2 layers
2 layers
Project Door Controll BLUETHOOTH
Ahey0/Micro_Lab_Project- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 29
- Nets
- 93
- Pads
- 166
- Tracks, vias
- 178, 10
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 29 May 2025
- Updated
- 29 May 2025
Overview
Project Door Controll BLUETHOOTH is an open-source printed circuit board by Ahey0, from the Ahey0/Micro_Lab_Project repository on GitHub. It is a 2-layer board with 29 parts on 93 nets, routed with 178 tracks and 10 vias.
It is built around the ATMEGA162V-8PU, HC-05 and AMS1117-3.3, with the ITR9608-F and ULN2803A among its other parts. Its parts include 7 capacitors, 7 resistors, 6 ICs, 5 diodes and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5
ATMEGA162V-8PU
PDIP-40-40℃~+85℃ 1.8V~5.5V 16KB 1KB 35 512Byte 8 Bit 8MHz AVR Built-in FLASH PDIP-40 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
HC-05
Bluetooth to Serial Port ModuleGENERICUncategorised
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
ITR9608-F
DIP-4-25℃~+85℃ 1.2V 15us 15us 20mA 5mm 940nm DIP-4 Photointerrupters - Slot Type - Transistor Output ROHSEverlight ElectronicsPhotointerrupters - Slot Type - Transistor Output
ULN2803A
SOP-18-300mil-40℃~+85℃ 0.93mA 100uA 15pF 20uA 30V 500mA 50V 8 SOP-18-300mil Darlington Transistor Arrays ROHSUMWDarlington Transistor Arrays
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 3.3k | Resistor_SMD:R_0402_1005Metric | R2, R3, R4, R5 |
| 4 | LED | LED_THT:LED_D3.0mm | D1, D2, D3, D4 |
| 2 | 22pf | Capacitor_SMD:C_0201_0603Metric | C1, C2 |
| 1 | 100nf | Capacitor_SMD:C_0201_0603Metric | C3 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 150 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R7 |
| 1 | 1k5 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6 |
| 1 | 1uf | Capacitor_SMD:C_0201_0603Metric | C6 |
| 1 | 22u | Capacitor_SMD:C_0402_1005Metric | C4 |
| 1 | 22uf | Capacitor_SMD:C_0201_0603Metric | C7 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | ATmega162V-8P | Package_DIP:DIP-40_W15.24mm | U1 |
| 1 | Crystal | Crystal:Crystal_SMD_EuroQuartz_EQ161-2Pin_3.2x1.5mm | Y1 |
| 1 | HC-05 | Added:HC-05 | U4 |
| 1 | ITR9608-F | OptoDevice:Everlight_ITR9608-F | U2 |
| 1 | L1 | Inductor_SMD:L_0201_0603Metric | 10u1 |
| 1 | LTC3525-5 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U6 |
| 1 | RED | LED_THT:LED_D5.0mm | D5 |
| 1 | Stepper_Motor_unipolar_6pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | M1 |
| 1 | To Sensor | Connector_PinHeader_1.00mm:PinHeader_1x02_P1.00mm_Vertical | J1 |
| 1 | ULN2803A | Package_DIP:DIP-16_W7.62mm_SMDSocket_SmallPads | U3 |
More from Ahey0/Micro_Lab_Project
1Similar boards
- 2 layers
- 2 layers54 × 60 mm
- 2 layers80.7 × 83.7 mm
- 2 layers27 × 60 mm
OpenFMS
aasmr/openFMS
Open-source filament presence and motion sensor for Klipper 3D printers – includes MCU firmware, PCB design, and 3D printable parts.
41 partsMIT - 2 layers24.5 × 33.5 mm
- 2 layers80 × 100 mm
Airstream controller
klaus-liebler/self-balancing_robot
hardware and software for a super cheap self balancing robot
77 partsMIT - 2 layers109.4 × 51 mm
- 2 layers66 × 24 mm
Imu rc car encoders
DimitriOnLSD/imu-rc
Gesture-based RC car controller using ESP32-S3, BLE, LSM6DSO IMU, OLED display, and LiPo battery with USB-C charging.
23 parts7MIT
Questions
What parts does the Project Door Controll BLUETHOOTH use?
29 parts, built around the ATMEGA162V-8PU, HC-05, AMS1117-3.3 and ITR9608-F. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Project Door Controll BLUETHOOTH KiCad files?
From the Ahey0/Micro_Lab_Project repository on GitHub, at the commit this page was made from: the board is Project_Door_Controll _Via_Bluetooth/Project_Door_Controll_BLUETHOOTH.kicad_pcb and its schematic Project_Door_Controll _Via_Bluetooth/Project_Door_Controll_BLUETHOOTH.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Project Door Controll BLUETHOOTH design in my own project?
Its repository states no licence, so its author keeps all rights: ask Ahey0 before reusing the design.