
Uv bench
L-A-7/Electronic-design
Learning workspace for electronics and PCB design (KiCad 10, STM32): UV bench and following projects

Learning workspace for electronics and PCB design (KiCad 10, STM32): UV bench and following projects
Uv bench is an open-source printed circuit board by L-A-7, from the L-A-7/Electronic-design repository on GitHub. It is a 2-layer board of 70 × 55 mm with 90 parts on 51 nets, routed with 779 tracks and 80 vias.
It is built around the STM32C031F6P6, OPA2388IDGK and TLV9061IDBV, with the LM66100DCK, 74LVC1G08Z and 74LVC1G66GW among its other parts. Its parts include 26 resistors, 23 capacitors, 9 ICs, 6 connectors and 4 diodes. It belongs with the STM32 boards of this library.
This workspace is for building a reliable, repeatable toolchain for PCB design. Each project takes one step up in complexity, and each one has to be useful on its own.
| Folder | Content |
|---|---|
projects/ | One folder per board: docs/ hardware/ simulation/ firmware/ test/ |
library/ | Shared KiCad library (symbols, footprints, 3D models) for parts that aren't in the stock libs |
templates/ | KiCad project template (fab design rules, title block, net classes) |
tools/ | Scripts: ERC/DRC/fabrication exports through kicad-cli, simulation helpers |
learning/ | Notes and small exercises: protocols, UV safety, KiCad, circuit topics |
resources/ | Datasheets and application notes (stored locally, git-ignored if large) |
books/ | Reading notes |
lab/ | Instrument inventory, purchase plan, measurement procedures |
| Step | Tool | Status |
|---|---|---|
| Version control | git (one repo, one commit per meaningful design step) | initialised |
| Schematic / PCB | KiCad 9.0.8 | installed |
| Circuit simulation | ngspice inside the KiCad schematic editor (libngspice present); vendor SPICE models | available |
| Parameter sweeps | Python (spicelib or PySpice) driving ngspice | to do |
| Automated checks and exports | tools/kicad-check.sh (ERC, DRC, Gerbers, drill, BOM, position, PDF, STEP) | written |
| Mechanical fit | STEP export, then FreeCAD (installed) | available |
| Firmware | STM32CubeIDE / CubeMX on a Nucleo board until our own controller exists | to do |
| Protocol debugging | Logic analyser + sigrok/PulseView | to buy, see lab/ |
| Fabrication | JLCPCB / PCBWay (cheap PCBA) or Aisler (EU) | choose at milestone M4 |
| # | Project | Main new skills | Useful because |
|---|---|---|---|
| 1 | UV LED bench board (projects/01-uv-bench) | Power input protection, linear constant-current driver, photodiode TIA, small STM32 on board (control loop, I2C target, UART console), op-amp stability simulation, first full fab-and-test cycle | Self-regulating UV source: ask for a power, it holds it. Driven from a PC (USB-serial cable) now, from the main board over I2C later |
| 2 | (optional, later) Small STM32 USB controller (projects/02-usb-controller) | STM32 minimum system, USB-C FS device, SWD, crystal, USB CDC firmware | Drives the UV bench from a PC. Proves the USB + STM32 layout cheaply before the large board |
| 3 | Main STM32 board (projects/03-main-board) | USB-C PD power, stepper driver, 4 analogue acquisition channels, temperature, DACs, mixed-signal layout | The instrument controller |
Each project goes through the same milestones: M0 toolchain, M1 breadboard proof, M2 schematic and simulation, M3 layout and review, M4 fabrication, M5 bring-up and characterisation, M6 firmware and documentation.
NN-short-name.uv-bench-revA-fab.docs/ with its reasoning.tools/kicad-check.sh passes and the review checklist is done.| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C10, C11, C13, C14, C17, C19, C21 |
| 7 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R7, R9, R13, R23, R24, R25, R26 |
| 5 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C6, C7, C12 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R8, R10, R20 |
| 4 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R6, R12, R16 |
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R17, R21 |
| 3 | 10n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16, C22, C23 |
| 2 | 10u | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C5 |
| 2 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 2 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP4, TP13 |
| 2 | LM66100DCK | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U1, U2 |
| 1 | +3V3 | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | +5V | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | 0R33 1% 0.25W | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R14 |
| 1 | 1.1A hold | Fuse:Fuse_1812_4532Metric_Pad1.30x3.40mm_HandSolder | F1 |
| 1 | 10k 0.1% | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R22 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18 |
| 1 | 1n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C20 |
| 1 | 220R@100MHz 2A | Inductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolder | FB1 |
| 1 | 220u 10V | Capacitor_SMD:CP_Elec_6.3x7.7 | C4 |
| 1 | 22k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | 24k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | 2p2 C0G | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18 |
| 1 | 330k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19 |
| 1 | 4n7 | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C15 |
| 1 | 4u7 | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C9 |
| 1 | 5V_LED | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | 74LVC1G08 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U7 |
| 1 | 74LVC1G66 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U6 |
| 1 | ADDR 0x2B | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | ALT DETECTOR (K,A) | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | D4 |
| 1 | BPW 34 BS | OptoDevice:Osram_BPW34S-SMD | D3 |
| 1 | DRAIN | TestPoint:TestPoint_Pad_D1.5mm | TP11 |
| 1 | FTDI 3V3 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | GATE | TestPoint:TestPoint_Pad_D1.5mm | TP9 |
| 1 | ISENSE | TestPoint:TestPoint_Pad_D1.5mm | TP10 |
| 1 | Kelvin | NetTie:NetTie-2_SMD_Pad0.5mm | NT1 |
| 1 | LED star | Connector_Wire:SolderWire-0.25sqmm_1x02_P4.2mm_D0.65mm_OD1.7mm | J5 |
| 1 | MAIN JST-PH 4 | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J1 |
| 1 | NDT3055L | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | Q1 |
| 1 | NTC 10k | Connector_Wire:SolderWire-0.1sqmm_1x02_P3.6mm_D0.4mm_OD1mm | J6 |
| 1 | OPA2388IDGK | Package_SO:VSSOP-8_3x3mm_P0.65mm | U8 |
| 1 | PD_OUT | TestPoint:TestPoint_Pad_D1.5mm | TP12 |
| 1 | SCL | TestPoint:TestPoint_Pad_D1.5mm | TP6 |
| 1 | SDA | TestPoint:TestPoint_Pad_D1.5mm | TP5 |
| 1 | SET_F | TestPoint:TestPoint_Pad_D1.5mm | TP7 |
| 1 | SET_G | TestPoint:TestPoint_Pad_D1.5mm | TP8 |
| 1 | SMAJ5.0A | Diode_SMD:D_SMA_Handsoldering | D1 |
| 1 | STM32C031F6P6 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U5 |
| 1 | SWD | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J3 |
| 1 | TLV75533PDBV | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U3 |
| 1 | TLV9061IDBV | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U9 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | U4 |
| 1 | UV ARM switch | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J4 |
| 1 | green | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |

L-A-7/Electronic-design
Learning workspace for electronics and PCB design (KiCad 10, STM32): UV bench and following projects

L-A-7/Electronic-design
Learning workspace for electronics and PCB design (KiCad 10, STM32): UV bench and following projects

karimf1/rover-panel-pcb
This repository is continuation of rover panel repo. Power panel PCB layout is implemented in KiCAD based of AutoCAD version of rover panel .



nguyencanhanh/luckfox-rv1103-drone
AI quadcopter on one RV1103 (Luckfox Pico Mini B): Linux + RISC-V MCU flight loop, SITL with 3D pilot view, KiCad flight-controller board

fsanzeni/FSC-BT1104QI-Breakout
Breakout board for Feasycom FSC-BT1104QI (Bluetooth 5.4 / QCC3095) with USB-C/UART bridge, 3.3V LDO regulation, I2S digital audio, differential speaker outputs, and all pads broken out.


Richard42Graham/WLED-MOUSE
A WLED pcb for use with a microphone, and some othere bits, mainly for workshops and decoration.

GeneralCybernetics/Ion-Concentration-Biomodulator
PCB Designs and Documentation for a ion concentration biomodulator that induces HEK293T cells to reprogram and dedifferentiate into stem cells
It measures 70 × 55 mm and has 2 copper layers, 1.6 mm thick.
90 parts, built around the STM32C031F6P6, OPA2388IDGK, TLV9061IDBV and LM66100DCK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the L-A-7/Electronic-design repository on GitHub, at the commit this page was made from: the board is projects/01-uv-bench/hardware/archive/rev-a/uv-bench/uv-bench.kicad_pcb and its schematic projects/01-uv-bench/hardware/archive/rev-a/uv-bench/analog.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask L-A-7 before reusing the design.