Skip to the content
2 layers25 × 15 mmTFI2CEXT01, the printed circuit board in 3D

I2C bus wire length extension module. Enabling the use of more extensive bus interconnection.

Size
25 × 15 mm
Copper layers
2
Thickness
1.6 mm
Parts
26
Nets
10
Pads
69
Tracks, vias
147, 47
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
3 Apr 2021
Updated
19 Jul 2024

Overview

TFI2CEXT01 is an open-source printed circuit board by ThunderFly-aerospace, from the ThunderFly-aerospace/TFI2CEXT01 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 25 × 15 mm with 26 parts on 10 nets, routed with 147 tracks and 47 vias.

It is built around the MIC5504-3.3YM5, TCA4307DGK and SM04B-GHS-TB, with the BZX585-B5V6,115-JSM among its other parts. Its parts include 6 resistors, 4 capacitors, 4 connectors, 3 diodes and 2 ICs. It belongs with the sensors and measurement and robots and motor control boards of this library.

Main components

4

README

README.md

TFI2CEXT01A - I²C bus extender

I²C bus extension module. This module allows an extension of the usable total length of the I2C bus on the UAV. Most I2C bus instances benefit from having TFI2CEXT positioned midway between master and slave, where its signal amplification is most effective in both directions.

Top view on I2C bus extender

Bottom view on I2C bus extender

In practice, I2C devices vary in driving capability, and I2C signals are often affected by capacitive load or unwanted signal coupling. TFI2CEXT can effectively isolate bus segments, ensuring devices only see the segment's wiring load up to the TFI2CEXT. Thus, placing TFI2CEXT closer to the "problematic" I²C device is optimal.

Where to get it?

ThunderFly TFI2CEXT01A counter is commercially available from ThunderFly s.r.o., write an email to info@thunderfly.cz. Or shop it on Tindie.

Parameters

ParameterValueDescription
Data rateUp to 400 kHzLimited by used TCA4307 IC
I2C Connector2x 4-pin JST-GHConnected in parallel
Operating and storage temperature-20 - +40°CLimited by case material
Operational input voltage3.6 - 5.4V
Mass~2 gPCB
Dimensions15x25x6(10.5)One-sided connectors (With connector on both sides)
Weather resistanceIP00

Features

  • Input Power status LED indicator
  • Optionally possible to solder pass-through I²C connectors to allow a daisy chain of different sensors
  • Ability to isolate I2C bus segments by disconnecting frozen devices
  • Capability to handle differently the Master and a slave bus sides
  • The extender can perform a device reset in case it seems frozen or unresponsive.
  • READY signal indication of the correct connection of both I2C bus sides.

The two I²C Pixhawk connectors on the bottom and top are connected directly. This feature allows easy nesting with other I²C devices onto existing functional bus cabling.

Top view on I2C bus extender

Bottom view on I2C bus extender

Device Reset

The TCA4307 has a stuck bus recovery feature. It disconnects the slave side if SDAOUT or SCLOUT is low for about 40 ms, then generates up to 16 pulses on SCLOUT to reset the bus. The slave side reconnects only after the issue is resolved.

PCB dimensions

PCB dimensions

The PCB is designed to be mounted in the slit and fixed by screws on the sides. The supposed screw diameter is metric 3mm e.g. DIN 912 M3 Hexagon socket Head Cap Screws.

Documentation

The additional documentation is available on the ThunderFly docs website.

Connection

Due to the device reset capability of TFI2CEXT01 special attention should be dedicated to the proper connection of the module to the UAV. The connector closer to the LEDS should be connected to the Master (e.g. autopilot). The opposite connector at the far side from LEDs should be connected to I²C slaves, e.g. sensors.

Parts

26
QtyValueFootprintReferences
6HOLEMlab_Mechanical:dira_3mmM1, M2, M3, M4, M5, M6
410kResistor_SMD:R_0603_1608MetricR2, R3, R5, R6
4SM04B-GHS-TBConnector_JST:JST_GH_SM04B-GHS-TB_1x04-1MP_P1.25mm_HorizontalJ1, J2, J3, J4
2100nFResistor_SMD:R_0603_1608MetricC2, C4
110uFCapacitor_SMD:C_0805_2012MetricC1
1130RResistor_SMD:R_0603_1608MetricR1
11uFResistor_SMD:R_0603_1608MetricC3
1287RResistor_SMD:R_0603_1608MetricR4
1BZX585-B5V6.115Diode_SMD:D_SOD-523D2
1LED GREENMlab_D:LED_1206_millD1
1LED REDMlab_D:LED_1206_millD3
1LOGOMLAB_LOGA:TF 10x4,7G1
1MIC5504-3.3YM5Package_TO_SOT_SMD:SOT-23-5U1
1TCA4307Package_SO:VSSOP-8_3.0x3.0mm_P0.65mmU2

Similar boards

  • 2 layers30 × 15 mmTFHT01, the printed circuit board in 3D

    TFHT01

    ThunderFly-aerospace/TFHT01

    Airborne Humidity and Temperature sensor for UAVs.

    34 parts10GPL-3.0
  • 2 layers25 × 23 mmTFI2CADT01, the printed circuit board in 3D

    TFI2CADT01

    ThunderFly-aerospace/TFI2CADT01

    I2C address translator module, allows connection of multiple I2C devices with the same address to one bus.

    38 parts10GPL-3.0
  • 2 layers37.5 × 19 mmTFRPM01, the printed circuit board in 3D

    TFRPM01

    ThunderFly-aerospace/TFRPM01

    Revolutions per minute (RPM) meter for UAV, rotors, wheels and engines.

    28 parts9GPL-3.0
  • 2 layers45 × 45 mmTFESC02, the printed circuit board in 3D

    TFESC02

    ThunderFly-aerospace/TFESC02

    ESC for BLDC motors for UAVs with I2C interface

    75 parts3GPL-3.0
  • 2 layers25 × 15 mmTFI2CADC01, the printed circuit board in 3D

    TFI2CADC01

    ThunderFly-aerospace/TFI2CADC01

    I2C Analog to digital converter for PixHawk

    20 parts1GPL-3.0
  • 2 layers50 × 50 mmTFGPSLITE02, the printed circuit board in 3D

    TFGPSLITE02

    ThunderFly-aerospace/TFGPSLITE02

    Compact GNSS Module for Lightweight UAVs

    27 partsGPL-3.0
  • 2 layers30 × 15 mmTFASPDIMU02, the printed circuit board in 3D

    TFASPDIMU02

    ThunderFly-aerospace/TFASPDIMU02

    I²C bus differential pressure sensor with IMU and Magnetometer.

    43 parts3GPL-3.0
  • 2 layers70.6 × 50.3 mmTFUNIPAYLOAD01, the printed circuit board in 3D

    TFUNIPAYLOAD01

    ThunderFly-aerospace/TFUNIPAYLOAD01

    Universal interface for TF-ATMON sensor payload.

    81 parts1GPL-3.0

Questions

How big is the TFI2CEXT01 PCB?

It measures 25 × 15 mm and has 2 copper layers, 1.6 mm thick.

What parts does the TFI2CEXT01 use?

26 parts, built around the MIC5504-3.3YM5, TCA4307DGK, SM04B-GHS-TB and BZX585-B5V6,115-JSM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the TFI2CEXT01 KiCad files?

From the ThunderFly-aerospace/TFI2CEXT01 repository on GitHub, at the commit this page was made from: the board is hw/sch_pcb/TFI2CEXT01.kicad_pcb and its schematic hw/sch_pcb/TFI2CEXT01.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the TFI2CEXT01 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).