

ARDUINO MEGA. SOLOMON
The Custom Arduino Mega is an open-source hardware project developed as a custom implementation of the Arduino Mega platform.
- Size
- 101.6 × 53.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 69
- Nets
- 216
- Pads
- 402
- Tracks, vias
- 418, 10
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 13 Aug 2026
- Updated
- 13 Aug 2026
Overview
ARDUINO MEGA. SOLOMON is an open-source printed circuit board by Solomon-Menney, from the Solomon-Menney/ARDUINO-MEGA repository on GitHub. It is a 2-layer board of 101.6 × 53.3 mm with 69 parts on 216 nets, routed with 418 tracks and 10 vias.
It is built around the ATMEGA16U2-MU, ATMEGA2560-16AU and LM358D, with the LP2985-33DBV and FDN340P among its other parts. Its parts include 17 capacitors, 7 connectors, 6 ICs, 4 resistors and 4 crystals. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5ATMEGA16U2-MU
QFN-32-EP(5x5)-40℃~+85℃ 16KB 16MHz 2.7V~5.5V 22 512Byte 512Byte 8 Bit AVR Built-in FLASH QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)ATMEGA2560-16AU
TQFP-100(14x14)-40℃~+85℃ 10bit 16MHz 256KB 4.5V~5.5V 4KB 8 Bit 86 8KB AVR Built-in FLASH TQFP-100(14x14) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM358D
SOIC-8-16V~16V 0℃~+70℃ 2 3V~32V 40mA 45nA 5nA 700uA 70dB 7mV 7uV/℃ Built-in compensation、ESD protection SOIC-8 Operational Amplifier ROHSonsemiOperational AmplifierLP2985-33DBV
SOT-23-5-40℃~+125℃@(Tj) 1 150mA 16V 3.3V 30uVrms 45dB@(1kHz) 575mV@(150mA) 850uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsFDN340P
SOT-23-55℃~+150℃ 1 P-Channel 1.5V 121pF 20V 2A 500mW 56pF 7.2nC@4.5V 70mΩ@4.5V 779pF P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
README
README.md📌 Project Overview
The Custom Arduino Mega is an open-source hardware project developed as a custom implementation of the Arduino Mega platform.
The board is suitable for:
- Embedded systems development
- Robotics projects
- Automation and control systems
- IoT applications
- Sensor interfacing
- Motor control
- Electronics prototyping
- Academic and engineering projects
✨ Features
- ATmega2560 microcontroller
- Arduino Mega-compatible architecture
- Digital I/O pins
- Analog input pins
- PWM outputs
- UART serial communication
- SPI communication
- I²C communication
- USB programming/communication interface
- External power input
- On-board voltage regulation
- Reset circuit
- ICSP programming interface
- Power and status indicators
- Standard Arduino-style headers
🔧 Main Specifications
| Parameter | Specification |
|---|---|
| Microcontroller | ATmega2560 |
| Architecture | 8-bit AVR |
| Operating Voltage | 5 V |
| Digital I/O | 54 |
| PWM Outputs | 15 |
| Analog Inputs | 16 |
| UART Ports | 4 |
| Communication | UART, SPI, I²C |
| Clock Frequency | 16 MHz |
| Programming | USB / ICSP |
| PCB Design Software | KiCad |
| Board Type | Custom PCB |
🧠 Microcontroller
The main controller used on the board is the ATmega2560.
The microcontroller provides a large number of digital and analog I/O pins, making the board suitable for projects that require more pins than a standard Arduino Uno.
ATmega2560 Functions
- Digital input/output
- Analog-to-digital conversion
- PWM generation
- Hardware timers
- UART communication
- SPI communication
- I²C communication
- External interrupts
- Flash, SRAM and EEPROM memory
🔌 Communication Interfaces
The board supports several communication protocols.
UART
The ATmega2560 provides four hardware serial interfaces:
- Serial0
- Serial1
- Serial2
- Serial3
These can be used to communicate with:
- GPS modules
- GSM modules
- Bluetooth modules
- Other microcontrollers
- Computers
I²C
I²C can be used to connect devices such as:
- Sensors
- LCD displays
- RTC modules
- EEPROMs
- I/O expanders
SPI
SPI can be used for high-speed communication with:
- SD cards
- Displays
- Sensors
- Flash memory
- Other SPI devices
⚡ Power Supply
The board contains a dedicated power section for supplying the required voltage to the microcontroller and other circuits.
Possible power sources include:
- USB
- External DC input
The power section includes:
- Voltage regulation
- Power filtering
- Decoupling capacitors
- Reverse-polarity protection (if implemented)
- Power indicator LED
Note: Verify the exact input-voltage range of your implemented power circuit before connecting an external supply.
🔄 Reset Circuit
A reset circuit is included to allow the ATmega2560 to restart and enter the bootloader/programming process.
The reset circuit consists of components such as:
- Reset push button
- Pull-up resistor
- Reset capacitor (depending on the design)
💻 Programming
The board can be programmed using the Arduino IDE or another compatible AVR development environment.
Arduino IDE
- Install the Arduino IDE.
- Connect the board to a computer through USB.
- Select the appropriate board configuration.
- Select the correct COM port.
- Upload your Arduino program.
For a Mega-compatible configuration, select:
Tools → Board → Arduino Mega or Mega 2560
Then select the appropriate processor option for your hardware.
🖥️ PCB Design
The PCB was designed using KiCad.
The project includes the following design files:
Custom-Arduino-Mega/
│
├── README.md
│
├── Schematic/
│ └── Arduino_Mega.kicad_sch
│
├── PCB/
│ └── Arduino_Mega.kicad_pcb
│
├── Gerber/
│ └── Manufacturing_Files/
│
├── 3D/
│ └── PCB_3D_View/
│
└── Documentation/
├── Pinout/
└── Images/📐 Design Files
The repository contains:
- KiCad schematic
- KiCad PCB layout
- Gerber files
- Drill files
- Bill of Materials (BOM)
- Component datasheets
- Firmware/test programs
- PCB renders
- Project documentation
🧾 Bill of Materials
| Component | Description | Quantity |
|---|---|---|
| ATmega2560 | Main microcontroller | 1 |
| USB Interface | USB communication/programming | 1 |
| Voltage Regulator | 5 V regulation | 1 |
| Crystal/Oscillator | 16 MHz clock | 1 |
| Capacitors | Power/decoupling | Several |
| Resistors | Pull-up/current limiting | Several |
| LEDs | Power/status indicators | Several |
| Push Button | Reset | 1 |
| Pin Headers | I/O connections | Several |
| Diodes | Protection | As required |
The exact component values and part numbers are provided in the project schematic and BOM.
📷 Project Images
Add your project images here.
Schematic

PCB Layout

3D PCB View

This custom Arduino Mega board can be used in:
- Industrial automation
- Robotics
- Smart home systems
- IoT systems
- Solar energy systems
- Motor control
- Sensor networks
- Data acquisition
- Embedded control systems
- Engineering research and education
🛠️ Tools Used
Hardware Design
- KiCad
- ATmega2560 datasheet
- AVR documentation
Software
- Arduino IDE
- AVR toolchain
Manufacturing
- PCB fabrication service
- Soldering and assembly tools
Documentation
Important documents are included in the Documentation directory.
These may include:
- Circuit schematic
- PCB layout
- Pinout diagram
- Datasheets
- BOM
- Design calculations
- Assembly information
- Testing results
Recommended Tests
- Visual inspection
- Check for PCB shorts
- Verify power input
- Verify regulated voltage
- Test reset circuit
- Test USB communication
- Test microcontroller programming
- Test digital I/O
- Test analog inputs
- Test UART
- Test I²C
- Test SPI
📈 Future Improvements
Possible future improvements include:
- Improved power protection
- USB-C connector
- Additional power monitoring
- Battery input
- Reverse-polarity protection
- ESD protection
- Improved PCB layout
- Additional status indicators
- More expansion connectors
- Improved thermal management
Author SOLOMON MENNEY Electrical/Electronic Engineering Student Accra Technical University
Built with KiCad, AVR technology, and a passion for embedded systems.
Parts
69| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4, C5, C6, C7, C8, C9, C11, C12, C13 |
| 6 | MountingHole_3.2mm | Arduino_MountingHole:MountingHole_3.2mm | MH1, MH2, MH3, MH4, MH5, MH6 |
| 5 | 22p | Capacitor_SMD:C_0805_2012Metric | C1, C14, C15, C16, C17 |
| 3 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | GROUND1, RESET-EN1, UBOOT1 |
| 2 | 10K | Resistor_SMD:R_Array_Convex_4x0603 | RN1, RN5 |
| 2 | 16MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Q2, Q3 |
| 2 | 1K | Resistor_SMD:R_Array_Convex_4x0603 | RN3, RN4 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 27R | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 2 | 47u | Capacitor_SMD:CP_Elec_6.3x5.4 | PC1, PC2 |
| 2 | Analog | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J3, J5 |
| 2 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | ICSP1, ICSP2 |
| 2 | MC33269ST-5.0T3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | IC1, IC2 |
| 2 | PGB1010604 | Resistor_SMD:R_0603_1608Metric | Z1, Z2 |
| 1 | 16MHz | Crystal:Resonator_SMD_Murata_CSTxExxV-3Pin_3.0x1.1mm | Y2 |
| 1 | 16MHz | Crystal:Crystal_SMD_HC49-SD | Y1 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 22R | Resistor_SMD:R_Array_Convex_4x0603 | RN2 |
| 1 | 500mA | Fuse:Fuse_1812_4532Metric | F1 |
| 1 | ATmega16U2-M | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | IC4 |
| 1 | ATmega2560-16A | Package_QFP:TQFP-100_14x14mm_P0.5mm | IC3 |
| 1 | BLM21 | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Horizontal | X1 |
| 1 | Communication | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J6 |
| 1 | Digital | Connector_PinSocket_2.54mm:PinSocket_2x18_P2.54mm_Vertical | J7 |
| 1 | FDN340P | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | L | LED_SMD:LED_0805_2012Metric | YELLOW1 |
| 1 | LM358D | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | IC5 |
| 1 | LP2985-3.3 | Package_TO_SOT_SMD:SOT-23-5 | IC6 |
| 1 | M7 | Diode_SMD:D_SMA | D1 |
| 1 | ON | LED_SMD:LED_0805_2012Metric | GREEN1 |
| 1 | PWM | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J2 |
| 1 | PWM | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J4 |
| 1 | Power | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | RX | LED_SMD:LED_0805_2012Metric | YELLOW2 |
| 1 | TS42 | Button_Switch_SMD:SW_SPST_PTS645Sx43SMTR92 | RESET1 |
| 1 | TX | LED_SMD:LED_0805_2012Metric | YELLOW3 |
| 1 | USB_B | Connector_USB:USB_B_OST_USB-B1HSxx_Horizontal | X2 |
Similar boards
- 2 layers101.6 × 53.3 mm

- 2 layers101.6 × 53.3 mm

- 2 layers101.6 × 53.3 mm

- 2 layers101.6 × 53.3 mm

- 2 layers68.6 × 53.3 mm

Arduino Mega 2560
ded811/Mega-Uno-2560
An Arduino-compatible ATmega2560 development board in the Arduino Uno form factor
62 parts1 - 2 layers76 × 56 mm

- 2 layers67.8 × 56 mm

Arduino
aarthirethinabala/Arduino-Uno-Compatible-PCB
Custom Arduino Uno-compatible PCB designed in KiCad, including schematic, PCB layout, routing, and 3D visualization.
56 parts - 4 layers68.9 × 50.7 mm

DigitalClock ATMega328
bostang/PCBs
My repository for documenting all PCB Projects I have done
74 parts
Questions
How big is the ARDUINO MEGA. SOLOMON PCB?
It measures 101.6 × 53.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ARDUINO MEGA. SOLOMON use?
69 parts, built around the ATMEGA16U2-MU, ATMEGA2560-16AU, LM358D and LP2985-33DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ARDUINO MEGA. SOLOMON KiCad files?
From the Solomon-Menney/ARDUINO-MEGA repository on GitHub, at the commit this page was made from: the board is ARDUINO MEGA. SOLOMON.kicad_pcb and its schematic ARDUINO MEGA. SOLOMON.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ARDUINO MEGA. SOLOMON design in my own project?
Its repository states no licence, so its author keeps all rights: ask Solomon-Menney before reusing the design.