S0L1DDEV/motormod-pcb-controlsystemCFMoto lightkit mod, driving a lightkit based on engine information read through CAN. This PCB is part of the system responsible for reading frames and outputting a animation on a neopixel lightstrip
Motokit controlsystem v2 is an open-source printed circuit board by S0L1DDEV, from the S0L1DDEV/motormod-pcb-controlsystem repository on GitHub. It is a 4-layer board of 62.3 × 29.5 mm with 59 parts on 76 nets, routed with 387 tracks and 75 vias.
It is built around the RP2040, 74AHCT1G125SE and BD9D320EFJ-E2, with the W25Q128JVEIQ and ESD351DPYR among its other parts. Its parts include 28 capacitors, 7 ICs, 6 resistors, 4 diodes and 4 connectors. It belongs with the RP2040 boards of this library.
Working on the pcb for the controlsystems
| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C6, C7, C8, C10, C12, C13, C14, C20, C21, C28 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C9, C11, C24, C27 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C18, C19 |
| 2 | 15pF | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | 22uF | Capacitor_SMD:C_0805_2012Metric | C25, C26 |
| 2 | ESD351DPYR | locallib:TVS-2_L1.0-W0.6-P0.65-RD-1 | D1, D2 |
| 2 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1, JP2 |
| 1 | 10K | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C23 |
| 1 | 120E | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 120K | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 12MHz | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1 |
| 1 | 16Vrwm, 17.8Vbr | Diode_SMD:D_SMA | D4 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 220uF | Capacitor_THT:C_Radial_D6.3mm_H11.0mm_P2.50mm | C17 |
| 1 | 22K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 3.3uH | locallib:IND-SMD_L7.1-W6.6_SL0624 | L1 |
| 1 | 3A | locallib:FUSE-SMD_L9.0-W7.0 | F1 |
| 1 | 470E | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 74AHCT1G125 | locallib:SOT65P210X110-5N | U5 |
| 1 | BD9D320EFJ-E2 | locallib:SOIC127P600X100-9N | U6 |
| 1 | CAN | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1 |
| 1 | D_Schottky | Diode_SMD:D_SMA | D3 |
| 1 | INTERFACE | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J3 |
| 1 | LDK130PU33R_DFN6 | locallib:LDO-6_1.3x1.2mm_P0.4mm | U7 |
| 1 | LOGO | LOGO | G*** |
| 1 | MCP2515-xST | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | MCP2562-E-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | NC | Capacitor_SMD:C_0603_1608Metric | C22 |
| 1 | NEOPIXEL | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U4 |
| 1 | SWD | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J4 |
| 1 | W25Q128JVE | locallib:WSON-8-1EP_8x6mm_P1.27mm_EP3.4x4.3mm | U3 |
The 55 most common of 59 parts.
S0L1DDEV/motormod-pcb-controlsystem
CFMoto lightkit mod, driving a lightkit based on engine information read through CAN. This PCB is part of the system responsible for reading frames and outputting a animation on a neopixel lightstrip
MatthiasGeorgImhof/STMF405_Flight_Controller
A flight controller inspired by Speedybee F405 v3 but with CAN and flash memory instead of flash card.
MatthiasGeorgImhof/STMF765_Flight_Controller
A flight controller inspired by Speedybee F405 v3 but with CAN using F7 MCU. Use flash memory instead of flash card.
ZeniteSolar/MCC22
Follow the steps below, if any value differs from the expected, abort the test. Power off and on after each step. Always limit the power source to 18V at 100mA. Use this link to find components on the board.
holison-001/MVP-PPG
기존 PPG와 전선 6개로 연결하는 전이중 RS-422 ↔ 3.3V UART 변환 보드다. 같은 작업 폴더에 별도 KiCad 프로젝트로 작성했다. 외부 9V를 PPG와 공유하고, 사용자 지정 LD1117-3.3V로 이 보드의 통신부와 UART 포트용 3.3V를 만든다. MCU는 추가하지 않는다.
It measures 62.3 × 29.5 mm and has 4 copper layers, 1.6 mm thick.
59 parts, built around the RP2040, 74AHCT1G125SE, BD9D320EFJ-E2 and W25Q128JVEIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the S0L1DDEV/motormod-pcb-controlsystem repository on GitHub, at the commit this page was made from: the board is motokit-controlsystem-v2/motokit-controlsystem-v2.kicad_pcb and its schematic motokit-controlsystem-v2/motokit-controlsystem-v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask S0L1DDEV before reusing the design.