

ZoM Model A
An open-source FPGA-based EMS SPECTRE video synth
- Size
- 75 × 40 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 145
- Nets
- 295
- Pads
- 917
- Tracks, vias
- 2,167, 329
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 15 May 2025
- Updated
- 15 Jun 2025
Overview
ZoM Model A is an open-source printed circuit board by ademenev, from the ademenev/open_spectre repository on GitHub. It is a 6-layer board of 75 × 40 mm with 145 parts on 295 nets, routed with 2,167 tracks and 329 vias.
It is built around the XA7Z020-1CLG400I, EN5311QI and W25Q256FVBIG TR, with the ATSHA204A-STUCZ-T, SIT8008AI-73-XXS-33.333333E and BKP0603HS121-T among its other parts. Its parts include 65 capacitors, 42 resistors, 9 ICs, 7 connectors and 4 inductors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
9XA7Z020-1CLG400I
CSPBGA-400-40℃~+100℃ 1.2V~3.3V 12bit 130 256KB 32 Bit 667MHz ARM Cortex-ASeries Power-on reset (POR)、Watchdog reset、Software reset、Built-in general-purpose timer、Built-in temperature sensor、Hardware ECC check、Hardware parity check、Storage encryption、Integrated PLL clock generator CSPBGA-400 Microcontrollers (MCU/MPU/SOC) ROHSAMD/XILINXMicrocontrollers (MCU/MPU/SOC)EN5311QI
QFN-20-EP(4x5)-40℃~+85℃ 1 1.1mm 1A 1uA 2.4V~6.6V 4MHz 4mm 5mVp-p 5mm 600mV~6V 700uF 94% Short Circuit Protection、Over Current Protection、Under Voltage Protection、Overheat Protection、Automatic fault recovery、Synchronous rectification control、Dynamic voltage scaling QFN-20-EP(4x5) Isolated Power Modules ROHSIntel/AlteraIsolated Power ModulesW25Q256FVBIG TR
TFBGA-24(6x8)-40℃~+85℃ 100,000 cycles 104MHz 1uA 2.7V~3.6V 20 Years 256Mbit Power-on reset、Hardware Write Protection、Software Write Protection、Write enable latch、Absolute Write Protection SPI TFBGA-24(6x8) NOR FLASH ROHSWinbond ElecNOR FLASHATSHA204A-STUCZ-T
SOT-23-40℃~+85℃ 150nA 2V~5.5V I2C、1-Wire SHA-256 SOT-23 Security Verification / Encryption ICs ROHSMicrochip TechnologySecurity Verification / Encryption ICsSIT8008AI-73-XXS-33.333333E
SMD2016-4P-40℃~+85℃ 2.25V~3.63V 33.333332MHz 4.5mA LVCMOS、HCMOS ±50ppm SMD2016-4P Programmable Oscillators ROHSSiTimeProgrammable OscillatorsBKP0603HS121-T
0201-55℃~+85℃ 1 120Ω@100MHz 150mΩ 850mA ±25% 0201 Ferrite Beads ROHSTaiyo YudenFerrite BeadsCHS-04TA
SMD-40℃~+85℃ 100mA 4 6V Black J-Lead SPST Slide, Recessed SMD DIP Switches ROHSNidecDIP SwitchesSCHD3A0100
SMDUncategorisedALPSALPINEU.FL-R-SMT-1
Up to 6GHz Ultra Small Surface Mount Male Coaxial Connectors U.FL SeriesHirose ElectricUncategorised
README
README.mdOPEN_SPECTRE
An open-source FPGA-based EMS SPECTRE video synth.
A project aimed at recreating the EMS SPECTRE VIDEO SYNTHESIZER in HDL
Open to donations and contributors with FPGA experience. 😀
✨The EMS SPECTRE Colour Video ✨
Synthesizer is a unique and revolutionary new product: an instrument capable of producing exciting graphic images on an ordinary television screen. The complete SPECTRE package consists of the synthesizer itself, plus a Sony Trinitron colour monitor, and a Sony black-and-white TV camera. The synthesizer is compact (38"x23.5"x7"), portable (about 35 pounds/15.9KG), and unequalled in its simplicity and versatility.

Design Info
🎉Aim 🎉
The aim of this project is to preserve this rare and unique video synth by recreating it in an FPGA, but also to use it as a building block to make a Spectre that is both true to the original and also a modern tool for creativity. For more info in this process take a look at: Cloning Hardware Ethos
🍣Want to Contribute?🍣
Amazing! If you have FPGA and or Verilog/VHDL skills we would love to have you involved. But, first, there are a few things you should know.
What to do first
- Look through the resources folder to get an idea of what the EMS SPECTRE is and how it works
- Look at the top-level diagram and the list of modules
Project Details For Contributors
- RTL in VHDL or Verilog (VHDL preferred, no system Verilog 😎 sorry)
- One module per file with a separate testbench (Verilog or VHDL test benches only, *not everything has one yet, but it should)
- Test benches should print out a message at the end confirming if they are successful or not
- No HSL or auto-generated code, no busses or interfaces for now (will be busses later)
- Use any software you like, but a Vivado project will be supplied
- Follow the template for file headers and comments 📑
- Follow the folder structure for the project 📂
- All code must be open source or MIT license 👍
If after all that you still want to be involved you can do one of three things:
- Email us at OPEN.SPECTRE.PROJECT@gmail.com and see what modules we need to make at the moment
- Branch the repo, make a module, and submit a pull request
- If you are not any good at git/GitHub, if you write any modules you can email them to us and we will integrate them into the project
🐙License🐙
Creative Commons CC BY-NC
Contributors
-Remi Freer -Jacob Stoker -Robert D Jordan
Donations
We are very thankful to have received donations from the following people: Chris Korvin, Jay Hotchin, Milton Grimshaw, and more amazing anonymous people.
Parts
145| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 470nF | B:_AD_adlib_lib_pcb_TE-IPC7351_CAPC0603X33N.PcbLib_CAPC0603X33N | C3, C4, C12, C13, C14, C15, C18, C19, C20, C22, C31, C32, C33, C38, C39, C40 +3 |
| 17 | 10K | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC0603X26N.PcbLib_RESC0603X26N | R5, R11, R12, R13, R16, R17, R18, R19, R20, R21, R22, R28, R29, R30, R39, R40 +1 |
| 15 | 470nF | dbww.dblib/Capacitor_0603_0201_:CAPC0603X33N | C1, C8, C23, C34, C35, C36, C37, C41, C43, C44, C45, C46, C47, C48, C50 |
| 9 | 47µF | B:_AD_adlib_lib_pcb_TE-IPC7351_CAPC3216X180N.PcbLib_CAPC3216X180N | C9, C16, C21, C25, C27, C28, C29, C30, C42 |
| 8 | 4.7µF | B:_AD_adlib_lib_pcb_TE-IPC7351_CAPC1005X60N.PcbLib_CAPC1005X60N | C2, C5, C10, C11, C17, C24, C26, C63 |
| 7 | 4.7µF | D:_svn_cad_altium_pcb_contract_tt_tt-svn_ADLIB_dbww_.._lib_pcb_TE-IPC7351_CAPC1005X60N.PcbLib_CAPC1005X60N | C49, C51, C52, C53, C54, C55, C56 |
| 6 | FIDU-DOT - small | dbww.dblib:FIDU-DOT - small | PM1, PM2, PM3, PM4, PM5, PM6 |
| 5 | TP | B:_tfx_altium_lib_common_PCB_TP_TP-SMD-2mm.PcbLib_TP-SMD-2mm | TP1, TP2, TP3, TP4, TP5 |
| 4 | 470R | TE.DbLib/R_1005_0402:RESC1005X40N | R3, R7, R24, R31 |
| 3 | 100µF | TE.DbLib/C_3216_1206:CAPC3216X180N | C59, C60, C61 |
| 3 | 10K | TE.DbLib/R_0603_0201:RESC0603X26N | R2, R9, R10 |
| 3 | 33R | TE.DbLib/R_0603_0201:RESC0603X26N | R1, R4, R8 |
| 3 | 33R | B:_AD_adlib_lib_pcb_TE-IPC7351_RESCAX50P100X200X55-8N.PcbLib_RESCAX50P100X200X55-8N | R34, R35, R42 |
| 2 | 0 | ZoM-Model-A.PcbLib:RESC0603X26N | R14, R15 |
| 2 | 33R | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC0603X26N.PcbLib_RESC0603X26N | R26, R27 |
| 2 | 4.7µF | TE.DbLib/C_1005_0402:CAPC1005X60N | C57, C58 |
| 2 | 470nF | ZoM-Model-A.PcbLib:CAPC0603X33N | C64, C65 |
| 2 | 4K7 | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC0603X26N.PcbLib_RESC0603X26N | R23, R37 |
| 2 | EN5311QI | B:_AD_adlib_lib_pcb_TE_EN5311QI.PcbLib_EN5311QI | U7, U8 |
| 2 | IND-Ferrite | TiWi-uB2.PcbLib:RESC1005X40R | L2, L3 |
| 2 | W25Q256FVBIG | B:_AD_adlib_lib_pcb_TE-IPC7351_BGA24C100P5X5_800X600X120N.PcbLib_BGA24C100P5X5_800X600X120N | U3, U4 |
| 1 | 0R | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC1005X40N.PcbLib_RESC1005X40N | R41 |
| 1 | 200K | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC1005X40N.PcbLib_RESC1005X40N | R32 |
| 1 | 301K | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC1005X40N.PcbLib_RESC1005X40N | R33 |
| 1 | 470R | B:_AD_adlib_lib_pcb_TE-IPC7351_RESC1005X40N.PcbLib_RESC1005X40N | R25 |
| 1 | 4K7 | TE.DbLib/R_0603_0201:RESC0603X26N | R38 |
| 1 | 4pin button | B:_tfx_altium_lib_common_pcb_BUT-SW_KMS221G_LFS.PcbLib_KMS221G_LFS | SW1 |
| 1 | 680R | TE.DbLib/R_1005_0402:RESC1005X40N | R36 |
| 1 | ATSHA204A-STUCZ-T | B:_AD_adlib_lib_pcb_TE-IPC7351_SOT95P237X112-3N.PcbLib_SOT95P237X112-3N | U6 |
| 1 | Antena 2450AT43B100 | TiWi-uB2.PcbLib:Antena 2450AT43B100 | ANT1 |
| 1 | Atmel AVR ATtiny10 | B:_tfx_altium_lib_common_pcb_IC_IPC_SOT23-6.PcbLib_SOT23-6 | IC1 |
| 1 | BKP0603HS121-T | TE.DbLib/L_0603_0201:INDC0603X33N | L1 |
| 1 | BKP0603HS121-T | B:_AD_adlib_lib_pcb_TE-IPC7351_INDC0603X33N.PcbLib_INDC0603X33N | L4 |
| 1 | CHS-04TA | B:_AD_adlib_lib_pcb_TE-IPC7351_CHS-04TA.PcbLib_CHS-04TA | S3 |
| 1 | LED Green SML-P11MTT86 | B:_AD_adlib_lib_pcb_TE-IPC7351_LEDC1006X25N_GREEN.PcbLib_LEDC1006X25N_GREEN | D3 |
| 1 | LED Red SML-P11UTT86 | B:_AD_adlib_lib_pcb_TE-IPC7351_LEDC1006X25N_RED.PcbLib_LEDC1006X25N_RED | D1 |
| 1 | MMC SD Socket | B:_AD_adlib_lib_pcb_TE_104C-TAA0-R.PcbLib_104C-TAA0-R | J2 |
| 1 | Mount.Hole 3.2mm | dbww.dblib:MHole3_2mm | H1 |
| 1 | Mount.Hole 3.2mm | TE.DbLib:MHole3_2mm | H4 |
| 1 | PMod 2x6 Socket 90° | B:_AD_adlib_lib_pcb_TE_PMod2x6.PcbLib_PMod2x6 | J8 |
| 1 | SCHD3A0100 | B:_AD_adlib_lib_pcb_TE_SCHD3A0100.PcbLib_SCHD3A0100 | J4 |
| 1 | STIFTLEISTE2.54 OG 2R-8 | TE.DbLib:STIFTLEISTE2_54 OG 2R-8 | J5 |
| 1 | SiT8008AI-73-XXS-33.333333E | TE.DbLib/CLK:2016 | U1 |
| 1 | Stiftleiste versetzt 1-reihig, 6pol. | B:_AD_adlib_lib_pcb_TE_STIFTLEISTE2_54 OG 1R-6V.PcbLib_STIFTLEISTE2_54 OG 1R-6V | J7 |
| 1 | TiWi-uB2 | TiWi-uB2.PcbLib:TiWi-uB2 | U5 |
| 1 | U.FL-R-SMT-1 | B:_AD_adlib_lib_pcb_TE_U.FL-R-SMT-1.PcbLib_U.FL-R-SMT-1 | J3 |
| 1 | WANNE2,54-50 GERADE | B:_AD_adlib_lib_pcb_TE_WANNE2,54-50 GERADE.PcbLib_WANNE2,54-50 GERADE | J1 |
| 1 | XA7Z020-1CLG400I | B:_AD_adlib_lib_pcb_TE-IPC7351_BGA400C80P20X20_1700X1700X160N.PcbLib_BGA400C80P20X20_1700X1700X160N | U2 |
More from ademenev/open_spectre
1- 2 layers169.5 × 127 mm

Similar boards
- 4 layers94 × 50.8 mm

- 2 layers30 × 30 mm

ReCamera Gimbal
Seeed-Studio/OSHW-reCamera-Series
reCamera is a series of open-source AI cameras.
123 parts495Apache-2.0 - 4 layers21 × 17.8 mm

XIAO ESP32 C6
MitkoDyakov/Calipatron
I design my own digital caliper based on STM32F103C8T6 blue pill.
83 parts47MIT - 2 layers

Hw33 axis3 nn02201 d21p87
Alexey-Lukin/silken_net
Silken Net: A decentralized Nature-as-a-Service (NaaS) platform. Bridges edge computing IoT sensors in forests with Polygon blockchain via an Oracle to mint Carbon and Forest Coins based on real-time biological…
6 parts23AGPL-3.0 - 4 layers46.1 × 45.6 mm

Avionics mainboard
AFS-pt/PROMETHEUS-1
Documentation lives here: https://afs-pt.github.io/PROMETHEUS-1
202 parts15 - 4 layers22.9 × 50.8 mm

Penguino STM32WL M
azerimaker/Penguino-STM32WL-MAMWLExx
This repo contains all the necessary design and fabrication files for the MoveSolution's MAMWLExx based Penguino STM32WL breakout board.
68 parts15 - 6 layers50 × 50 mm

- 4 layers22.9 × 50.8 mm

Penguino Feather-4260-v1
azerimaker/Penguino-RAK4260
This repo contains all the necessary design and fabrication files for the RAK4260 based Penguino SAMR34 Feather breakout board.
60 parts8
Questions
How big is the ZoM Model A PCB?
It measures 75 × 40 mm and has 6 copper layers, 1.6 mm thick.
What parts does the ZoM Model A use?
145 parts, built around the XA7Z020-1CLG400I, EN5311QI, W25Q256FVBIG TR and ATSHA204A-STUCZ-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ZoM Model A KiCad files?
From the ademenev/open_spectre repository on GitHub, at the commit this page was made from: the board is fpga/hw/legacy/kicad_zynq_template/ZoM-Model-A.kicad_pcb and its schematic fpga/hw/QM_tech_proto/Artix_hw_proto.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ZoM Model A design in my own project?
Its repository states no licence, so its author keeps all rights: ask ademenev before reusing the design.