870DDA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RC15 KiCad files?
From the AgOpenGPS-Official/Rate_Control repository on GitHub, at the commit this page was made from: the board is ESP32/RC15/RC15.kicad_pcb and its schematic ESP32/RC15/Analog.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the RC15 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).