2 layers107 × 62 mm
2 layers54 × 76.8 mm
Dimmer y consumo
ProyectosMicroPIC/Gestor-de-Excedentes1Gestor de Excedentes MicroPIC
- Size
- 54 × 76.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 59
- Pads
- 178
- Tracks, vias
- 357, 15
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 23 Feb 2024
- Updated
- 25 Feb 2024
Overview
Dimmer y consumo is an open-source printed circuit board by ProyectosMicroPIC, from the ProyectosMicroPIC/Gestor-de-Excedentes repository on GitHub. It is a 2-layer board of 54 × 76.8 mm with 46 parts on 59 nets, routed with 357 tracks and 15 vias.
It is built around the ESP32-C3-MINI-1, BTA16-600B and LM1117DT-3.3, with the MOC3021M, B500R and BC807 among its other parts. Its parts include 12 resistors, 9 capacitors, 5 ICs, 5 connectors and 3 transistors. It belongs with the ESP32 and RISC-V boards of this library.
Main components
7ESP32-C3-MINI-1
--40℃~+81℃ -89dBm 2.4GHz 350mA 3V~3.6V 82mA ESP32-C3 Chip On-board PCB Antenna UART - WiFi Modules ROHSRF CrazyWiFi Modules
BTA16-600B
TO-220A-40℃~+125℃ 1 TRIAC 1.5V 160A@20ms 16A 1V 500mW 50mA 600V 60mA TO-220A Thyristors (SCR)/Modules ROHSKTPThyristors (SCR)/Modules
LM1117DT-3.3
TO-2520℃~+125℃@(Tj) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MOC3021M
DIP-6-40℃~+85℃ 0.1mA 1 1.15V 100mA 330mW 4.17kV 400V 6 60mA No TRIAC DIP-6 Triac, SCR Output Optoisolators ROHSonsemiTriac, SCR Output Optoisolators
B500R
DIP-4-50℃~+150℃@(Tj) 1V@1A 1kV 2A 50A 5uA@1kV Single-Phase Rectifier DIP-4 Bridge Rectifiers ROHSDIOTECBridge Rectifiers
BC807
SOT-23-65℃~+150℃ 1 PNP 100 100nA 345mW 45V 500mA 5V 700mV 80MHz PNP SOT-23 Bipolar (BJT) ROHSNexperiaBipolar (BJT)BC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
README
README.mdCon este Gestor de Excedentes completamente DIY podrás derivar tus excedentes fotovoltaicos a cualquier electrodoméstico (resistivo) que tengas en casa, aprovechando la energía sobrante de la mejor manera.
En el vídeo te explico cómo está hecho y cómo funciona.
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10K | Resistor_SMD:R_0805_2012Metric | R6, R9, R10, R11, R12 |
| 4 | 100nF | Resistor_SMD:R_0805_2012Metric | C2, C4, C5, C9 |
| 2 | 0 | Resistor_SMD:R_0805_2012Metric | R7, R8 |
| 2 | 100uF | Capacitor_SMD:C_Elec_6.3x7.7 | C1, C3 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric | R4, R5 |
| 2 | 30K 1/2W | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R3 |
| 1 | 10nF | Resistor_SMD:R_0805_2012Metric | C7 |
| 1 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 1nF | Resistor_SMD:R_0805_2012Metric | C8 |
| 1 | 1uF | Capacitor_SMD:C_Elec_6.3x7.7 | C6 |
| 1 | 220Vac | Connector_Phoenix_MSTB:PhoenixContact_MSTBVA_2,5_2-G-5,08_1x02_P5.08mm_Vertical | J1 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D2.5mm | 3V3 |
| 1 | 5V | Connector_Phoenix_MSTB:PhoenixContact_MSTBVA_2,5_2-G-5,08_1x02_P5.08mm_Vertical | J3 |
| 1 | ACS724LLCTR-10AB-S | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | ADS1115_ADC_Module | Charleslab:ADC1115_ADC_Module | A1 |
| 1 | Analógicas | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J5 |
| 1 | B500R | Diode_THT:Diode_Bridge_Round_D9.0mm | D1 |
| 1 | BC807 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | BC817 | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | BTA16-600B | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | CHIP_PU | TestPoint:TestPoint_Pad_D2.5mm | RST |
| 1 | Cruce0 | TestPoint:TestPoint_Pad_D2.5mm | Z0 |
| 1 | ESP32-C3-MINI-1 | PCM_Espressif:ESP32-C3-MINI-1 | U4 |
| 1 | GND | TestPoint:TestPoint_Pad_D2.5mm | GND |
| 1 | GPIO9 | TestPoint:TestPoint_Pad_D2.5mm | TP5 |
| 1 | Heatsink | Heatsink:Heatsink_Fischer_SK104-STCB_35x13mm__2xDrill3.5mm_ScrewM3 | HS1 |
| 1 | LM1117DT-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | MOC3021M | Package_DIP:DIP-6_W7.62mm | U3 |
| 1 | PC817 | Package_DIP:DIP-4_W7.62mm | U2 |
| 1 | Programación | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | SCL | TestPoint:TestPoint_Pad_D2.5mm | SCL |
| 1 | SDA | TestPoint:TestPoint_Pad_D2.5mm | SDA |
| 1 | Salida | Connector_Phoenix_MSTB:PhoenixContact_MSTBVA_2,5_2-G-5,08_1x02_P5.08mm_Vertical | J2 |
| 1 | Test1 | TestPoint:TestPoint_Pad_D2.5mm | TEST |
| 1 | Triac | TestPoint:TestPoint_Pad_D2.5mm | TP6 |
Similar boards
- 2 layers64.3 × 63 mm
Triac AC Dimmer 1P
Eninspace/triac
This project is based on esp8266 and TRIAC for control power via remote control.
28 parts5GPL-3.0 - 2 layers100 × 60 mm
Hotplate soldering
Arnaud-Apu-Fanovard/Hotplate-soldering
Hotplate soldering for PCB SMD componants for diyPCB
46 parts - 2 layers117 × 62 mm
- 2 layers100 × 100 mm
- 2 layers30 × 30 mm
- 2 layers99.8 × 60.2 mm
Irrigation IoT
VictorRavani/Irrigation_IoT
This project covers the complete development of Hardware and Firmware for IoT-based supervisory control. It offers all the necessary information and resources so that anyone can set up the system independently.
79 parts4MIT - 4 layers100 × 80 mm
ESP32
Tanmayeers/Projects
Specifications: 1. Operting Voltage: 9V 2. Operating Current: 200mA 3. Output Voltage Swing: 6.5V 4. 3dB - Bandwidth: 100 ± 10 Hz 5. Noise: 5.406mVrms
63 parts1
Questions
How big is the Dimmer y consumo PCB?
It measures 54 × 76.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dimmer y consumo use?
46 parts, built around the ESP32-C3-MINI-1, BTA16-600B, LM1117DT-3.3 and MOC3021M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dimmer y consumo KiCad files?
From the ProyectosMicroPIC/Gestor-de-Excedentes repository on GitHub, at the commit this page was made from: the board is Circuito/Dimmer y consumo.kicad_pcb and its schematic Circuito/Dimmer y consumo.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dimmer y consumo design in my own project?
Its repository states no licence, so its author keeps all rights: ask ProyectosMicroPIC before reusing the design.