Skip to the content
4 layers86 × 90 mmSc02 drive, the printed circuit board in 3D

SC-02 Solar Hypercar: 3D-printbare Le-Mans-racer op zonne-energie met Pi 4 + ESP32-S3, CadQuery-CAD en three.js-simulatie

Size
86 × 90 mm
Copper layers
4
Thickness
1.6 mm
Parts
94
Nets
102
Pads
394
Tracks, vias
652, 331
Pours
19
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
16 Oct 2026
Updated
22 Oct 2026

Overview

Sc02 drive is an open-source printed circuit board by KVR-CIBER, from the KVR-CIBER/sc02-solar-hypercar repository on GitHub. It is a 4-layer board of 86 × 90 mm with 94 parts on 102 nets, routed with 652 tracks and 331 vias.

It is built around the E28-2G4M12S, ESP32-C3-MINI-1-N4 and ESP32-S3-WROOM-1-N16R8, with the TPS54560BDDAR, AMS1117-3.3 and USBLC6-2SC6 among its other parts. Its parts include 29 resistors, 24 capacitors, 11 connectors, 9 diodes and 8 ICs. It belongs with the power boards and the ESP32 and RISC-V boards of this library.

Main components

12

README

f1/pcb/README.md

SC-02 drive board (v3.0)

A compact 86 x 90 mm board on 4x M3 standoffs, with the 3S LiPo on top of it. No Raspberry Pi anymore, a built-in ExpressLRS 2.4 GHz receiver for the RadioMaster Pocket, and a real solar-panel connector. (v2 was the whole car floor; that is gone: the car floor goes back to the 2 mm acrylic / printed floor.)

BlockParts
Power (unchanged from v2)XT60, 10 A fuse, power switch pads, P-MOSFET reverse protection, INA226 + 2 mOhm shunt, TPS54560B 5 V 5 A buck
Car brainESP32-S3-WROOM-1 (antenna at the bottom edge), USB-C at the edge, RESET / BOOT
Motorone brushless 2435 4500 KV + 40 A ESC (11:35). The ESC takes its power straight from the battery (Y-cable on the XT60); this board only sends the throttle signal (ESC header, IO4) and reads a 10k NTC on the ESC/motor (ESC TEMP, IO5) for the boost limit
ExpressLRS receiverESP32-C3-MINI-1 + Ebyte E28-2G4M12S (SX1280, 12.5 dBm, PCB antenna at the right edge), own 3.3 V LDO, RGB status LED, BIND button
Connectorsservo (MG90S), hall (A3144), lights (switched 5 V), solar panel JST-XH 2-pin, Qwiic I2C

Checks: DRC 0, unconnected 0, ERC 0, schematic parity 0. JLC BOM/CPL in fab/ with LCSC numbers.

ExpressLRS: flashing and binding

The receiver is wired exactly like ExpressLRS' "Generic C3 2400" target (SCK 6, MOSI 4, MISO 5, NSS 7, BUSY 3, DIO1 1, RST 2, LED 8, button 9, CRSF on 20/21), so the normal ExpressLRS firmware runs on it, no custom layout needed.

  1. First flash: ExpressLRS Configurator -> target Generic C3 2400 RX, flash method WiFi or via the RX USB pads (D-, D+, GND: a cut USB cable) while holding BIND at power-on.
  2. Bind with the Pocket (binding phrase, or press BIND 3x).
  3. CRSF goes to the car ESP32-S3: C3 TX -> IO16, S3 IO15 -> C3 RX (420000 baud). The S3 can reset the receiver (IO17 -> EN) and start its bootloader (IO18 -> IO9), so later updates can go through the car's USB-C. Tip: keep the S3's own WiFi off while driving (same 2.4 GHz band).

Solar panel

JST-XH 2-pin (- / +), voltage on IO8 (x 4.03). Solder jumper JP1 (ZON>5V), open by default: closed, the panel helps the 5 V rail through a Schottky diode. Only close it with a panel whose open-circuit voltage is at most 6 V.

ESP32-S3 pins

GPIOGPIO
4ESC throttle (servo PWM / DShot)5ESC/motor NTC (ADC)
9servo38hall
15 / 16CRSF TX / RX (receiver)17 / 18receiver EN / BOOT
1 / 2I2C SDA / SCL (INA226 0x40 + Qwiic)8solar panel voltage
11lights12yellow LED

Still to do

  • Car CAD: floor back to acrylic + 4 standoff holes for this board, battery tray on top, USB-C opening at the new place.
  • Firmware car.cpp: ESC on IO4 (with arming), CRSF on IO15/16, boost on CH5 with the NTC temperature limit, hall IO38.
  • ESC wiring: XT60 Y-cable battery -> ESC + this board; do NOT connect the ESC's red BEC wire to the board.

Parts

94
QtyValueFootprintReferences
810ksc02:R_0603_1608MetricR1, R11, R12, R19, R21, R31, R32, R33
7100nsc02:C_0603_1608MetricC2, C7, C8, C16, C18, C32, C34
4100sc02:R_0603_1608MetricR18, R20, R29, R30
4M3sc02:Hole_3.2mmH1, H2, H3, H4
310usc02:C_0805_2012MetricC14, C30, C33
31ksc02:R_0603_1608MetricR13, R34, R35
31usc02:C_0603_1608MetricC19, C29, C35
322usc02:C_0805_2012MetricC15, C17, C31
347u 10Vsc02:C_1210_3225MetricC9, C10, C11
3SS14sc02:D_SMAD6, D7, D9
2100ksc02:R_0603_1608MetricR22, R26
210u 25Vsc02:C_1206_3216MetricC5, C6
24k7sc02:R_0603_1608MetricR24, R25
25k1sc02:R_0603_1608MetricR27, R28
2AMS1117-3.3sc02:SOT-223-3_TabPin2U2, U13
110.2ksc02:R_0603_1608MetricR8
1100u 25Vsc02:CP_Elec_6.3x7.7C1
110Asc02:R_2512_6332MetricF1
116.9ksc02:R_0603_1608MetricR9
1243ksc02:R_0603_1608MetricR6
12k2sc02:R_0603_1608MetricR10
12msc02:R_2512_6332MetricRS1
133ksc02:R_0603_1608MetricR23
1442ksc02:R_0603_1608MetricR4
147psc02:C_0603_1608MetricC13
14n7sc02:C_0603_1608MetricC12
153.6ksc02:R_0603_1608MetricR7
16.8usc02:L_Bourns_SRP1038C_10.0x10.0mmL1
190.9ksc02:R_0603_1608MetricR5
1AO3400Asc02:SOT-23Q4
1AOD4185sc02:TO-252-2Q1
1B560Csc02:D_SMCD4
1BINDsc02:SW_Push_1P1T_NO_CK_KMR2SW3
1BOOTsc02:SW_Push_1P1T_NO_CK_KMR2SW2
1BZT52C15sc02:D_SOD-123D2
1E28-2G4M12Ssc02:WIRELM-SMD_E28-2G4M12SU12
1ESCsc02:PinHeader_1x03_P2.54mm_VerticalJ2
1ESC TEMPsc02:SolderWire_2pad_P5mm_MJ3
1ESP32-C3-MINI-1-N4sc02:WIFIM-SMD_ESP32-C3-MINI-1U11
1ESP32-S3-WROOM-1-N16R8sc02:ESP32-S3-WROOM-1U3
1HALLsc02:PinHeader_1x03_P2.54mm_VerticalJ5
1I2Csc02:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_HorizontalJ7
1INA226sc02:TSSOP-10_3x3mm_P0.5mmU6
1LICHTENsc02:SolderWire_2pad_P4mm_SJ10
1RESETsc02:SW_Push_1P1T_NO_CK_KMR2SW1
1RX USBsc02:Pads_RX_USBJ12
1SCHAKELAARsc02:SolderWire_2pad_P5mm_SWJ11
1SERVOsc02:PinHeader_1x03_P2.54mm_VerticalJ4
1SK6812MINI-Esc02:LED-SMD_4P-L3.2-W2.8-LS5.9_SK6812MINI-ED10
1SMBJ15CAsc02:D_SMBD1
1TPS54560Bsc02:Texas_R-PDSO-G8_EP2.95x4.9mm_Mask2.4x3.1mm_ThermalViasU1
1USB-Csc02:USB_C_Receptacle_HRO_TYPE-C-31-M-12J8
1USBLC6-2SC6sc02:SOT-23-6U10
1XT60sc02:AMASS_XT60-M_1x02_P7.20mm_VerticalJ1
1ZON>5Vsc02:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJP1
1ZONNEPANEELsc02:JST_XH_B2B-XH-A_1x02_P2.50mm_VerticalJ6
1geel ESPsc02:LED_0603_1608MetricD8
1groen 5Vsc02:LED_0603_1608MetricD5

Similar boards

  • 2 layers141.8 × 50 mmCwl, the printed circuit board in 3D

    Cwl

    philipparndt/opentherm-wolf-cwl

    Decoder tool for analyzing OpenTherm protocol communication between a BM remote control and a Wolf CWL ventilation/heat-recovery unit. Built to reverse-engineer the protocol for building a custom ESP32-based controller.

    63 parts
  • 4 layers76 × 54 mmPixelblaze battery backpack, the printed circuit board in 3D

    Pixelblaze battery backpack

    SK-Electronics-Consulting/electronics-widgets

    Small, Custom Tools for Electronics

    112 parts1
  • 4 layers150 × 155 mmUsb console server, the printed circuit board in 3D

    Usb console server

    TheKingOfChaos/Console-Server

    48 RS-232 console ports on one Raspberry Pi: three identical boards, 16 ports each. Built from the design record of 2026-10-10. KiCad 10.0.7. This is Rev B (git tag rev-A is the first board).

    361 parts
  • 4 layers81 × 90.3 mmMildly Overkill, the printed circuit board in 3D

    Mildly Overkill

    hackepeter101/Mildly-Overkill

    todo.md was written entirely by AI. It's the list of everything it found. I read the suggestions, double-check them, and then fix them myself in KiCad, usually while muttering.

    138 parts1
  • 2 layers100 × 100 mmAquaPCB, the printed circuit board in 3D

    AquaPCB

    schwabix-1311/aquaPCB

    Open-hardware Raspberry Pi base board for aquaPi software. 12 V supply; six 5 A MOSFET outputs for LED lamps and fans (2 with hardware PWM); 4 SSR/relay drivers; protected inputs; 1-Wire; ADS1115 with a pH amplifier on…

    147 partsCERN-OHL-S-2.0
  • 2 layers35.4 × 33.5 mmSx1280 breakout, the printed circuit board in 3D

    Sx1280 breakout

    JeremyGrosser/breakouts

    Random breakout boards, rarely useful

    10 parts1
  • 4 layers19 × 24.1 mmLutje v1, the printed circuit board in 3D

    Lutje v1

    WRusman/Lutje

    Open-source Battlebot ELRS receiver with built-in ESC's' for 2 brushed driving motors, 1 brushed weapon motor and 2 PWM outputs for external ESC.

    46 parts1
  • 2 layers27.7 × 53.8 mmUnfancyRemote, the printed circuit board in 3D

    UnfancyRemote

    kitspace-test-repos/kicad6-file-collection

    43 partsMIT

Questions

How big is the Sc02 drive PCB?

It measures 86 × 90 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Sc02 drive use?

94 parts, built around the E28-2G4M12S, ESP32-C3-MINI-1-N4, ESP32-S3-WROOM-1-N16R8 and TPS54560BDDAR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Sc02 drive KiCad files?

From the KVR-CIBER/sc02-solar-hypercar repository on GitHub, at the commit this page was made from: the board is f1/pcb/sc02_drive.kicad_pcb and its schematic f1/pcb/sc02_drive.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Sc02 drive design in my own project?

Its repository states no licence, so its author keeps all rights: ask KVR-CIBER before reusing the design.