Skip to the content
2 layers65 × 45 mmWaveRig, the printed circuit board in 3D

WaveRig is an ESP32-S3 BLE bridge connecting ICOM CI-V and Yaesu/Kenwood CAT radios to Wavelog Mobile — reads live frequency, mode and power over Bluetooth and streams it straight into your QSO log. USB-C rechargeable, OLED display, open hardware.

Size
65 × 45 mm
Copper layers
2
Thickness
1.6 mm
Parts
56
Nets
104
Pads
298
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 10.0 (file 20260206)
Created
13 Sep 2026
Updated
26 Sep 2026

Overview

WaveRig is an open-source printed circuit board by TA4RX-SP9AQG, from the TA4RX-SP9AQG/WaveRig repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 65 × 45 mm with 56 parts on 104 nets.

It is built around the ESP32-S3-WROOM-1-N16R8, MAX3232EESE+T and MT3608, with the AP2112K-3.3, DW01A and MAX3421EETJ+ among its other parts. Its parts include 20 capacitors, 15 resistors, 7 ICs, 4 connectors and 2 diodes. It belongs with the radio and wireless and lEDs and displays boards and the ESP32 boards of this library.

Main components

11

README

README.md

WaveRig

An open-hardware ESP32-S3 BLE bridge between amateur radio transceivers and Wavelog Mobile / Wavelog.

WaveRig connects to your radio's CI-V (ICOM) or CAT (Yaesu/Kenwood) interface, reads live frequency, mode and power, and streams it over Bluetooth Low Energy straight into your QSO log — no more typing frequency and mode by hand for every contact.


Status: Early hardware development

  • 🔧 Schematic in progress
  • ⬜ PCB layout not started yet (65×45 mm, 2-layer target)
  • ⬜ Firmware not started yet
  • ⬜ No boards fabricated/tested yet

This repository will track schematic/PCB sources, the bill of materials, and firmware once development begins. Contributions, feedback and testing help are welcome even at this stage.


Planned Features

  • CI-V support — ICOM radios (IC-7300, IC-705, IC-9700, IC-7610, and others) via a 3.5mm jack
  • CAT support — Yaesu / Kenwood radios (FT-891, FT-991A, FT-DX10, TS-590, TS-890, and others) via RS-232 (DB9) through a MAX202 level shifter
  • BLE GATT service — frequency, mode, submode, TX power and rig model pushed live to any connected app
  • Rechargeable — LiPo battery with USB-C charging (TC4056A) and protection (DW01A + FS8205A)
  • USB-C native flashing — no external USB-serial adapter needed; flash directly over the same USB-C port
  • OLED status display — shows frequency, mode and connection status at a glance
  • BLE OTA firmware updates — update via the companion phone app, no cable required (planned)

Hardware Overview

MCUESP32-S3-WROOM-1 (N16R8, 16MB flash)
PowerLiPo 3.7V, USB-C charging, boost to 3.3V (MT3608)
CI-V3.5mm jack, open-drain driver (2N7000)
CAT / RS-232DB9, MAX202EESE+T level shifter
DisplayI2C OLED (SSD1306, 4-pin connector)
PCB65×45mm, 2-layer

Schematic and PCB design are being developed by Süalp, TA4HCK. Full BOM, pin assignments and net-by-net connection notes will be published in this repo as the hardware design is finalized.

Firmware Roadmap

  1. BLE GATT service (frequency / mode / submode / power / rig model, notify-based)
  2. CI-V protocol parsing (ICOM)
  3. CAT protocol parsing (Yaesu / Kenwood)
  4. OLED UI
  5. BLE OTA updates (phone acts as the bridge to the internet — no Wi-Fi needed on-device)

Related Projects

  • Wavelog Mobile — the Android companion app WaveRig connects to
  • Wavelog — the self-hosted amateur radio logging server

Contributing

This project is in early hardware development — schematic and PCB files, along with contribution guidelines, will be added as the design stabilizes. Issues and discussion are welcome in the meantime.

License

Licensed under the Apache License 2.0.


By Erkin, TA4RX / SP9AQG (firmware / software) and Süalp, TA4HCK (schematic / PCB)

Parts

56
QtyValueFootprintReferences
8100nFCapacitor_SMD:C_0603_1608MetricC2, C4, C5, C6, C7, C8, C22, C26
55.1kResistor_SMD:R_0603_1608MetricR6, R7, R8, R9, R10
410uFCapacitor_SMD:C_0805_2012MetricC24, C25, C27, C28
31uFCapacitor_SMD:C_0603_1608MetricC21, C23, C29
210kResistor_SMD:R_0603_1608MetricR4, R5
222pFCapacitor_SMD:C_0603_1608MetricC19, C20
233R 1%Resistor_SMD:R_0603_1608MetricR15, R16
11.2kResistor_SMD:R_0603_1608MetricR1
1100RResistor_SMD:R_0603_1608MetricR17
1100k 1%Resistor_SMD:R_0603_1608MetricR12
1100uFCapacitor_SMD:C_1206_3216MetricC18
110uFCapacitor_SMD:C_0603_1608MetricC3
112MHz CL18pF ESR60R maxCrystal:Crystal_SMD_HC49-SDY1
11kResistor_SMD:R_0603_1608MetricR18
122uFCapacitor_SMD:C_0805_2012MetricC1
12N7000Package_TO_SOT_THT:TO-92_InlineQ1
14.7kResistor_SMD:R_0603_1608MetricR19
14.7uHInductor_SMD:L_6.3x6.3_H3L2
1732k 1%Resistor_SMD:R_0603_1608MetricR11
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U3
1BOOTButton_Switch_SMD:SW_SPST_B3S-1000SW2
1CIV_3.5mm_TRS_JackConnector_Audio:Jack_3.5mm_CUI_SJ1-3523N_HorizontalJ1
1DW01APackage_TO_SOT_SMD:SOT-23-6U2
1ESP32-S3-WROOM-1-N16R8RF_Module:ESP32-S3-WROOM-1U6
1FS8205APackage_SO:TSSOP-8_4.4x3mm_P0.65mmQ2
1LD09S24A4GV00LFConnector_Dsub:DSUB-9_Socket_Horizontal_P2.77x2.54mm_EdgePinOffset9.40mmDSUB1
1LiPo_3.7V_JST-PHConnector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_VerticalBT1
1MAX3232EESE+TPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU4
1MAX3421EETJ+Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.7x3.7mmU7
1MT3608Package_TO_SOT_SMD:SOT-23-6U9
1OLED_SSD1306_I2CConnector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_VerticalCN1
1RESETButton_Switch_SMD:SW_SPST_B3S-1000SW1
1SMBJ5.0CADiode_SMD:D_SMBD4
1SS34Diode_SMD:D_SMAD3
1TC4056APackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU1
1USB-A_HostConnector_USB:USB_A_Receptacle_GCT_USB1046J3
1USB-C_16P-F-SMTConnector_USB:USB_C_Receptacle_GCT_USB4115-03-CJ2

Similar boards

  • 2 layers65 × 38.2 mmGps tracer, the printed circuit board in 3D

    Gps tracer

    OlegDemk/ESP32_GPS_loger_v1

    GPS logger can log in GPS data every 5 seconds into Micro SD card.

    88 parts
  • 2 layers62 × 6 mmTableLight, the printed circuit board in 3D

    TableLight

    jonny190/TableLight

    A 3D-printable, battery-powered, USB-C rechargeable table lamp in the classic "Poldina" shape - honeycomb disc base, thin stem, down-firing cone shade with a white top - running WLED on an ESP32, with a capacitive touch…

    72 partsMIT
  • 2 layers100 × 100.1 mmDiploma, the printed circuit board in 3D

    Diploma

    t3ry4git/stm32Co2

    A simple CO2 and environmental monitor based on the STM32F103C8 microcontroller. The firmware reads temperature and humidity from a DHT22 sensor, measures CO2 concentration using an MHZ19B module and displays values on…

    62 parts
  • 2 layers76.2 × 50.8 mmPowerCircuit, the printed circuit board in 3D

    PowerCircuit

    usandakahle/DesignProject

    Kicad, schematics EEE3088F

    63 parts
  • 2 layers20.1 × 62.5 mmESP USB, the printed circuit board in 3D

    ESP USB

    Lumethra/ESP-USB

    40 parts
  • 2 layers192.4 × 50 mmOmote, the printed circuit board in 3D

    Omote

    OMOTE-Community/OMOTE-Hardware

    Open Source Remote - Hardware

    187 parts157GPL-3.0
  • 2 layers61 × 61 mmESP32 FC, the printed circuit board in 3D

    ESP32 FC

    MAATHES-THILAK-K/ESP32-S3_FLIGHT_CONTROLLER

    A custom-designed flight controller based on the ESP32-S3 module, built for compatibility with the esp-fc firmware and Betaflight-like configuration.

    69 parts7Apache-2.0
  • 2 layers80 × 34 mmDji fcc, the printed circuit board in 3D

    Dji fcc

    nikolaus018/dji-fcc-esp32

    ESP32-S3 firmware that switches a DJI N1 remote to FCC mode over USB (replaces the Android app)

    69 parts3MIT

Questions

How big is the WaveRig PCB?

It measures 65 × 45 mm and has 2 copper layers, 1.6 mm thick.

What parts does the WaveRig use?

56 parts, built around the ESP32-S3-WROOM-1-N16R8, MAX3232EESE+T, MT3608 and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WaveRig KiCad files?

From the TA4RX-SP9AQG/WaveRig repository on GitHub, at the commit this page was made from: the board is hardware/kicad/WaveRig.kicad_pcb and its schematic hardware/kicad/WaveRig.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the WaveRig design in my own project?

Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).