
Paxtogeddon pcb
en4rab/Paxtogeddon-OLED-PCB
Hardware files for the Paxtogeddon reader with OLED display

DMX controller for two ancient industrial fans
Fan controller pcb is an open-source printed circuit board by LennardBoediger, from the LennardBoediger/dmx-fan-controller repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 100 × 130 mm with 53 parts on 51 nets, routed with 257 tracks and 9 vias.
It is built around the MAX485ED, MCP4922-E/P and TLC272CD, with the MC7805CDTG among its other parts. Its parts include 17 resistors, 7 capacitors, 5 ICs, 3 connectors and 2 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Speed controller for two old industrial fans.
The Fans are powerd by three-phase alternating current and come with an 0-10V control line. The lowest possible speed setting during runtime is 1.6V but 2.6V is required to start the motors from standstill
The controller board is based on the Arduino Nano (ATmega328).
For the Fan Control line a 0-5V 10Bit DAC is used. The output voltage is then amplified, so that we end up with an 0-10V 10Bit DAC.
To communicate over the DMX-Bus, the board is equipped with an MAX485E RS-485 transceiver.
The DMX channel can be selected using a DIP switch.
Additionally there is an manual control override, which allows the fan to be set to a constant speed.
Mounting holes are M3.
Please don't die when using large spinning fan blades that are powered by three-phase current.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 10KR | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R13 |
| 5 | MountingHole | MountingHole:MountingHole_3.2mm_M3_ISO14580_Pad_TopBottom | H1, H2, H3, H4, H5 |
| 4 | 0.33 uF | Capacitor_SMD:C_1812_4532Metric | C1, C2, C3, C4 |
| 3 | 0.1uC | Capacitor_SMD:C_0805_2012Metric | C5, C6, C7 |
| 2 | 1KR | Resistor_SMD:R_0603_1608Metric | R15, R17 |
| 2 | 2KR | Resistor_SMD:R_0603_1608Metric | R11, R12 |
| 1 | 120R | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 220R | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | Arduino_Nano_Every | Module:Arduino_Nano | A1 |
| 1 | G*** | kibuzzard-640DCC82 | kibuzzard-640DCC82 |
| 1 | G*** | kibuzzard-640DCC72 | kibuzzard-640DCC72 |
| 1 | G*** | kibuzzard-640DCC79 | kibuzzard-640DCC79 |
| 1 | G*** | kibuzzard-640DCC4D | kibuzzard-640DCC4D |
| 1 | G*** | kibuzzard-640DCC52 | kibuzzard-640DCC52 |
| 1 | G*** | kibuzzard-63FA74BB | kibuzzard-63FA74BB |
| 1 | G*** | kibuzzard-640DCC6D | kibuzzard-640DCC6D |
| 1 | G*** | kibuzzard-63FA7528 | kibuzzard-63FA7528 |
| 1 | G*** | kibuzzard-63FA74F3 | kibuzzard-63FA74F3 |
| 1 | G*** | kibuzzard-63FA74A1 | kibuzzard-63FA74A1 |
| 1 | G*** | kibuzzard-640DCC68 | kibuzzard-640DCC68 |
| 1 | Linear_10KR_Potentiometer | Potentiometer_THT:Potentiometer_Vishay_148-149_Single_Horizontal | RV1 |
| 1 | MAX485E | RS-485_Tranceivers:MAX485E | U5 |
| 1 | MC7805CDTG | Voltage_Regulator:MC785BDTG | U2 |
| 1 | MC7812BDTG | Voltage_Regulator:MC7812BDTG | U1 |
| 1 | MCP4922 | DAC:MCP4912 | U3 |
| 1 | Red_Heatbeat_LED | LED_THT:LED_D3.0mm_Horizontal_O1.27mm_Z6.0mm | D1 |
| 1 | SW_DIP_x10 | DIP_Switch:WS-DITU_Compact_THT_Right_Angled | SW2 |
| 1 | SW_SPDT | Switch:WS-TOTV_6.35_Right_Angle_Toggle_Switch | SW1 |
| 1 | Screw_Terminal_01x04 | TerminalBlock:TerminalBlock_Altech_AK300-4_P5.00mm | J1 |
| 1 | TLC272 | OpAmp:tlc272a | U4 |
| 1 | nc3fdm3-v | XLR_Connector:nc3fdm3-h | J2 |
| 1 | nc3mdm3-v | XLR_Connector:nc3mdm3-h | J3 |

en4rab/Paxtogeddon-OLED-PCB
Hardware files for the Paxtogeddon reader with OLED display





CASE-Association/christmas-cards
All CASE christmas cards over the years

GadgetReboot/ATTiny_LFO
Dual low frequency oscillators using ATTiny and MCP4725 DACs

letelescope/ascom-flat-panel
Open source ASCOM and INDI driven automated flat panel for astrophotography
It measures 100 × 130 mm and has 2 copper layers, 1.6 mm thick.
53 parts, built around the MAX485ED, MCP4922-E/P, TLC272CD and MC7805CDTG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the LennardBoediger/dmx-fan-controller repository on GitHub, at the commit this page was made from: the board is hardware/fan-controller-pcb/fan-controller-pcb.kicad_pcb and its schematic hardware/fan-controller-pcb/fan-controller-pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).