Skip to the content
2 layers10 × 22 mm5v buck pt iii, the printed circuit board in 3D

This repository is meant to have all of the research relating to power systems for the vehicle.

Size
10 × 22 mm
Copper layers
2
Thickness
1.6 mm
Parts
10
Nets
7
Pads
24
Tracks, vias
18, 5
Pours
4
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
30 Sep 2023
Updated
19 Apr 2025

Overview

5v buck pt iii is an open-source printed circuit board by NJIT-Highlander-Racing-Electrical, from the NJIT-Highlander-Racing-Electrical/Power repository on GitHub. It is a 2-layer board of 10 × 22 mm with 10 parts on 7 nets, routed with 18 tracks and 5 vias.

It is built around the AP62301WU. Its parts include 4 capacitors, 2 resistors, 2 connectors, 1 IC and 1 inductor. It belongs with the power boards of this library.

Main components

1

README

README.md

Power

A repository dedicated to everything power-related: batteries, connectors, wiring, battery management, systems, and more.

Batteries

  • Zippy 5000mAh 11.1v batteries
    • Can be ran in parallel after balancing for extra capacity
    • Housed in a 3D printed dual battery holder
    • Two thumb screws lock the batteries into place with a cover bar
  • Battery Management System
    • Uses a Low Voltage Disconnect Module to cut off battery power when battery voltage gets too low
    • Ideally includes short circuit protection or fuse

Wiring

  • 14 AWG wire for main power bus connections
  • 24 AWG wire to split off to smaller subsystems
  • CAN-Bus signals are sent over 24 AWG twisted pair wire
  • All subsystems use 4-pin Aviation Plug Connectors for 12V power and CAN-Bus signals

Voltage Regulation at Subsystems

  • All subsystems will have a 5V switching regulators
    • Running the vehicle power bus at 12V but each subsystem only requiring 5V allows for a voltage drop on the bus without issues
    • Switching regulators are far more efficient than linear regulators, which would get too hot stepping down from 12V to 5V at higher loads
    • The ESP32 can also output 3.3V from the 5V we supply if needed for its subsystems

Parts

10
QtyValueFootprintReferences
222uCapacitor_SMD:C_0603_1608MetricC2, C4
2Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1, J2
1100nCapacitor_SMD:C_0402_1005MetricC3
110kResistor_SMD:R_0402_1005MetricR2
110uCapacitor_SMD:C_0603_1608MetricC1
13.3uInductor_SMD:L_Taiyo-Yuden_NR-50xxL1
152.3kResistor_SMD:R_0402_1005MetricR1
1AP62301WUPackage_TO_SOT_SMD:TSOT-23-6U1

More from NJIT-Highlander-Racing-Electrical/Power

2
  • 2 layers5v Buck Pt ii, the printed circuit board in 3D

    5v Buck Pt ii

    NJIT-Highlander-Racing-Electrical/Power

    This repository is meant to have all of the research relating to power systems for the vehicle.

    9 parts
  • 2 layers10 × 22 mmFallback Voltage Regulator PCB, the printed circuit board in 3D

    Fallback Voltage Regulator PCB

    NJIT-Highlander-Racing-Electrical/Power

    This repository is meant to have all of the research relating to power systems for the vehicle.

    3 parts

Similar boards

  • 4 layers355 × 160 mmLiBCM, the printed circuit board in 3D

    LiBCM

    doppelhub/Honda_Insight_LiBCM

    Replacement BCM for G1 Honda Insight Lithium Conversion

    717 parts25CC-BY-SA-4.0
  • 6 layers95.9 × 90.2 mmCpb, the printed circuit board in 3D

    Cpb

    OakwoodEngineering/ObiWanKomputer

    The Obi Wan Komputer and Combined Payload Boards from the NyanSat project.

    251 parts10
  • 2 layers65 × 56 mmTitan 2022, the printed circuit board in 3D

    Titan 2022

    hpvdt/titan_2022

    TITAN Vision System going into WHPSC 2022

    73 parts1
  • 4 layers59 × 71 mmPEC Sensor, the printed circuit board in 3D

    PEC Sensor

    WAFFLE-Systems/PEC_Sensor

    Electrical schematics and PCB gerber files for the Pulsed Eddy Current Sensor

    98 parts1
  • 2 layers99 × 80 mmKit Altera rev0, the printed circuit board in 3D

    Kit Altera rev0

    Jonas-Chaves/Kit_MAX10_FPGA

    Kit didático FPGA baseado no Intel MAX 10

    115 partsMIT
  • 2 layers51.8 × 78.1 mmCVTPCB, the printed circuit board in 3D

    CVTPCB

    NJIT-Highlander-Racing-Electrical/CVT-Tachometer

    A subsystem that measures the RPM of the primary and secondary on the CVT

    46 parts
  • 4 layers126 × 90 mmIncubator controller, the printed circuit board in 3D

    Incubator controller

    tanaes/OvoEasy_incubator_controller

    KiCad design for the OvoEasy incubator controller board

    169 parts
  • 2 layers34.3 × 42.2 mmRs485adapter, the printed circuit board in 3D

    Rs485adapter

    harrydshill/Base-Station

    44 parts

Questions

How big is the 5v buck pt iii PCB?

It measures 10 × 22 mm and has 2 copper layers, 1.6 mm thick.

What parts does the 5v buck pt iii use?

10 parts, built around the AP62301WU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the 5v buck pt iii KiCad files?

From the NJIT-Highlander-Racing-Electrical/Power repository on GitHub, at the commit this page was made from: the board is Custom Voltage Regulator Board/5v buck pt iii.kicad_pcb and its schematic Custom Voltage Regulator Board/5v buck pt iii.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the 5v buck pt iii design in my own project?

Its repository states no licence, so its author keeps all rights: ask NJIT-Highlander-Racing-Electrical before reusing the design.