Skip to the content
2 layers80.7 × 83.7 mmSumo, the printed circuit board in 3D

This is a SUMO robot for comperitions.

Size
80.7 × 83.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
38
Nets
33
Pads
158
Tracks, vias
279, 7
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
5 Mar 2024
Updated
8 May 2025

Overview

Sumo is an open-source printed circuit board by Tonikiller10000, from the Tonikiller10000/RoboSumo repository on GitHub. It is a 2-layer board of 80.7 × 83.7 mm with 38 parts on 33 nets, routed with 279 tracks and 7 vias.

It is built around the ATMEGA328P-AU and ITR9608-F. Its parts include 14 resistors, 7 connectors, 6 capacitors, 4 ICs and 2 switches. It belongs with the robots and motor control boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

RoboSumo

Description:

This is a SUMO robot for comperitions. It pushes the opponent`s robot out of the ring.

It uses:

  • ATmega328p-AU as an microcontroller(used in arduino uno);
  • 16 or 20Mhz crystal resonator;
  • TB6612FNG DC motor driver;
  • VL53L0x distance sensor;
  • LI-PO battery (7.2V)
  • 2x DC motors with low torque high speed gear box
  • robot suport (Wood, 3d printed or any low weight matherial)

Schematic:

How it works:

The board is like a custom arduino UNO board powered from an 7.2V Li-Po battery trouth an 5V voltage regulator. 6 digital pins are used for the TB6612FNG motor driver witch is powered dirrectly from the battery to give more power to the motors. The reset pin has a 10K pullup resistor witch is pulled down by the reset button when it is pressed. The UART and ICSP pins wore pulled out to program the code and the bootloader of the IC. For now I will try to use the VL53L0x I2C distance sensor, because other sensors are a little to slow.

Programming:

Programming of the robot is done via UART protocoll with an FTDI programming board. The code for the RoboSumo is not ready.

Design and mentions

This is The model I followed and some tips:

  • to reach better torque on the wheels, it should be wider.
  • to mount the motors use molderd plastic motor holders, or be carefull when printing it.
  • the case was made with autodesk fusion 360 at the 3d printer and with some M3 screws.

The next version will have the motor driver soldered on the board and motors screwed dirrectly to it as the suport. Also I will try to make a smaller version

Links:

  • ATmega328p-AU (microcontroller):
  • LM78L05 (5V voltage regulator):

Parts

38
QtyValueFootprintReferences
51KResistor_SMD:R_1206_3216MetricR2, R20, R20, R20, R20
42KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R1, R1, R1
3100uFCapacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolderC1, C1, C2
2100nFCapacitor_SMD:C_0805_2012MetricC3, C3
2220RResistor_SMD:R_1206_3216MetricR3, R5
247KResistor_SMD:R_1206_3216MetricR4, R6
2ITR9608-FOptoDevice:Everlight_ITR9608-FU4, U5
110KResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1
120MHzCrystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mmY1
14.7uFCapacitor_SMD:C_0805_2012MetricC3
1ATmega328P-AU TQFP32_32A_MCHU1
1BATConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1
1BATConnector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ8
1Conn_01x03Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_VerticalJ9
1Conn_01x06_MountingPinConnector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_VerticalJ4
1ICSPConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ2
1LM78L05_TO9278L05:PK(R-PSSO-F3)U2
1MotAConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_HorizontalJ7
1MotBConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_HorizontalJ6
1POWLED_SMD:LED_PLCC_2835D1
1RESETButton_Switch_THT:SW_CuK_OS102011MA1QN1_SPDT_AngledSW1
1RESETButton_Switch_THT:SW_PUSH_6mmSW2

The 35 most common of 38 parts.

More from Tonikiller10000/RoboSumo

1
  • 2 layers38.5 × 48.5 mmSumo, the printed circuit board in 3D

    Sumo

    Tonikiller10000/RoboSumo

    This is a SUMO robot for comperitions.

    30 parts1

Similar boards

  • 2 layers54 × 60 mmMicroPAMI-2026, the printed circuit board in 3D

    MicroPAMI-2026

    LesKaribous/Karibous-2026-PAMI

    39 parts1
  • 2 layers27 × 60 mmOpenFMS, the printed circuit board in 3D

    OpenFMS

    aasmr/openFMS

    Open-source filament presence and motion sensor for Klipper 3D printers – includes MCU firmware, PCB design, and 3D printable parts.

    41 partsMIT
  • 2 layersSensor, the printed circuit board in 3D

    Sensor

    Ahey0/Micro_Lab8

    10 parts
  • 2 layers24.5 × 33.5 mmInfill pcb, the printed circuit board in 3D

    Infill pcb

    JeffreyWangDev/infill-pcb

    15 parts
  • 2 layers80 × 100 mmAirstream controller, the printed circuit board in 3D

    Airstream controller

    klaus-liebler/self-balancing_robot

    hardware and software for a super cheap self balancing robot

    77 partsMIT
  • 2 layers109.4 × 51 mmTachometer, the printed circuit board in 3D

    Tachometer

    MITEngine/stirling-engine

    Stirling Engine

    32 parts
  • 2 layers66 × 24 mmImu rc car encoders, the printed circuit board in 3D

    Imu rc car encoders

    DimitriOnLSD/imu-rc

    Gesture-based RC car controller using ESP32-S3, BLE, LSM6DSO IMU, OLED display, and LiPo battery with USB-C charging.

    23 parts7MIT

Questions

How big is the Sumo PCB?

It measures 80.7 × 83.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Sumo use?

38 parts, built around the ATMEGA328P-AU and ITR9608-F. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Sumo KiCad files?

From the Tonikiller10000/RoboSumo repository on GitHub, at the commit this page was made from: the board is RoboSumoV0.3/Sumo.kicad_pcb and its schematic RoboSumoV0.3/Sumo.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Sumo design in my own project?

Its repository states no licence, so its author keeps all rights: ask Tonikiller10000 before reusing the design.