Skip to the content
2 layers39.9 × 46.4 mmCrealityDryer, the printed circuit board in 3D

Creality Space Pi Plus CFS mod automation (PCB and sketch for Arduino IDE)

Size
39.9 × 46.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
54
Pads
138
Tracks, vias
475, 47
Pours
1
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
17 Jun 2025
Updated
9 Aug 2025

Overview

CrealityDryer is an open-source printed circuit board by Ermakov, from the Ermakov/CrealitySpacePiAutomation repository on GitHub. It is a 2-layer board of 39.9 × 46.4 mm with 18 parts on 54 nets, routed with 475 tracks and 47 vias.

It is built around the ATMEGA328P-AU. Its parts include 6 capacitors, 5 connectors, 2 resistors, 1 IC and 1 crystal. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

Creality SpacePi automation and control module

This is PCB and Arduino IDE sketch for Creality Space Pi (Plus or not) automation.

Description:

  • necessary the module itself and IDC10 female-male cable
  • can be inserted into any Creality SpacePi dryer (double, single, built-in Creality CFS or not)
  • other functions and cables are optional (backlights, external control and power are not required for operation, but can be connected additionally)
  • the cable from the SpacePi display needs to be disconnected from the dryer board and inserted into the "display" socket on the module
  • an additional IDC10 cable connecting between the module "mainboard" socket and the dryer board (power is supplied from the dryer board via this cable)
  • RJ45 on the module connecting to any I2C master using a regular patch cord and provides data transfer in both directions, and also serves lighting (24V led strip) inside CFS or dryer
  • two pin terminal block on the module used for connecting the led strip; pad J4 on the back of the module (via diode) used for supply 24 volts to the strip directly from CFS (without connecting a patch cord with external power)

Module/sketch features:

  • interception of all signals between the display/buttons and the dryer board, the module sees the readings on the display and can control the dryer buttons
  • automatic switching on SpacePi after power is supplied
  • automatic switching on SpacePi drying mode to the values on the display when the module sees humidity above the set point (by default 30%, switching on for 4 hours, then a break of 4 hours, and so on)
  • solving the problem with the E4 error (when the dryer does not reach the expected temperature within 10 minutes) by restarting the drying mode every 9 minutes (until heating to the working temperature)
  • transferring data of temperature/humidity in the dryer via I2C as HTU21D sensor protocol
  • any information from the dryer display (including an error), as well as pressing any buttons using special I2C commands (see the sketch)

Parts

18
QtyValueFootprintReferences
3100nFCapacitor_SMD:C_0603_1608MetricC1, C3, C4
210KResistor_SMD:R_0603_1608MetricR2, R3
210pFCapacitor_SMD:C_0603_1608MetricC5, C6
1100RResistor_SMD:R_Array_Convex_4x0603RN2
116MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
11KResistor_SMD:R_Array_Convex_4x0603RN1
122uF 10VCapacitor_Tantalum_SMD:CP_EIA-3528-12_Kemet-TC2
18P8CMegaSensor:RJ45_OST_PJ012-8P8CX_VerticalSensorJ1
1ATmega328P-APackage_QFP:TQFP-32_7x7mm_P0.8mmU2
1Arduino_Nano_v2.xMegaSensor:Arduino_NanoA1
1DisplayMegaSensor:IDC-Header_2x05_P2.54mm_VerticalSilkJ3
1MainBoardMegaSensor:IDC-Header_2x05_P2.54mm_VerticalSilkJ2
1PROGConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ5
1UART PROGConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ4

More from Ermakov/CrealitySpacePiAutomation

1
  • 2 layers39.9 × 46.4 mmCrealityDryerV1, the printed circuit board in 3D

    CrealityDryerV1

    Ermakov/CrealitySpacePiAutomation

    Creality Space Pi Plus CFS mod automation (PCB and sketch for Arduino IDE)

    20 parts33

Similar boards

  • 2 layers50.5 × 128.5 mmOpenThereminV45, the printed circuit board in 3D

    OpenThereminV45

    GaudiLabs/OpenThereminV4

    Open Source Theremin Instrument

    107 parts249GPL-3.0
  • 2 layers152 × 88 mmRFBitBangSMT, the printed circuit board in 3D

    RFBitBangSMT

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    271 parts222
  • 2 layers50.2 × 31.2 mmMCU Datalogger, the printed circuit board in 3D

    MCU Datalogger

    futureshocked/KLP4e_MCU-Datalogger

    This is the repository for the "MCU Datalogger" project.

    31 parts138MIT
  • 2 layers34 × 46 mmNfcemu, the printed circuit board in 3D

    Nfcemu

    solosky/nfc-emu

    NFC模拟器

    58 parts117Apache-2.0
  • 2 layers73 × 94 mmSportiduino base, the printed circuit board in 3D

    Sportiduino base

    sportiduino/sportiduino

    Electronic timing system for orienteering and similar outdoor sports events on Arduino

    119 parts78GPL-3.0
  • 2 layers58.9 × 44.2 mmOpenPSX2AmigaPadAdapter, the printed circuit board in 3D

    OpenPSX2AmigaPadAdapter

    SukkoPera/OpenPSX2AmigaPadAdapter

    Playstation to Commodore Amiga/CD32 Controller Adapter

    43 parts69
  • 2 layers60 × 50 mmVx8 gps prototype v2.0, the printed circuit board in 3D

    Vx8 gps prototype v2.0

    4x1md/vx8_gps

    DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.

    56 parts66MIT

Questions

How big is the CrealityDryer PCB?

It measures 39.9 × 46.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CrealityDryer use?

18 parts, built around the ATMEGA328P-AU. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CrealityDryer KiCad files?

From the Ermakov/CrealitySpacePiAutomation repository on GitHub, at the commit this page was made from: the board is CrealityDryerArduinoPCB(KiCad8)/CrealityDryer.kicad_pcb and its schematic CrealityDryerArduinoPCB(KiCad8)/CrealityDryer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CrealityDryer design in my own project?

Its repository states no licence, so its author keeps all rights: ask Ermakov before reusing the design.