

Pulser3
After creation, open KiCad and work in boards/ /.
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 102
- Pads
- 244
- Tracks, vias
- 39, 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 16 Apr 2026
- Updated
- 17 Aug 2026
Overview
Pulser3 is an open-source printed circuit board by aaritkoundinya, from the aaritkoundinya/Pulse repository on GitHub. It is a 4-layer board with 48 parts on 102 nets, routed with 39 tracks and 4 vias.
It is built around the RP2040, DPS310XTSA1 and TPS5405D, with the W25Q128JVEIQ and BNO055 among its other parts. Its parts include 20 capacitors, 14 resistors, 8 connectors, 5 ICs and 1 crystal. It belongs with the RP2040 boards of this library.
Main components
5RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)DPS310XTSA1
VLGA-8-40℃~+85℃ 0.5pa/K 1.7V~3.6V 100pa 27.6ms 30Kpa~1.2bar 500nA 6pa I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode VLGA-8 Pressure Sensors ROHSInfineon TechnologiesPressure SensorsTPS5405D
SOIC-8-40℃~+85℃@(TA) 1 1.1MHz 100uA 2A 5V 6.5V~28V Buck Buck Built-in Fixed No SOIC-8 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersW25Q128JVEIQ
WSON-8-EP(6x8)-40℃~+85℃ 100,000 cycles 10uA 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(6x8) NOR FLASH ROHSWinbondNAND FLASHBNO055
LGA-28(3.8x5.2)-40℃~+85℃ 2.4V~3.6V 40uA I2C、UART IMU X,Y,Z X,Y,Z ±16g ±2000dps LGA-28(3.8x5.2) Accelerometers ROHSBosch SensortecAccelerometers
README
README.mdPulse
A multiuse flight computer.
Repository Structure
boards/rX/- a board revisiontemplates/scratch-board/- starter template for clean-slate revisionstools/new_revision.sh- helper script to create new revisions
Create New Revisions
To build from an existing revision:
./tools/new_revision.sh r3 --from r2.1To Start from scratch:
./tools/new_revision.sh r3 --scratchAfter creation, open KiCad and work in boards/<revision>/.
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C3, C11, C12, C15, C16, C17, C18, C19 |
| 4 | 10K | Resistor_SMD:R_0603_1608Metric | R5, R7, R9, R10 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric | C7, C10, C13, C14 |
| 4 | 4.7K | Resistor_SMD:R_0603_1608Metric | R11, R12, R13, R14 |
| 4 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3, J4, J5, J6 |
| 3 | 100nF | Capacitor_SMD:C_0805_2012Metric | C5, C8, C9 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | Screw_Terminal_01x04 | TerminalBlock:TerminalBlock_Xinya_XY308-2.54-4P_1x04_P2.54mm_Horizontal | J7, J8 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 12 MHZ | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 120nF | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 3.3K | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | BNO055 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U2 |
| 1 | C | Capacitor_SMD:C_0805_2012Metric | C20 |
| 1 | DPS310XTSA1 | Sensor_Pressure:XDCR_DPS310XTSA1 | U3 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3D-SF | J2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | TPS5405 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | W25Q128JVE | Package_SON:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm | U4 |
More from aaritkoundinya/Pulse
3Similar boards
- 2 layers143 × 40.6 mm

- 4 layers50.8 × 25.4 mm

- 4 layers17.8 × 41.9 mm

- 4 layers75 × 55 mm

HIDMorph
cedarhacks/HIDMorph
Hardware/Firmware of HIDMorph, a lua configurable HID translation/generation device
50 parts4 - 2 layers323.9 × 115.5 mm

- 2 layers33.3 × 36.5 mm

Mic
joshitha-c/microphone
A compact USB digital microphone development board built around the Raspberry Pi RP2040 microcontroller and the STMicroelectronics MP34DT05TR-A digital MEMS microphone.
28 parts - 4 layers62.3 × 29.5 mm

Motokit controlsystem v2
S0L1DDEV/motormod-pcb-controlsystem
CFMoto lightkit mod, driving a lightkit based on engine information read through CAN. This PCB is part of the system responsible for reading frames and outputting a animation on a neopixel lightstrip
59 parts - 4 layers74 × 44 mm

Motorkit display
S0L1DDEV/motormod-pcb-display
CFMoto lightkit mod, driving a lightkit based on engine information read through CAN. This PCB is part of the system responsible for driving a very basic user interface that allows for top level control of the light…
37 parts
Questions
What parts does the Pulser3 use?
48 parts, built around the RP2040, DPS310XTSA1, TPS5405D and W25Q128JVEIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pulser3 KiCad files?
From the aaritkoundinya/Pulse repository on GitHub, at the commit this page was made from: the board is boards/r2/pulser3/pulser3.kicad_pcb and its schematic boards/r2.1/pulser2.1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pulser3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask aaritkoundinya before reusing the design.

