
Mbus master
roarfred/AmsToMqttBridge
Minimalistic system to read AMS/HAN data from electrical meter

Hardware design for the Spotlight setup
Triggering electronics v3 is an open-source printed circuit board by NeLy-EPFL, from the NeLy-EPFL/spotlight-hardware repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 56.6 × 70.9 mm with 27 parts on 48 nets, routed with 190 tracks and 1 via.
It is built around the BC337. Its parts include 9 connectors, 7 resistors, 4 diodes, 4 transistors and 1 capacitor. It belongs with the ESP32 and AVR (ATmega, ATtiny) boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2, R3, R4, R6, R7, R8 |
| 6 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-2-2.54_1x02_P2.54mm_Horizontal | J1, J2, J3, J4, J5, J6 |
| 4 | BC337 | Package_TO_SOT_THT:TO-92L_Wide | Q1, Q2, Q3, Q4 |
| 3 | D_Zener | Diode_THT:D_DO-15_P12.70mm_Horizontal | D2, D3, D4 |
| 2 | Conn_01x04_Pin | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J8, J9 |
| 1 | Arduino_Nano_ESP32 | Module:Arduino_Nano | A1 |
| 1 | C_Polarized | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1 |
| 1 | Conn_02x05_Odd_Even | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J7 |
| 1 | LED_BRKG | LED_THT:LED_D5.0mm-4_RGB_Staggered_Pins | D1 |
| 1 | Polyfuse | Fuse:Fuse_Littelfuse_395Series | F1 |

roarfred/AmsToMqttBridge
Minimalistic system to read AMS/HAN data from electrical meter



leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO

pablozg/freeds
Derivador de energía solar excedente creado por Pablo Zerón, Diseño PCB por Amcalo, Tester original por Aeizoon, Wiki por Zoilo Mora

lampmerchant/tashtwenty
An interface for the DCD protocol used by Apple's Hard Disk 20.

CTXz/Video-Glitch-Array
A collection of glitch art circuits dedicated to VGA signal manipulation

It measures 56.6 × 70.9 mm and has 2 copper layers, 1.6 mm thick.
27 parts, built around the BC337. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the NeLy-EPFL/spotlight-hardware repository on GitHub, at the commit this page was made from: the board is trigger_controller/circuit_design/triggering_electronics_v3/triggering_electronics_v3.kicad_pcb and its schematic trigger_controller/circuit_design/triggering_electronics_v3/triggering_electronics_v3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).